2004 SUBARU LEGACY brake light

11 - 4 2
2Maintenance and service
when the brake pedal is applied.
If you hear this scraping noise each time you apply the
brake pedal, have the brake pads serviced by your
SUBARU dealer as soon as possible. „
Breaking-in of new brake pads and lin- ings
When replacing the brake pad or lining, use only gen-
uine SUBARU parts. After replacement, the new parts
must be broken in as follows: T Brake pad and lining
While maintaining a speed of 30 to 40 mph (50 to 65
km/h), step on the brake pedal lightly. Repeat this five
or more times. T Parking brake lining
A safe location and situation should be select-
ed for break-in driving.
Pulling the parking brake lever too forcefully may cause the rear wheels to lock. To avoid
this, be certain to pull the lever up slowly and
gently.
1. Drive the vehicle at a speed of about 22 mph (35 km/h).
2. With the parking brake release button pushed in,
pull the parking brake lever SLOWLY and GENTLY.
(Pulling with a force of approximately 33 lbs [147 N, 15 kg].)
3. Drive the vehicle for about 220 yards (200 meters)
in this condition.
4. Wait 5 to 10 minutes for the parking brake to cool
down. Repeat this procedure.
5. Check the parking brake stroke. If the parking
brake stroke is out of the specified range, adjust it by
turning the adjusting nut located on the parking brake
lever.
Parking brake stroke:
7 – 8 notches / 44 lbs (196 N, 20 kg)

11 - 6 4
2Maintenance and service
Wattage Bulb No.
1) Headlight GT and OUTBACK
modelsLow beam 12V-55W H1
High beam 12V-60W 9005 (HB3)
Except GT and OUT-
BACK models 12V-65/
55W9007(HB5)
2) Front turn signal 12V-27W 1156NA (Amber)
3) Spot light 12V-8W –
4) Dome light 12V-8W –
5) Door step light 12V-3.4W –
6) Front turn signal light/park- ing and front side marker
light 12V-27/8W 1157NA
(Amber)
7) Front fog light Except OUTBACK 12V-55W H3
OUTBACK 12V-51W 9006 (HB4)
8) Backup light
Sedan 12V-27W 3156K
Station wagon 12V-27W 1156
9) Luggage area light 12V-13W 912 10) High mount stop light
Sedan 12V-16W 921
Station wagon 12V-13W 912
11) Rear turn signal light Sedan 12V-21W –
Station wagon 12V-21W 7440
12) Brake/tail light Sedan 12V-27/8W 3157K
Station wagon 12V-27/8W 1157
13) License plate light
Sedan 12V-5W 168
Station wagon 12V-3.8W or 5W194 or 168
14) Trunk room light 12V-5W W5W Wattage Bulb No.

11 -7 1
2Maintenance and service
– CONTINUED –
„Rear combination lights
T Sedan
1. Open the trunk lid.
2. Open the rear combination light cover. For covers on the trunk lid:
1) Back-up light bulb
2) Brake/tail light bulb
Unlatch the cover by pushing the knob and open the cover.
UBF014DA
1
2
UBB034BC

11 - 7 2
2Maintenance and service
For covers on the trunk wall:
1) Brake/tail light bulb
2) Rear turn signal light bulb
Unlatch the cover by moving the knob upward and
open the cover.
3. Remove the bulb socket from the light assembly by
turning it counterclockwise.
4. Remove the bulb from the socket.
Rear turn signal light: Remove the bulb from the
socket by pushing it and turning it counterclockwise.
Others: Pull the bulb out of the socket.
5. Install a new bulb in the socket.
6. Set the bulb socket into the rear combination light assembly and turn it clockwise until it locks.
7. Close the cover and latch the clock. T
Station wagon
V Brake/tail and rear turn signal light bulbs
It may be difficult to replace the bulbs. It is recom-
mended that you have the bulbs replaced by yourSUBARU dealer.
1) Service holes
1. Remove the light bulb replacement service hole
covers at two places by prying the edge of the cover
with a regular screwdriver.
1
2
UBB035BB1
UBB021BB

11 -7 3
2Maintenance and service
– CONTINUED –
1) Nuts
2. Remove the upper and lower nuts. Then, slide the
rear combination lamp assembly to the rear and re-
move it from the vehicle.
3. Using a Phillips screwdriver, remove the upper and
lower screws that secure the side cover of the rear
combination light assembly. 1) Rear turn signal light bulb
2) Brake/tail light bulb
4. Remove the bulb socket from the rear combination
light assembly by turning it counterclockwise.
1
UBB022BB
1
2
UBB070BB

11 - 7 4
2Maintenance and service
Turn signal light bulb
Brake/tail light bulb
5. Remove the bulb from the socket.
Turn signal light: Pull the bulb out of the socket.
Brake/tail light: Remove the bulb from the socket by
pushing it and turning it counterclockwise.
6. Install a new bulb in the socket.
7. Set the bulb holder into the rear combination light
assembly and turn it clockwise until it locks.
8. Using a Phillips screwdriver, install the side cover
to the rear combination light assembly.
9. Fit the rear combination light assembly into the ve-
hicle body and tighten the nuts from the interior of thevehicle.
UBB048BAUBB025BA

11 -7 5
2Maintenance and service
– CONTINUED –
10.Reinstall the light bulb replacement service hole covers. VBack-up and brake/tail light bulbs
1) Back-up light bulb
2) Brake/tail light bulb
1. Unlatch the rear finisher light cover by moving the
knob upward. Open the cover up.
2. Remove the bulb socket from the rear finisher light
assembly by turning it counterclockwise. 3. Remove the bulb from the socket by pushing it and
turning counterclockwise. Install a new bulb in the socket.
4. Set the bulb holder into the rear finisher light as-
sembly and turn it clockwise until it locks.
5. Close the cover and latch the lock.
1
2
UBB026BC
UBB025BA

12-7
Specifications
– CONTINUED –
T3.0 liter models
1210AyIllumination brightness
control
1315AyFuel pump
1410AyRear window wiper and
washer
1530AyWindshield wiper and
washer
1620AyBrake light
1715AyAir conditioner
1815AyBackup light
y Cruise control
y ABS control
1920AyWiper deicer
2020AyAccessory power sock- et
y Seat heater
2115AyIgnition coil and ignitor
(CALIFORNIA spec vehicle only)
Fuse panelFuse ratingCircuit
Fuse panelFuse ratingCircuit
115AyHeater fan
19
18
17
16
21
20
15
14
12
11
10 9
8
7
6
5
4
3
2
1
13
UBC001CB