2004 SUBARU OUTBACK ESP

4-15
Climate control
– CONTINUED –
T – Fan speed control switch
1) Fan speed control switch
The fan speed control switch has the 5 positions:
AUTO position and 4 different fan speed positions.
With the fan speed control switch in the AUTO posi-
tion, the fan speed changes automatically correspond-
ing to various conditions: air temperature inside and
outside of the passenger compartment, intensity of the
sunlight, etc.
Use this switch to select desired fan speed. Fan speed
increases with each press of the switch and returns to
the AUTO position. T
A/C – Air conditioner switch
NOTE
The air conditioner compressor does not operate
when the outside air temperature is below 32 °F
(0 °C).
If the windshield starts to fog when the air conditioner
is operated in the AUTO mode, push the air condition-
er switch “A/C” to defog and dehumidify.
When this switch is pushed, the air conditioner com-
pressor turns on and the indicator light “A/C” on the
control panel comes on. After eliminating the fogging
from the windshield, set the air conditioner back in the
AUTO mode by pushing the “AUTO” switch. T MODE – Air flow control switch
(Ventilation): Air flows through the instrument pan-
el outlets.
(Bi-level): Air flows through the instrument panel
outlets and the foot outlets.
(Heat): Air flows through the foot outlets and
some through the windshield defroster outlets.
1
AUTO 1 2 3 4UB5021BB

5-24
Audio
NOTE
Make sure to always insert a disc with the label
side up. If a disc is inserted with the label side
down, it might be ejected or the player might shut off. T
How to insert a CD(s)
V Inserting a CD
1. Press “LOAD” button (14). If the magazine in the
player has an idle position where you can insert a disc,
the “DISC” indicator associated with the idle position
will blink.
If no indicator blinks, it means that there is no idle po- sition in the magazine.
2. As soon as the “DISC” indicator begins to blink, the
“IN” will appear on display for a period of 15 seconds.
Insert a disc during the period. The disc will be then
automatically drawn in, and the player will begin to
play back the first number of the disc. y To insert more discs in succession, repeat Steps 1
and 2. The magazine will be loaded with discs in the
ascending order of position number.
If you do not insert any disc in 15 seconds after you
have pressed the “LOAD” button, the player will begin
to play back the first number of the last disc you have
inserted. y
The disc indicator steadily lights up if a disc is al-
ready inserted in the corresponding position of themagazine. y While the player is in the loading mode, if you press
the “FM/AM” selection button (4), the player will enter
the standby mode. Press the “CD” button (11) to start
playback. V Inserting a disc in a desired position
1. Press the “LOAD” button. If the magazine in the
player has an idle position where you can insert a disc,
the “DISC” indicator associated with the idle position
will blink.
The positions in the magazine the indicator of which
steadily lights up are already loaded with discs.
2. Press the “Disc select” button (15) at the position
where you want to insert a disc. The associated
“DISC” indicator will blink, and the “IN” will be dis-
played.
3. If you insert a disc during the 15-second period
while the “IN” is on display, the disc will be automati-
cally drawn in, and the player will start playback of the
disc, beginning with the first number. y To insert more discs in succession, repeat Steps 1
and 2. y While the player is in the loading mode, if you press
the “FM/AM” selection button (4), the player will enter

5-32
Audio
wish to listen. T
Weather band button (WB)
Press the “WB” button (2) to choose weather band.
The display will show WB.
Use the tuning dial to select the station to which you
wish to listen. T Manual tuning
Turn the tuning dial (3) outer tuner to increase or de-
crease the reception frequency in individual steps.
FM band: 0.2 MHz steps
AM band: 10 kHz steps
Weather band: 1 step (1 channel)
T Seek tuning (SEEK)
If the Tuning dial (3) outer tuner is turned for longer
than half of a second, the radio will begin to automati-
cally search for receivable frequencies and will stop at
the first one found. This function may not be available,
however, when radio signals are weak. In such a situ-
ation, perform manual tuning to select the desired sta- tion. T Scan tuning (SCAN)
Press the “SCAN” button (4) to change the radio to the
SCAN mode. In this mode, the radio scans through the
radio band until a station is found. The radio will stop at the station for five seconds while displaying the fre-
quency, after which scanning will continue until the en-
tire band has been scanned.
Turn the tuning dial (3) inner tuner again to cancel the
SCAN mode and to stop on any displayed frequency.
Scan tuning may not function properly if the station re-
ception is weakened by distance from the station or
proximity to tall buildings and hills. T
Preset tuning
Press any one of the preset buttons (5) to select the
corresponding, previously-registered radio station.
The LED at the top of that button will turn on. V Manual preset
y Use the tuning dial (3) to select the radio station
which you wish to register. y Choose the preset button (5) to which you wish to
assign that station and press it continuously for a peri-
od of more than 2 seconds. When the radio station has
been successfully registered, the display will flash the
corresponding radio frequency on and off once.
NOTE y Each preset button can be used to store both an
FM station and an AM station. y If the power supply is interrupted by disconnec-
tion of the battery, memory presets will be cleared

5-35
Audio
– CONTINUED –
NOTE ySingle CDs (i.e., 8-cm/3-inch CDs) are not sup-
ported, and if inserted, they will be immediately
ejected. y Make sure to always insert a disc with the label
side up. If a disc is inserted with the label side
down, it might be ejected or the player might shut off. y If a disc is inserted during a radio broadcast, the
disc will interrupt the broadcast. y After the last song finishes, the disc will auto-
matically return to track 1 (the first song on the
disc) and will automatically play back. T How to insert a CD(s)
V Inserting a CD
1. Press “LOAD” button (12). If the magazine in the
player has an idle position where you can insert a disc,
the “DISC” indicator associated with the idle position
will blink.
If no indicator blinks, it means that there is no idle po-
sition in the magazine.
2. As soon as the “DISC” indicator begins to blink, the
“CD-IN” will appear on display for a period of 15 sec-
onds. Insert a disc during the period. The disc will be
then automatically drawn in, and the player will begin
to play back the first number of the disc. y
To insert more discs in succession, repeat Steps
1 and 2. The magazine will be loaded with discs in
the ascending order of position number.
If you do not insert any disc in 15 seconds after you
have pressed the “LOAD” button (12), the player
will begin to play back the first number of the last
disc you have inserted. y The disc indicator steadily lights up if a disc is al-
ready inserted in the corresponding position of the
magazine. y While the player is in the loading mode, if you
press “FM/AM” selection button (1), the player will
enter the standby mode. Press the “Disc” button
(15) to start playback.
V Inserting a disc in a desired position
1. Press the “LOAD” button (12). If the magazine in
the player has an idle position where you can insert a
disc, the “DISC” indicator associated with the idle po-
sition will blink.
The positions in the magazine the indicator of which
steadily lights up are already loaded with discs.
2. Press the “Disc select” button (16) at the position
where you want to insert a disc. The associated
“DISC” indicator will blink, and the “CD-IN” will be dis-
played.
3. If you insert a disc during the 15-second period
while the “IN” is on display, the disc will be automati-

5-40
Audio
y
Do not attempt to insert two or more discs
into the slot at a time. Doing so can cause me-
chanical damage to the CD changer. y Use only music CDs identified by
am ark .
y Do not use CDs listed below which could
cause damage to the CD player.
y3-inch (8 cm) compact disc.
y Any disc with a peel-off or seal on it.
y Any disc with scratches and/or dust.
y Bent disc.
y Cleaning disc.
y CD accessory. (E.g., 3-inch (8 cm) disc
adapter)
y Do not insert or remove any disc when the
automatic transmission selector lever is in the
park position; the selector lever in that position
can interfere with disc insertion or removal,
causing scratches on the disc surface (for AT
vehicles).
T To insert a disc
1. Press one of the “Disc select” buttons (3) (num-
bered from 1 to 6) for which the disc indicator light (2) is “OFF”.
The Disc indicator lights are located directly above the
corresponding “Disc select” buttons.
2. The indicator will begin blinking. The blinking will last for 15 seconds.
During this period, insert a desired disc, and the disc
will begin to play. (If any disc is not inserted during this
period, the “Disc slot” (1) door will close. Repeat step
1.)
Be sure to hold a disc with the label side (the side
where titles are printed) up.
3. To insert another disc, repeat step 1 and 2 choos-
ing a different disc select button. T
To insert six discs at a time
1. Press and hold the “Disc select” button number 1
until all disc indicators begin blinking (about 1.5 sec-
onds).
2. The indicators will blink for 15 seconds. During this
period, insert desired six discs.
3. When all discs are loaded, the first disc will begin to
play. (If no disc is inserted within this 15 seconds, the
entire disc load sequence will be canceled.) T To remove a disc
1. Press the desired one of the “Disc select” buttons
(3) (numbered from 1 to 6) for which the disc indicator
light is on.

5-41
Audio
– CONTINUED –
2. Press the “Eject button” (4). The selected disc will
be ejected and the indicator light will begin blinking.
3. To remove another disc, repeat step 1 and 2
choosing a different “Disc select” button.
(To remove discs when the ignition switch is in the
“Lock” position, press the “Eject” button, and the first
disc will be ejected. Press the “Eject” button again,
and the next disc will be ejected and so on. At this
time, the “Disc select” buttons are disabled.) TTo remove all discs at one time
1. Press and hold the “Eject” button (4) until all “Disc”
indicators begin blinking (about 1.5 seconds), and the
first disc will be ejected.
2. When the disc is removed, the next one will be
ejected, and so on. T To replace a playing disc with another
Simply press the desired one of “Disc select” buttons
(3) (numbered from 1 to 6) or press the “DISC UP” or
“DISC DOWN” button on the radio unit to select the
desired disc, and the disc will begin to play. T Disc indicators
Lit: when the corresponding storage tray is occupied
by a disc.
Blinking: Disc player is either in loading, eject or
changing mode. OFF: No disc is loaded or the ignition switch is in the
“LOCK” position. T
Function control
Refer to CD player control operating instructions de-
scribed in the “Type A and B audio set (if equipped)” section.

6-10
Interior equipment
Cigarette lighter socket (if equipped)
y
The electrical power socket located on the
lower part of the instrument panel is originally
designed to use a SUBARU genuine cigarette
lighter plug. Do not use non-genuine cigarette
lighter plugs in the socket. Doing so may cause
a short-circuit and overheating, resulting in a fire. y If the socket is ever used for a plug-in acces-
sory such as a mobile phone, they may damage
the portion of the socket’s internal mechanism
that causes a cigarette lighter plug to “pop out”
after its lighter element is heated. Therefore, do
not place a cigarette lighter plug in a socket
that has been used, even once, to power a plug-
in accessory. Doing so may cause the plug to
stick and overheat, creating a potential fire haz-
ard.y Do not place any foreign objects, especially
metal ones such as coins or aluminum foil, into
the socket. That could cause a short circuit. The electrical power socket located on the lower part
of the instrument panel can be used as cigarette light-
er socket. A cigarette lighter plug is an optional acces-
sory. It is available from your SUBARU dealer.
The cigarette lighter socket may also be used as a
power source for an in-car use electrical appliance. „
Use with a cigarette lighter
To avoid being burned, never grasp the lighter
by the end with the heating element. Doing so
could result in injury and could also damage
UB6011BA

6-18
Interior equipment
„
OnStar system limitations
Complete limitations can be found on the Subscriber
Services Agreement at www.onstar.com
.
An OnStar Service Subscription Agreement is re-
quired in order to receive OnStar services, including
OnStar Personal Calling and OnStar Virtual Advisor.
OnStar services require vehicle electrical system and
wireless service to be available and operating for fea-
tures to function properly. OnStar uses existing emer-
gency service providers as well as wireless and satel-
lite technologies.
In order to provide you with excellent service, calls
with the OnStar Center may be monitored or recorded. OnStar Service is: y available in the 48 contiguous United States, Alas-
ka, Hawaii; y available when the vehicle is within the operating
range of a cellular provider;y subject to limitations caused by atmospheric condi-
tions, such as severe weather or topographical condi-
tions, such as mountainous terrain; y subject to cellular carrier equipment limitations.
Global positioning locating capabilities will not be
available if satellite signals are obstructed. OnStar will not function if the vehicle’s battery is dis-
charged or disconnected. It may also be inoperative if
the vehicle is in an accident and the OnStar or vehicle
electrical system components are damaged.
OnStar is the communication link between you and ex-
isting governmental emergency and roadside service
providers. OnStar will receive your call and use rea-
sonable effort to contact an appropriate provider. On-
Star cannot promise that the providers will respond in
a timely manner or at all.
If metallic objects, including roof-mounted accessories
or metallic cargo within the accessory, are placed in
the immediate vicinity of the OnStar antenna, the an-
tenna’s performance will be degraded. This may pre-
vent the OnStar system from functioning properly.
Therefore, please use caution when installing roof-top
accessories to make certain that metallic accessories
or metallic objects are not placed in the immediate vi-
cinity of the antenna.