2004 SUZUKI GRAND VITARA Transmission

YH4
GRAND
VITARA
7B1-78 AUTOMATIC TRANSMISSION (4 A / T)
ON-VEHICLE
SERVICE MOUNTING
EXTERNAL
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
Fastening portion
Tightening torque
Fastening portion
N´mkg-mlb-ft
Automatic transmission fluid drain plug232.317.0
Transfer oil filler / level and drain plugs232.317.0
Transmission case plug171.712.5
Manual select lever nut131.39.5
Manual select cable nut70.75.5
Manual selector assembly bolts181.813.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts
Engine rear mounting member bolts
Transmission case right stiffener bolts
505.036.5
Universal joint flange bolts and nuts505.036.5
Torque converter mounting bolts656.547.0
Adapter case or extension case bolts
(G16 engine)353.525.5
Adapter case or extension case bolts
(J20 / H25 engines)424.230.0
Transmission range switch lock bolt5.50.554.0
Oil pipe union bolts353.522.5
Drive plate bolts787.856.5
Interlock cable clamp screw2.20.221.5
Interlock cable outer mounting nut131.39.5

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-79
09925-37810
Oil pressure gauge09927-56010
Gear stopper
(only for G16 / J20)09931-76030
16 / 14 pin DLC
(OBD-II adapter) cable
09931-76011
SUZUKI scan tool (Tech 1A) kit1. Storage case
2. Operator's manual
3. Tech 1A
4. DLC cable
5. Test lead / probe
6. Power source cable
7. DLC cable adapter
8. Self±test adapterMass storage cartridge
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
A / T fluidAn equivalent of DEXRON-III
Automatic transmission

Parts lubrication when installing
Lithium greaseSUZUKI SUPER GREASE A
(99000±25010)
Cable ends
SealantSUZUKI BOND NO.1215
(99000-31110)
Flywheel bolts
SPECIAL TOOLS

YH4
GRAND
VITARA
1. Crankshaft
2. Flywheel
3. Clutch disc
4. Pressure plate
5. Clutch cover
6. Diaphragm spring
7. Release bearing
8. Input shaft bearing
9. Input shaft
10. Operating cylinder
11. Clutch housing
12. Release fork
7C1-2 CLUTCH
The clutch is a diaphragm-spring clutch of a dry single
disc type. The diaphragm spring is of a tapering-finger
type, which is a solid ring in the outer diameter part,
with a series of tapered fingers pointing inward.
The disc, carrying torsional coil springs, is positioned
on the transmission input shaft with an involute spline
fit.
The clutch cover is secured to the flywheel, and car-
ries the diaphragm spring in such a way that the pe-
ripheral edge part of the spring pushes on the pres-
sure plate against the flywheel (with the disc in be-
tween), when the clutch release bearing is held back.
This is the engaged condition of the clutch.Depressing the clutch pedal causes the release bear-
ing to advance and pushes on the tips of the tapered
fingers of the diaphragm spring. When this happens,
the diaphragm spring pulls the pressure plate away
from the flywheel, thereby interrupting the flow of
drive from flywheel through clutch disc to transmis-
sion input shaft.
GENERAL DESCRIPTION

YH4
GRAND
VITARA
CLUTCH 7C1-3
DIAGNOSIS
ConditionPossible CauseCorrection
Slipping
Improper clutch pedal free travel.

Worn or oily clutch disc facing.

Warped disc, pressure plate or flywheel
surface.

Weakened diaphragm spring.

Master cylinder piston or seal cup not returning.Bleed air or replace master
cylinder.
Replace disc.
Replace disc, clutch cover or
flywheel.
Replace clutch cover.
Repair master cylinder.
Dragging clutch
Improper clutch pedal free travel.

Weakened diaphragm spring, or worn spring tip.

Rusted input shaft splines.

Damaged or worn splines of transmission
input shaft.

Excessively wobbly clutch disc.

Clutch facings broken or dirty with oil.

Fluid leakage.Bleed air or replace master
cylinder.
Replace clutch cover.
Lubricate.
Replace input shaft.
Replace disc.
Replace disc.
Repair or replace.
Clutch vibration
Glazed (glass-like) clutch facings.

Clutch facings dirty with oil.

Release bearing slides unsmoothly on input
shaft bearing retainer.

Wobbly clutch disc, or poor facing contact.

Weakened torsion springs in clutch disc.

Clutch disc rivets loose.

Distorted pressure plate or flywheel surface.

Weakened or loosened engine mounting
bolt or nut.Repair or replace disc.
Replace disc.
Lubricate or replace input
shaft bearing retainer.
Replace disc.
Replace disc.
Replace disc.
Replace clutch cover or flywheel.
Retighten or replace mounting.
Noisy clutch
Worn or broken release bearing.

Input shaft front bearing worn down.

Excessive rattle of clutch disc hub.

Cracked clutch disc.

Pressure plate and diaphragm spring rattling.Replace release bearing.
Replace input shaft bearing.
Replace disc.
Replace disc.
Replace clutch cover.
Grabbing clutch
Clutch disc facings soaked with oil.

Clutch disc facings excessively worn.

Rivet heads showing out of facing.

Weakened torsion springs.Replace disc.
Replace disc.
Replace disc.
Replace disc.

YH4
GRAND
VITARA
CLUTCH 7C1-13
1. Release fork
2. Clip
3. Input shaftªBº
ªBº
ªAº 3
2
1
1
2
4) Install clip to release fork and apply grease.
ªAº: Grease 99000-25010
Then install release fork and release bearing as shown in figure.
5) Slightly apply grease to input shaft and install clutch disc. Then
join transmission transfer assembly with engine. Refer to SEC-
TION 7A.
ªBº: Grease 99000-25210
NOTE:
Turn crankshaft with wrench from front while inserting
transmission input shaft to clutch disc until splines mesh.

YH4
GRAND
VITARA
7D
TRANSFER 7D-1
The aluminum transfer case directly connected to the
back of the transmission contains the input gear,
countershaft & gear, output rear shaft, output low gear
and output front shaft (for front drive) connected by
way of the hyvo-chain.
The transfer has such a selective mechanism as to
enable the shift control lever to make selection of high
speed (direct connection with transmission output:
main shaft), low speed (speed reduction by input
gear, counter gear and output low gear) or neutral by
way of the reduction sleeve located between input
gear and output low gear, and selection of two-wheel-
drive (high speed only) or four-wheel-drive (high or
low speed) by way of the front drive clutch sleeve lo-cated at the center of the output rear shaft. Also, with
a synchronizer installed to the front drive clutch, it is
possible to change the drive mode between 2WD
(high speed only) and 4WD (high speed only) even
while running.
The front drive shift fork has an auxiliary spring to
make a smooth shift from 4H to 2H possible.
The case has an oil gutter and a plate at synchronizer
to provide proper lubrication even under the strict
conditions of use.
WARNING:
For towing the vehicle for the purpose of repair or
the like, follow the towing instructions in OWN-
ER'S MANUAL.
SECTION 7D
TRANSFER
CONTENTS
GENERAL DESCRIPTION7D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Oil Seals7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer Driven Gear7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Assembly7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismounting7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remounting7D-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION

YH4
GRAND
VITARA
1. Wood block
2. Dash panel
t: 45 mm / 1.8 in.
H: 200 mm / 8 in.
W: 100 ± 150 mm / 4 ± 6 in.
1. Transmission jack
2. Engine rear mounting member
3. Gear shift lever case
4. Bolt
TRANSFER 7D-5
TRANSFER ASSEMBLY
Dismounting and remounting of transfer and transmission together
as a unit is described in Section 7A for Manual Transmission or 7B1
for Automatic Transmission, but it is also possible to dismount and
remount transfer assembly by itself as described below.
DISMOUNTING
IN ENGINE ROOM
1) Disconnect negative (±) cable from battery.
2) Remove distributor assembly (if equipped).
3) Place wood block between engine and dash panel so that it
serves as stopper when engine, transmission and transfer unit
hangs down as rear mounting member is removed.
CAUTION:
Make sure to use wood block to prevent contact which
may occur between dash panel and CMP sensor case
(G16), CMP sensor (J20) or intake manifold (H25), and fan
and shroud.
IN CABIN
1) Remove console box.
2) Remove shift lever of transmission and transfer.
ON LIFT
1) Drain transfer oil.
2) Remove rear propeller shaft.
3) Remove front propeller shaft.
4) Disconnect exhaust center pipe.
5) Disconnect speed sensor coupler.
6) Place transmission jack and remove mounting member.
7) Lower transmission jack gradually and check to ensure that
wood block serves as stopper between engine and dash panel.
8) Remove bolts for gear shift lever case.
9) Pull off breather hose.

YH4
GRAND
VITARA
1. Bolt
2. Transfer assembly
1. Bolt
2. Engine rear mounting3. Transfer assembly
1. Bolt
2. Transfer assembly
3. Transmission jack
7D-6 TRANSFER
IN CABIN
Remove gear shift lever case and then remove transfer center case
bolt.
ON LIFT
1) Remove transfer mounting (engine rear mounting) by removing
bolts.
2) Apply transmission jack to transfer to support it.
3) Remove couplers for 4WD / 4WD-LOW switches lead.
4) Remove transfer front case bolts.
5) With transfer assembly supported with transmission jack, slide
it rearward and when it is apart from transmission, lower it.
REMOUNTING
For remounting, reverse dismounting procedure described above,
noting following.

Be sure to use specified torque for tightening.

Clamp wiring and breather hose securely.

Clamp shift lever boot securely.

Fill specified gear oil by specified amount.

Connect battery and check for function.