2004 SUZUKI GRAND VITARA wheel

YH4
GRAND
VITARA
1. Oil filler / level plug
2. Front drain plug
1. Circlip
2. Washer
1. Differential side joint
2. Tire lever
3. Front differential assembly
1. Oil seal 2
1
4A2-4 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
REMOVAL (RIGHT SIDE)
1) Hoist vehicle and remove wheel.
2) Drain differential gear oil.
3) Remove axle shaft drive flange.
4) Remove circlip and front spindle thrust washer.
5) Remove knuckle and wheel hub comp, refer to steps 5) to 7) and
9) to 14) of item COIL SPRING REMOVAL in Section 3D.
6) Remove drive shaft assembly.
To detach snap ring fitted on the spline of differential side joint
(inboard joint) from differential side gear, pull inboard joint by us-
ing a tire lever.
CAUTION:
To prevent breakage of boots (wheel side and differential
side), be careful not to bring them into contact with other
parts when removing drive shaft assembly.
7) Remove drive shaft thrust washer (to vehicle with G16 or J20 en-
gine) from drive shaft and remove drive shaft oil seal as shown
in figure.
CAUTION:
Be careful not to cause damage to drive shaft joint.

YH4
GRAND
VITARA
1. Boot
2. Snap ring
1. Circlip
2 Snap ring plier
3. Cage
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-5
DISASSEMBLY
1) Remove boot band of differential side joint.
2) Slide boot toward the center of shaft and remove snap ring from
outer race, then take shaft out of outer race.
3) Remove circlip and then cage.
4) Remove inside and outside boots from shaft.
CAUTION:

Do not disassemble wheel side joint (outboard joint). If
any malcondition is found in joint, replace it as assem-
bly.

Do not disassemble ball joint of differential side joint.
If any malcondition is found in ball joint, replace differ-
ential side joint assembly.
INSPECTION

Check boots for breakage or deterioration. Replace them as nec-
essary.

Check circlip, snap ring and boot bands for breakage or deforma-
tion. Replace as necessary.
CLEANING

Wash disassembled parts (except boots) in degreaser. After
washing, dry parts completely by blowing air.

Clean boots with cloth. DO NOT wash boots in degreaser, such
as gasoline or kerosene, etc.
Washing in degreaser causes deterioration of boot.

YH4
GRAND
VITARA
1. Boot
2. Boot band
1. Circlip1. Cage Wheel side
ªAº Fill grease 85g (3.0 oz)
4A2-6 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
ASSEMBLY
CAUTION:

To prevent any problem caused by washing solution, do
not wash joint boots. Degreasing of those parts with cloth
is allowed.

For M / T vehicle with H25 engine
To ensure full performance of joint as designed, be sure
to distinguish between two types of grease in repair set
and apply specified volume to respective joint. i.e. yellow
grease to wheel side joint and black one to differential
side.

Bend each boot band against forward rotation.

Do not squeeze or distort boot when fastening it with
bands.
Distorted boot caused by squeezing air may reduce its du-
rability.
1) Fully apply joint grease to wheel side joint.
Use joint grease in the tube included in spare part.
2) Fit wheel side boot on shaft.
Fill up inside of boot with joint grease of about 90 gram.
Before fixing boot band, insert screwdriver into boot on joint side
and allow air to enter boot so that air pressure in boot becomes
the same as atmospheric pressure.
3) Fixing boot band.
4) Install boot onto drive shaft till its small diameter side fits to shaft
groove and fix there with boot band.
5) Install cage to shaft.
CAUTION:
Install cage directing smaller outside diameter side to
shaft end.
6) Install circlip by using snap ring plier.

YH4
GRAND
VITARA
1. Drive shaft oil seal
1. Drive shaft flange bolt and nut
2. Front spindle thrust washer
3. Axle shaft drive flange
ªAº
1. Drive shaft joint
2. Oil seal
3. Pipe
4. Thrust washer4
4A2-8 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
INSTALLATION
Install drive shaft assembly by reversing removal procedure and
noting following points.

Clean front drive shaft oil seal and then apply lithium grease to oil
seal and DOJ shaft.
ªAº: Grease 99000-25010

Check oil seal for breakage or deterioration.
Replace it as necessary.

Drive in oil seal until its end contacts stepped surface of drive
shaft joint by using a pipe whose inner diameter is 76 mm (2.992
in.) or more and outer diameter is 80 mm (3.150 in.) or less.
Diameter ªaº: 76 mm (2.992 in.) or more
Diameter ªbº: 80 mm (3.150 in.) or less

Drive in drive shaft thrust washer (Vehicle with G16 or J20 en-
gine).

RH Side
Push differential side joint by hand until it is positioned by snap
ring fitted to its spline.
LH Side
Connect drive shaft flange bolts and nuts.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

Apply grease to front spindle thrust washer and front spindle part
of drive shaft.
ªAº: Grease 99000-25010

When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange.
ªBº: Sealant 99000-31090
Tightening Torque
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
CAUTION:

To prevent breakage of boots (wheel side and differen-
tial side), be careful not to bring them into contact with
other parts when installing drive shaft assembly.

Do not pull housing of differential side joint.
If housing is pulled, it may be detached from drive shaft.

Fill specified differential gear oil into differential case to specified
level.

YH4
GRAND
VITARA
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-11
09913-75520
Bearing installer09924-74510
Installer attachment09930-30102
Sliding shaft09941-64510
Bearing remover
09951-16090
Oil seal installer
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Drive shaft flange nut (Dif. side)505.036.5
Oil level plug232.317.0
Drain plug232.317.0
Axle shaft drive flange bolt484.835.0
NOTE:
Refer to standard tightening torque specifications, if no description or specification is provided.
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Joint grease
(Molybdenum grease)SUZUKI SUPER GREASE H
(99000-25120)Drive axle joint
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)Drive shaft oil seal
Wheel spindle part of differential side
drive shaft (RH)
SealantSEALING COMPOUND 366E
(99000-31090)Axle shaft drive flange
SPECIAL TOOLS

YH4
GRAND
VITARA
[FOR VEHICLE WITHOUT ABS]
[FOR VEHICLE WITH ABS]
1. Master cylinder
2-1. 4-way joint
2-2. 2-way joint
3. LSPV (Load Sensing Proportioning Valve)
4. Rear axle housing
5. ABS actuator (H.U.)
F.R.:Front side
5-2 BRAKES
GENERAL DESCRIPTION
When the foot brake pedal is depressed, hydraulic pressure is developed in the master cylinder to actuate pistons
(two in front and four in rear).
The master cylinder is a tandem master cylinder. Brake pipes are connected to the master cylinder and they make
two independent circuits. One connects front brakes (right and left) and the other connects rear brakes (right and
left).
The load sensing proportioning valve (LSPV) is included in these circuits between the master cylinder and the rear
brake for the vehicle without ABS.
In this brake system, the disc brake type is used for the front wheel brake and a drum brake type (leading / trailing
shoes) for the rear brake.
The parking brake system is mechanical. It applies brake force to only rear wheels by means of the cable and me-
chanical linkage system. The same brake shoes are used for both parking and foot brakes.

YH4
GRAND
VITARA
BRAKES 5-3
SUBSTANDARD OR
CONTAMINATED BRAKE FLUID
Improper brake fluid, mineral oil or water in the fluid
may cause the brake fluid to boil or the rubber compo-
nents in the hydraulic system to deteriorate.
If primary piston cups are swollen, then rubber parts
have deteriorated. This deterioration may also be evi-
denced by swollen wheel cylinder piston cups on the
drum brake wheels.
If deterioration of rubber is evident, disassemble all
hydraulic parts and wash with alcohol. Dry these parts
with compressed air before assembly to keep alcohol
out of the system. Replace all rubber parts in the sys-
tem, including hoses. Also, when working on the
brake mechanisms, check for fluid on the linings. If ex-
cessive fluid is found, replace the linings.
If master cylinder piston seals are satisfactory, check
for leakage or excessive heat conditions. If condition
is not found, drain fluid, flush with brake fluid, refill and
bleed system.
The system must be flushed if there is any doubt as
to the grade of fluid in the system or if fluid has been
used which contained parts that have been subjected
to contaminated fluid.
DIAGNOSIS
ROAD TESTING BRAKES
Brakes should be tested on dry, clean, smooth and
reasonably level roadway which is not crowned. Road
test brakes by making brake applications with both
light and heavy pedal forces at various speeds to de-
termine if the vehicle stops evenly and effectively.
Also drive vehicle to see if it leads to one side or the
other without brake application. If it does, check the
tire pressure, front end alignment and front suspen-
sion attachments for looseness. See diagnosis chart
for other causes.
BRAKE FLUID LEAKS
Check the master cylinder fluid levels. While a slight
drop in reservoir level does result from normal lining
wear, an abnormally low level indicates a leak in the
system. In such a case, check the entire brake system
for leakage. If even a slight evidence of leakage is
noted, the cause should be corrected or defective
parts should be replaced.
If fluid level is lower than the minimum level of reser-
voir, refilling is necessary. Fill reservoir with specified
brake fluid.
Brake fluid: Refer to reservoir tank cap.
CAUTION:
Since brake system of this vehicle is factory-
filled with brake fluid indicated on reservoir
tank cap, do not use or mix different type of
fluid when refilling; otherwise serious damage
will occur.
Do not use old or used brake fluid, or any fluid
from a unsealed container.

YH4
GRAND
VITARA
5-4 BRAKES
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Not enough brak-
ing force
Brake oil leakage from brake lines.

Brake disc or pads stained with oil.

Overheated brakes.

Poor contact of shoes on brake drum.

Brake shoes linings stained with oil or wet
with water.

Badly worn brake shoe linings.

Defective wheel cylinders.

Malfunctioning caliper assembly.

Air in system.

Maladjusted sensor spring length of LSPV.

Broken sensor spring of LSPV.

Defective collar of LSPV.

Malfunctioning ABS (Antilock brake system),
if equipped.Locate leaking point and repair.
Clean or replace.
Determine cause and repair.
Repair for proper contact.
Replace.
Replace.
Repair or replace.
Repair or replace.
Bleed system.
Check or adjust.
Replace.
Replace.
Check system and replace as
necessary.
Brake pull
(Brakes not work-
ing in unison)
Pad or shoe linings are wet with water or
stained with oil in some brakes.

Drum-to-shoe clearance out of adjustment in
some brakes.
(Malfunctioning auto adjusting mechanism)

Drum is out of round in some brakes.

Wheel tires are inflated unequally.

Malfunctioning wheel cylinders.

Disturbed front end alignment.

Unmatched tires on same axle.

Restricted brake pipes or hoses.

Malfunctioning caliper assembly.

Loose suspension parts.

Loose calipers.Replace.
Check for inoperative auto adjusting
mechanism.
Replace.
Inflate equally.
Repair or replace.
Adjust as prescribed.
Tires with approximately the same
amount of tread should be used on the
same axle.
Check for soft hoses and damaged
lines.
Replace with new hoses and new
brake pipes.
Check for stuck or sluggish pistons
and proper lubrication of caliper slide
bush.
Caliper should slide.
Check all suspension mountings.
Check and torque bolts to specifica-
tions.
Noise (High pitched
squeak without
brake applied)
Front lining worn out.Replace linings.
Rear brake locked
prematurely
Maladjusted sensor spring length of LSPV.

Malfunction LSPV assembly.Check or adjust.
Replace assembly.
Brake locked
(For vehicles
equipped with
ABS)
Malfunctioning ABS, if equipped.Check system and replace as
necessary.