2004 SUZUKI GRAND VITARA rod

YH4
GRAND
VITARA
5A-16 BRAKES PIPE / HOSE / MASTER CYLINDER
1. Clevis
2. Nut
1. Steering column 4. Clevis pin
2. Push rod clevis 5. Clip
3. Brake pedal arm 6. NutBOOSTER PUSH ROD CLEVIS ADJUSTMENT
Install push rod clevis so that measurement ªaº is obtained and
torque nut to specification.
Tightening Torque
(a): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
Length
ªaº: 109.5 ± 110.5 mm (4.31 ± 4.35 in.)
INSTALLATION
NOTE:

See NOTE at the beginning of this section.

Check length of push rod clevis. (Refer to BOOSTER PUSH
ROD CLEVIS ADJUSTMENT.)

Before installing master cylinder, adjust booster piston rod.
(Refer to CLEARANCE BETWEEN BOOSTER PISTON ROD
AND MASTER CYLINDER PISTON ADJUSTMENT of this sec-
tion.)

Apply silicone grease to master cylinder piston.
1) Install booster to dash panel as shown. Then connect booster
push rod clevis to pedal arm with clevis pin and clip.
2) Tighten booster attaching nuts to the specified torque.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
3) Connect brake vacuum hose to brake booster.
4) For vehicle equipped with ABS, connect brake pipes to ABS hy-
draulic unit. If ABS hydraulic unit bracket bolts removed, tighten
flare nuts to specification after installing master cylinder.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 12.0 lb-ft)
5) Install master cylinder, referring to MASTER CYLINDER AS-
SEMBLY INSTALLATION in this section.

YH4
GRAND
VITARA
BRAKES PIPE / HOSE / MASTER CYLINDER 5A-19
09922-85811
Connector pin remover09950-96010
Booster piston rod gauge09952-16010
Booster piston rod adjuster
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake flexible hose bolt (Brake caliper / 2 (4) way joint)232.317.0
Master cylinder attaching nut131.39.5
Booster nut131.39.5
Clevis nut252.518
2-way (or 4-way) joint mounting bolt101.07.5
Brake pipe flare nut161.611.5
Front caliperM88.00.86.0
Brake bleederplug
Front cali erM108.50.856.5Brake bleeder lugWheel cylinder7.50.755.5
LSPV8.00.86.0
LSPV mounting bolt
LSPV stay bolt232.317.0
LSPV spring nut
Wheel nut10010.072.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.
SPECIAL TOOLS

YH4
GRAND
VITARA
[A]: TOKICO produced
[B]: SUMITOMO ELECTRIC produced1. Caliper pin bolt
2. Boot
3. Disc brake caliper
(Disc brake cylinder)
4. Piston seal
5. Disc brake piston
6. Cylinder boot
7. Disc brake inner pad
8. Disc brake outer pad
9. Brake caliper carrier
10. Pad spring
11. Bleeder plug
12. Bleeder plug cap
13. Caliper pin
14. Anti noise shim
15. Inner shim
Tightening torque
(a): 8.5 N.m (0.85 kg-m, 6.5 lb-ft)
(b): 8.0 N.m (0.80 kg-m, 6.0 lb-ft) [A]
[B]
5B-2 FRONT BRAKE
GENERAL DESCRIPTION
DISC BRAKE CALIPER ASSEMBLY
This caliper is mounted to the brake caliper carrier with two caliper pin bolts. Hydraulic force, created by applying
force to the brake pedal, is converted by the caliper to friction. The hydraulic force acts equally against the piston
and the bottom of the caliper bore to move the piston outward and to move (slide) the caliper inward, resulting in
a clamping action on the disc. This clamping action forces the pads (linings against the disc, creating friction to
stop the vehicle.
NOTE:

Lubricate parts as specified. Do not use lubricated shop air on brake parts as damage to rubber compo-
nents may result. If any component is removed or line disconnected, bleed the brake system.
Replace pads in axle sets only. The torque values specified are for dry, unlubricated fasteners.

For identification of the brake caliper type, see maker name or mark on brake caliper as shown.

YH4
GRAND
VITARA
FRONT BRAKE 5B-11
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake caliper bleeder plug
(For SUMITOMO ELECTRIC brake caliper)8.00.806.0
Brake caliper bleeder plug
(For TOKICO brake caliper)8.50.856.5
Caliper pin bolt (For TOKICO brake caliper)272.720.0
Caliper pin bolt (M10)
(For SUMITOMO ELECTRIC brake caliper)505.036.5
Caliper pin bolt (M12)
(For SUMITOMO ELECTRIC brake caliper)858.561.5
Flexible hose bolt232.317.0
Brake carrier bolt858.561.5
Wheel nut10010.072.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.

YH4
GRAND
VITARA
A-1. Color ring
A-2. Cable
A-3. Grommet
A-4. Bolt
A-5. Clamp (if equipped)A-6. Cross-member
A-7. Chassis frame
A-8. Hanger
A-9. Rear axle
A-10. G-sensor (if equipped) B-1. Parking brake switch
B-2. Parking brake lever
B-3. Parking brake lever bolt
B-4. Floor
B-5. Locking nut
B-6. Spacer
B-7. Pin
B-8. Equalizer
B-9. Adjust rod
B-10. Coupler
PARKING AND REAR BRAKE 5C-5
PARKING BRAKE CABLE
REMOVAL
1) Remove brake drum. (Refer to steps 1) to 5) of BRAKE DRUM
REMOVAL of this section.)
2) Check the color of ring or tape for reinstallation.
NOTE:
Color ring on brake cable is for the purpose of identifica-
tion.
3) Disconnect parking brake cable from brake shoe lever. (Refer to
steps 2) to 5) of BRAKE SHOE REMOVAL of this section.)
4) Disconnect brake cable from brake back plate. (Refer to step 4)
of BRAKE BACK PLATE REMOVAL.)
NOTE:
When it is necessary to remove both right and left parking
brake cables, repeat above steps 1) to 3) on right and left
wheels.
5) Remove cable from parking brake lever. (Refer to steps 1) to 5)
of PARKING BRAKE LEVER REMOVAL of this section.)

YH4
GRAND
VITARA
PARKING AND REAR BRAKE 5C-17
09943-35512
Brake drum remover
(Front wheel hub remover)09942-15510
Sliding hammer
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Wheel cylinder bleeder plug7.50.755.5
Parking brake lever bolt232.317.0
Wheel cylinder bolt (For non sealed type)8.50.856.5
Wheel cylinder bolt (For gasket sealed type)111.112.0
Brake pipe flare nut161.612.0
Brake back plate nut232.317.0
Wheel nut10010.072.5
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.
Water tight
sealantSEALING COMPOUND 366E
99000-31090
To apply to mating surfaces of brake back
plate and rear wheel cylinder.
SealantSUZUKI BOND NO. 1215
99000-31110

To apply to mating surfaces of brake back
plate and rear axle housing.

To apply mating surfaces of brake back
plate and rear wheel bearing retainer.
SPECIAL TOOLS

YH4
GRAND
VITARA
7A-14 MANUAL TRANSMISSION (TYPE 1)
09951-16060
Oil seal installer
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Oil filler / level and drain plugs232.317.0
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back up light switch (Type 1)202.014.5
Back up light switch (Type 2)454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts and nut505.036.5
Exhaust center pipe to manifold nuts505.036.5
Muffler to exhaust center pipe bolts505.036.5
Universal joint flange bolts505.036.5
Select return spring bolts232.317.0
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever.

Select return springs, bolts and guides.
Thread lock cementTHREAD LOCK CEMENT
SUPER 1333B (99000-32020)
Shift control lever locating bolts.
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil Drain and filler / level plugs.
SPECIAL TOOL

YH4
GRAND
VITARA
MANUAL TRANSMISSION (TYPE 2) 7A1-5
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN´mkg-mlb-ft
Transfer oil filler / level and drain plugs232.317.0
Transmission oil filler / level and drain plugs383.827.5
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back-up light switch454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts505.036.5
Muffler to exhaust No. 2 pipe nuts505.036.5
Universal joint flange bolts505.036.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever
Thread lock cement
THREAD LOCK CEMENT
SUPER 1333B
(99000-32020)

Shift control lever locating bolts
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil drain and filler / level plugs