2004 SUBARU LEGACY lock

1-3
Seat, seatbelt and SRS airbags
– CONTINUED –
restrained or improperly restrained. Because
children are lighter and weaker than adults,
their risk of being injured from deployment is
greater. For that reason, we strongly recom-
mend that ALL children (including those in
child seats and those that have outgrown child
restraint devices) sit in the REAR seat properly
restrained at all times in a child restraint device
or in a seatbelt, whichever is appropriate for the
child’s age, height and weight.
Secure ALL types of child restraint devices (in-
cluding forward facing child seat) in the REAR
seats at all times.
NEVER INSTALL A REARWARD FACING CHILDSEAT IN THE FRONT SEAT. DOING SO RISKS
SERIOUS INJURY OR DEATH TO THE CHILD
BY PLACING THE CHILD’S HEAD TOO CLOSE
TO THE SRS AIRBAG.
According to accident statistics, children are
safer when properly restrained in the rear seat-
ing positions than in the front seating posi-
tions. For instructions and precautions con-
cerning child restraint systems, see the “Child
restraint systems” section in this chapter. „
Fore and aft adjustment
T Manual type
Pull the lever upward and slide the seat to the desired
position. Then release the lever and move the seat-
back and forth to make sure that it is securely locked
into place.
UB1058BA

1-6
Seat, seatbelt and SRS airbags
T
Manual type
Pull the reclining lever up and adjust the seatback to
the desired position. Then release the lever and make
sure the seat is securely locked into place.
The seatback placed in a reclined position can spring
back upward with force when released. When operat-
ing the reclining lever to return the seatback, hold it
lightly so that it may be raised back gradually. T
Power seat (if equipped)
To adjust the angle of the seatback, move the control switch.
NOTE
While adjusting the seatback, you can not at the
same time adjust the seat position or the seat
cushion angle and height.
UB1072BAUB1084BA

1-15
Seat, seatbelt and SRS airbags
– CONTINUED –
1. Lower the headrests.
2. Unlock the seatback by pulling the release knob
and then fold the seatback down. TFolding down the seat cushion and seatback
1. Move the front seat forward.
2. Close the rear passengers’ cup holder and ashtray.
3. Remove the headrests (if so equipped).
Window-side seating positions: Pull the headrest
up while pressing the release button located on the
backside of the seatback. Center seating position:
Pull the headrest up while
pressing the release button located on the top of the
seatback.
UB1096BA
UB1099CA

1-17
Seat, seatbelt and SRS airbags
– CONTINUED –
6. Unlock the seatback by pulling the release knob
and fold the seatback down. Confirm that the pin locat-
ed at the bottom of the seat cushion is inserted into the
slot at the top of the seatback. 7. Install the headrests (if so equipped) onto the back-
side of the seatback (window-side positions only).
To return the rear seat to its original position, raise the
seatback and seat cushion until they lock into place
and make sure that they are securely locked.
Make sure that the rear seatbelts are not under the
seat cushion or seatback.
Place the headrests (if so equipped) back in their nor-
mal position.
UB1027BAUB1098BA

1-19
Seat, seatbelt and SRS airbags
– CONTINUED –
TInfants or small children
Use a child restraint system that is suitable for your ve-
hicle. See information on “Child restraint systems” inthis chapter. T Children
If a child is too big for a child restraint system, the child
should sit in the rear seat and be restrained using the
seatbelts. According to accident statistics, children are
safer when properly restrained in the rear seating po-
sitions than in the front seating positions. Never allow
a child to stand up or kneel on the seat.
If the shoulder portion of the belt crosses the face or
neck, move the child closer to the belt buckle to help
provide a good shoulder belt fit. Care must be taken to
securely place the lap belt as low as possible on the
hips and not on the child’s waist. If the shoulder portion
of the belt cannot be properly positioned, a child re-
straint system should be used. Never place the shoul-
der belt under the child’s arm or behind the child’sback. T
Expectant mothers
Expectant mothers also need to use the seatbelts.
They should consult their doctor for specific recom-
mendations. The lap belt should be worn securely and
as low as possible over the hips, not over the waist. „ Emergency Locking Retractor (ELR)
The driver’s seatbelt has an Emergency Locking Re- tractor (ELR).
The emergency locking retractor allows normal body
movement but the retractor locks automatically during
a sudden stop, impact or if you pull the belt very quick-
ly out of the retractor.
HS1107AA

1-20
Seat, seatbelt and SRS airbags
„
Automatic/Emergency Locking Retrac- tor (A/ELR)
Each passenger’s seatbelt has an Automatic/Emer-
gency Locking Retractor (A/ELR). The Automatic/
Emergency Locking Retractor normally functions as
an Emergency Locking Retractor (ELR). The A/ELR
has an additional locking mode “Automatic Locking
Retractor (ALR) mode” intended to secure a child re-
straint system. When the seatbelt is once drawn out
completely and is then retracted even slightly, the re-
tractor locks the seatbelt in that position and the seat-
belt cannot be extended. As the belt is rewinding,
clicks will be heard which indicate the retractor func-
tions as ALR. When the seatbelt is retracted fully, ALR
mode is released.
When securing a child restraint system on the passen-
gers’ seats, the seatbelt must be changed over to the
Automatic Locking Retractor (ALR) mode.
When the child restraint system is removed, make
sure that the retractor is restored to the Emergency
Locking Retractor (ELR) function by allowing the seat-
belt to retract fully.
For instructions on how to convert the retractor to the
ALR mode and restore it to the ELR mode, see the
“Child restraint systems” section in this chapter. „
Seatbelt warning light and chime
Your vehicle is equipped with a seatbelt warning de-
vice at the driver’s seat.
This device causes the seatbelt warning light on the
instrument panel to light up for about six seconds
when the ignition switch is turned to the “ON” position
to remind the driver to wear the seatbelt. If the driver’s
seatbelt is not fastened, a warning chime sounds at
the same time. „ Fastening the seatbelt
yNever use a belt that is twisted or reversed. In
an accident, this can increase the risk or sever-
ity of injury.y Keep the lap belt as low as possible on your
hips. In a collision, this spreads the force of the
lap belt over stronger hip bones instead of
across the weaker abdomen.y Seatbelts provide maximum restraint when
the occupant sits well back and upright in the
seat. To reduce the risk of sliding under the
seatbelt in a collision, the front seatbacks
should be always used in the upright position
while the vehicle is running. If the front seat-

1-22
Seat, seatbelt and SRS airbags
more slowly. If the belt still cannot be unlocked, let the
belt retract slightly after giving it a strong pull, then pull
it out slowly again.
4. Insert the tongue plate into the buckle until you
hear a click.
5. To make the lap part tight, pull up on the shoulder
belt.
6. Place the lap belt as low as possible on your hips,
not on your waist.
HS1050BA
HS1051BA

1-23
Seat, seatbelt and SRS airbags
– CONTINUED –
VAdjusting the front seat shoulder belt anchor
height
The shoulder belt anchor height should be adjusted to
the position best suited for you. To lower the anchor
height, push the release button and slide the anchor
down. To raise the anchor height, slide the anchor up.
Pull down on the anchor to make sure that it is locked
in place.
Always adjust the anchor height so that the shoulder
belt passes over the middle of the shoulder without
touching the neck.
When wearing the seatbelts, make sure the
shoulder portion of the webbing does not pass
over your neck. If it does, adjust the seatbelt an-
chor to a lower position. Placing the shoulder
belt over the neck may result in neck injury dur-
ing sudden braking or in a collision.
V Unfastening the seatbelt
Push the button on the buckle.
Before closing the door, make sure that the belts are
HS1052BA
HS1053BA