2004 SUBARU LEGACY oil viscosity

8-11
Driving tips
– CONTINUED –
Winter driving „Operation during cold weather
Carry some emergency equipment, such as tire
chains, a window scraper, a bag of sand, flares, a
small shovel, and jumper cables.
Check the battery and cables. Cold temperatures re-
duce battery capacity. The battery must be in good
condition to provide enough power for cold winterstarts.
Use an engine oil of proper grade and viscosity for
cold weather. Heavy summer oil will cause harder starting.
Keep the door locks from freezing by squirting them
with deicer or glycerin.
Forcing a frozen door open may damage or separate
the rubber weather strips around the door. If the door
is frozen, use hot water to melt the ice, and afterwards
thoroughly wipe the water away.
Use a windshield washer fluid that contains an anti-
freeze solution. Do not use engine antifreeze or other
substitutes because they may damage the paint of the
vehicle. T
Before driving your vehicle
Before entering the vehicle, remove any snow or ice
from your shoes because that could make the pedals
slippery and dangerous.
While warming up the vehicle before driving, check
that the accelerator pedal, brake pedal, and all other
controls operate smoothly.
Clear away ice and snow that has accumulated under
the fenders to avoid making steering difficult. During
severe winter driving, stop when and where it is safe
to do so and check under the fenders periodically.
UB3010AA

11 - 1
11
Maintenance and service
Ma inte nan ce sche du le .. ... ... ... .. ... ... ... ... .. ... ... 11-3
Ma in te nan ce precau tio ns ... ... .. ... ... ... ... .. ... ... 11-3
B ef ore checki ng o r servicing in th e e ngi ne
c o m part ment ..... ..................... ..................... ... 11-4
W hen y ou do c h ecking or servic ing in t h e
e ngi ne c omp artme nt while the engi ne is
r u nn ing ............... ..................... ..................... ... 11-5
En gine ho od .. ... ... ... .. ... ... ... ... ... .. ... ... ... ... .. ... ... 11-5
Engine compartment overview ................... 11-8 2.5 liter models .................................................. 11-8
2.5 liter CALIFORNIA spec models ................. 11-9
3.0 liter models .................................................. 11-10
Engine oil ...................................................... 11-11 Checking the oil level ....................................... 11-11
Changing the oil and oil filter .......................... 11-12
Recommended grade and viscosity ................ 11-15
Recommended grade and viscosity under severe driving conditions .............................. 11-16
Cooling system ............................................. 11-17 Hose and connections ...................................... 11-18
Engine coolant .................................................. 11-18
Air cleaner element ...................................... 11-22 Replacing the air cleaner element ................... 11-22
Spark plugs ................................................... 11-25 Recommended spark plugs ............................. 11-25
Drive belts ..................................................... 11-26 2.5 liter models .................................................. 11-26
3.0 liter models .................................................. 11-26
Manual transmission oil ............................... 11-27 Checking the oil level ....................................... 11-27 Recommended grade and viscosity ............... 11-27
Automatic transmission fluid ...................... 11-28 Checking the fluid level .................................... 11-28
Recommended fluid ......................................... 11-30
Front differential gear oil (AT vehicles) ...... 11-30 Checking the oil level ....................................... 11-30
Recommended grade and viscosity ............... 11-31
Rear differential gear oil ............................... 11-32 Checking the gear oil level .............................. 11-32
Recommended grade and viscosity ............... 11-34
Power steering fluid ...................................... 11-35 Checking the fluid level .................................... 11-35
Recommended fluid ......................................... 11-36
Brake fluid ..................................................... 11-36 Checking the fluid level .................................... 11-36
Recommended brake fluid ............................... 11-37
Clutch fluid (MT vehicles) ............................ 11-38 Checking the fluid level .................................... 11-38
Recommended clutch fluid .............................. 11-38
Brake booster ................................................ 11-39
Brake pedal .................................................... 11-39 Checking the brake pedal free play ................ 11-39
Checking the brake pedal reserve distance ... 11-40
Clutch pedal (Manual transmission vehicles) ............... 11-40Checking the clutch function .......................... 11-40
Checking the clutch pedal free play ............... 11-41
Replacement of brake pad and lining ......... 11-41 Breaking-in of new brake pads and linings .... 11-42

11-11
2Maintenance and service
– CONTINUED –
Engine oil „Checking the oil level
Check the engine oil level at each fuel stop.
1. Park the vehicle on a level surface and stop the en-
gine.
2. Pull out the dipstick, wipe it clean, and insert it
again.
3. Be sure the dipstick is correctly inserted until it
stops with the graphic symbol on its top appear-
ing as shown in the illustration. 1) Notch (except 3.0L)
2) Upper level
3) Lower level
4. Pull out the dipstick again and check the oil level on
it. If it is below the lower level, add oil to bring the level
up to the upper level.
Use only engine oil with the recommended
grade and viscosity.
If you check the oil level just after stopping the engine,
UBB004JA
1 2
3
UGB082BB

11 -1 5
2Maintenance and service
– CONTINUED –
„Recommended grade and viscosity
Use only engine oil with the recommended
grade and viscosity.
Oil grade:
ILSAC GF-3, which can be identified with the new
API certification mark (Starburst mark)
or API classification SL with the words “ENERGY
CONSERVING” (if you cannot obtain the oil with
SL grade, you may use SJ grade “ENERGY CON-
SERVING” oil).
These recommended oil grades can be identified by
looking for either or both of the following marks dis-
played on the oil container. New API Certification Mark (Starburst Mark)
AMERICANPETROLEUMINSTITUTE
CERTIFIED
HSB023AA

11 - 1 6
2Maintenance and service
API Service label
1) Indicates the oil quality by API designations
2) Indicates the SAE oil viscosity grade
3) Indicates that the oil has fuel saving capabilities
In choosing an oil, you want the proper quality and vis-
cosity, as well as one that will add to fuel economy.
The following table lists the recommended viscosities
and applicable temperatures.
When adding oil, different brands may be used togeth-
er as long as they are the same API classification and
SAE viscosity as those recommended by SUBARU. SAE viscosity number and applicable temperature
*: 5W-30 is preferred.
Engine oil viscosity (thickness) affects fuel economy.
Oils of lower viscosity provide better fuel economy.
However, in hot weather, oil of higher viscosity is re-
quired to properly lubricate the engine. „ Recommended grade and viscosity
under severe driving conditions
If the vehicle is used in desert areas, in areas with very
high temperatures, or used for heavy-duty applica-
tions such as towing a trailer, use of oil with the follow-
ing grade and viscosities is recommended.
APISERVICESL
ENERGYCONSERVING
SAE
5W
30
1
2
3
HSB022BB
5W-30*10W-30, 10W-40
-30 -20 -10 0 10 20 30 40
-20
06 0
20 80 100 40
HSB024BA

11 -1 7
2Maintenance and service
– CONTINUED –
API classification SL (or SJ):
SAE viscosity No.:
30, 40, 10W-50, 20W-40, 20W-50
Cooling system
Never attempt to remove the radiator cap until
the engine has been shut off and has cooled
down completely. Since the coolant is under
pressure, you may suffer serious burns from a
spray of boiling hot coolant when the cap is re-
moved.
yThe cooling system has been filled at the fac-
tory with a high quality, corrosion-inhibiting,
year-around coolant which provides protection
against freezing down to –33 °F (–36 °C). For
adding, use genuine SUBARU coolant or an
equivalent: a mixture of 50% soft water and 50%
ethylene-glycol basis coolant. Use of improper
coolants may result in corrosion in the cooling
system. It is important to maintain protection
against freezing and corrosion, even if freezing
temperatures are not expected. Never mix dif-
ferent kinds of coolant. y Do not splash the engine coolant over paint-

11 -2 7
2Maintenance and service
– CONTINUED –
Manual transmission oil „Checking the oil level
1) Yellow
1. Park the vehicle on a level surface and stop the en-
gine.
2. Pull out the dipstick, wipe it clean, and insert it
again. 1) Upper level
2) Lower level
3. Pull out the dipstick again and check the oil level on
it. If it is below the lower level, add oil through the dip-
stick hole to bring the level up to the upper level. „ Recommended grade and viscosity
Each oil manufacturer has its own base oils and addi-
tives. Never use different brands together.
Oil grade:
API classification GL-5
1
UBB004DB
1 2
OM-U0210

11 -3 1
2Maintenance and service
– CONTINUED –
1) Upper level
2) Lower level
3. Pull out the dipstick again and check the oil level on
it. If it is below the lower level, add oil to bring the level
up to the upper level. „ Recommended grade and viscosity
Each oil manufacturer has its own base oils and addi-
tives. Never use different brands together.
Oil grade:
API classification GL-5 SAE viscosity No. and Applicable Temperature
L
F
1 2
HSB040BB
-30 -20 -10 0 10 20 30 40
-20 0 60 20
80W
75W/90 80 100
40
85W 90
HSB036BA