2004 SUBARU OUTBACK towing

9-25
In case of emergency
– CONTINUED –
2. Press portion B and simultaneously pull the towing
hook cover toward you. 3. Turn the towing hook cover clockwise, pivoting it
about the side that is next to the fog lamp. Pull out the
towing hook cover to remove it.
UB9043BAUB9044AA

9-26
In case of emergency
T
Towing hook cover installation procedure
For except OUTBACK models:
Align the towing hook cover with its original installation
position and press all parts of it into place. For OUTBACK models:
1. Insert the projection
C into the hole D.
UB9052BA
C D
UB9044CB

9-28
In case of emergency
„
Towing with all wheels on the ground
yNever turn the ignition switch to the “LOCK”
position while the vehicle is being towed be-
cause the steering wheel and the direction of
the wheels will be locked.y Remember that the brake booster and power
steering do not function when the engine is not
running. Because the engine is turned off, it will
take greater effort to operate the brake pedal
and steering wheel.
y If transmission failure occurs, transport your
vehicle on a flat-bed truck. y Do not run the engine while being towed us-
ing this method. Transmission damage could
result if the vehicle is towed with the engine
running. y For vehicles with automatic transmission,
the traveling speed must be limited to less than
20 mph (30 km/h) and the traveling distance to
less than 31 miles (50 km). For greater speeds
and distances, transport your vehicle on a flat-
bed truck.
1. Check the transmission and differential oil levels
and add oil to bring it to the upper level if necessary.
2. Release the parking brake and put the transmis-
sion in neutral.
3. The ignition switch should be in the “ACC” position
while the vehicle is being towed.
4. Take up slack in the towline slowly to prevent dam-
age to the vehicle.UB8010AA

11 - 1 6
2Maintenance and service
API Service label
1) Indicates the oil quality by API designations
2) Indicates the SAE oil viscosity grade
3) Indicates that the oil has fuel saving capabilities
In choosing an oil, you want the proper quality and vis-
cosity, as well as one that will add to fuel economy.
The following table lists the recommended viscosities
and applicable temperatures.
When adding oil, different brands may be used togeth-
er as long as they are the same API classification and
SAE viscosity as those recommended by SUBARU. SAE viscosity number and applicable temperature
*: 5W-30 is preferred.
Engine oil viscosity (thickness) affects fuel economy.
Oils of lower viscosity provide better fuel economy.
However, in hot weather, oil of higher viscosity is re-
quired to properly lubricate the engine. „ Recommended grade and viscosity
under severe driving conditions
If the vehicle is used in desert areas, in areas with very
high temperatures, or used for heavy-duty applica-
tions such as towing a trailer, use of oil with the follow-
ing grade and viscosities is recommended.
APISERVICESL
ENERGYCONSERVING
SAE
5W
30
1
2
3
HSB022BB
5W-30*10W-30, 10W-40
-30 -20 -10 0 10 20 30 40
-20
06 0
20 80 100 40
HSB024BA

12-5
Specifications
– CONTINUED –
„Tires
„ Wheel alignment
Tire sizeP205/60R15 90HP205/55R16 89HP225/60R16 97H
Wheel size15 x 6JJ16 x 6 1
/2 JJ
PressureFront32 psi (220 kPa, 2.2 kg/cm 2
)30 psi (210 kPa, 2.1 kg/cm 2
)
Rear30 psi (210 kPa, 2.1 kg/cm 2
)29 psi (200 kPa, 2.0 kg/cm 2
)
Rear at trailer
towing–32 psi (220 kPa, 2.2 kg/cm 2
)
Temporary
spare tireSizeT135/70R16T145/80R16
Pressure60 psi (420 kPa, 4.2 kg/cm 2
)
ItemLegacyOUTBACK
SedanWagonSedanWagon
ToeFront0 in (0 mm)
Rear0 in (0 mm)
CamberFront–0 °05’0 °20’
Rear–0 °30’–0 °20’–0 °10’

13-5
Consumer information and Reporting safety defects
– CONTINUED –
„Recommended tire inflation pressure
T Recommended cold tire inflation pressure
Recommended cold tire inflation pressure for your vehicle’s tires is as follows,
Tire size P205/60R15 90H P205/55R16 89H P225/60R16 97H
Wheel size 15 x 6JJ 16 x 6 1/2JJ
Pressure Front 32 psi (220 kpa, 2.2 kg/cm 2
)3 0 p si
(210 kpa, 2.1 kg/cm 2
)
Rear 30psi (210 kpa, 2.1 kg/cm 2
)2 9 p si
(200 kpa, 2.0 kg/cm 2
)
Rear at trailer
towing –3
2 p si
(220 kpa, 2.2 kg/cm 2
)
Temporary
spare tire Size T135/70R16 T145/80R16
Pressure 60 psi (420 kpa, 4.2 kg/cm
2
)

13-9
Consumer information and Reporting safety defects
– CONTINUED –
left-hand side of the vehicle. (Each tire must be
kept on its original side of the vehicle.) Replace
any damaged or unevenly worn tire at the time of
rotation. After tire rotation, adjust the tire pres-
sures and make sure the wheel nuts are correct-
ly tightened. A tightening torque specification
and a tightening sequence specification for the
wheel nuts can be found “Flat tires” in Chapter 9. „Vehicle load limit – how to determine
The load capacity of your vehicle is determined
by weight, not by available cargo space. The
load limit of your vehicle is shown on the vehicle
placard attached to the driver’s side B-pillar. Lo-
cate the statement “The combined weight of oc-
cupants and cargo should never exceed XXX kg
or XXX lbs” on your vehicle’s placard.
The vehicle placard also shows seating capacity
of your vehicle.
The total load capacity includes the total weight
of driver and all passengers and their belong-
ings, any cargo, any optional equipment such as
a trailer hitch, roof rack or bike carrier, etc., and
the tongue load of a trailer. Therefore cargo ca- pacity can be calculated by the following method.
Cargo capacity = Load limit – (total weight of oc-
cupants + total weight of optional equipment +
tongue load of a trailer (if applicable))
For towing capacity information and weight lim-
its, refer to “Trailer towing” in Chapter 8. T
Calculating total and load capacities vary-
ing seating configurations
Calculate the available load capacity as shown in
the following examples:
Example 1A
UBD009BA

13-14
Consumer information and Reporting safety defects
„
Adverse safety consequences of over-
loading on handling and stopping and on tires
Overloading could affect vehicle handling, stop-
ping distance, vehicle and tire as shown bellow.
This could lead to an accident and possibly result
in severe personal injury. y Vehicle stability will deteriorate.
y Heavy and/or high-mounted loads could in-
crease the risk of rollover.y Stopping distance will increase.
y Brakes could overheat and fail.
y Suspension, bearings, axles and other body
parts could break or experience accelerated
wear that will shorten vehicle life. y Tires could fail.
y Tread separation could occur.
y Tire could separate from its rim.
„ Steps for Determining Correct Load
Limit
1. Locate the statement “The combined weight
of occupants and cargo should never exceed
XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver
and passengers that will be riding in your vehicle.
3. Subtract the combined weight of the driver
and passengers from XXX kilograms or XXX
pounds.
4. The resulting figure equals the available
amount of cargo and luggage load capacity. For
example, if the “XXX” amount equals 1,400 lbs
(635kg). and there will be five- 150 lbs (68 kg)
passengers in your vehicle, the amount of avail-
able cargo and luggage load capacity is 650 lbs.
(1,400 – 750 (5 x 150) = 650 lbs.)
5. Determine the combined weight of luggage
and cargo being loaded on the vehicle. That
weight may not safely exceed the available car-
go and luggage load capacity calculated in Step 4.
6. If your vehicle will be towing a trailer, load
from your trailer will be transferred to your vehi-
cle. Consult this manual to determine how this
reduces the available cargo and luggage load
capacity of your vehicle.