2004 SUBARU LEGACY lock

11 -5 7
2Maintenance and service
– CONTINUED –
4. Align the claws of the plastic support with the
grooves in the blade rubber assembly, then slide the
blade rubber assembly into place. Securely lock the end of the plastic support as shown
in the illustration. If the rubber is not retained properly,
the wiper may scratch the rear window glass.
USB586CAUSB584BA

11 - 6 0
2Maintenance and service
1) Fuse puller
2) Spare fuses
The fuse puller and spare fuses are stored in the main
fuse box cover in the engine compartment. A) Good
B) Blown
If any lights, accessories or other electrical controls do
not operate, inspect the corresponding fuse. If a fuse
has blown, replace it.
1. Turn the ignition switch to the “LOCK” position and
turn off all electrical accessories.
2. Remove the cover.
(For behind the coin tray: open the coin tray and pull it
horizontally to remove it.)
3. Determine which fuse may be blown. The back side
of each fuse box cover and the “Fuses and circuits”
section in chapter 12 in this manual show the circuit for
1
2
HSB066BB
AB
HSB067BB

11 - 6 6
2Maintenance and service
1) Low beam light bulb
2) High beam light bulb
Remove the headlight bulb cover, by turning it coun-
terclockwise. V
Low beam light bulbs
0
1) Electrical connector
2) Red cable
3) Black cable
1. Disconnect the electrical connector for the black
cable.
1
2
UBB040BB
1 2
3
UBB041BB

11 - 6 8
2Maintenance and service
1) Push
1. Disconnect the electrical connector from the bulb.
2. Remove the bulb from the headlight assembly by
turning it counterclockwise.
3. Replace the bulb with new one.
4. Reconnect the electrical connector. At this time,
use care not to touch the bulb surface.
5. To install the bulb to the headlight assembly, turn it
clockwise until it clicks.
6. Install the headlight bulb cover. T
Except GT and OUTBACK models
1) Electrical connector
2) Push
1. Disconnect the electrical connector while pressing
the lock release tab.
1
UBB044BB
1
2
UBB045BB

11 -6 9
2Maintenance and service
– CONTINUED –
2. Remove the bulb holder from the headlight assem-
bly by turning it counterclockwise.
3. Remove the bulb from the headlight assembly.
4. Install the new bulb.
5. Install the bulb holder in the headlight assembly by
turning it clockwise until it locks.
6. Remove the electrical connector. „Front fog light (if equipped)
It may be difficult to replace the bulbs. Have your
SUBARU dealer replace the bulbs if necessary. „
Front turn signal light, parking light
and side marker light
The headlight assembly must be removed before the
front turn signal light and parking light bulbs can be re-
placed. When the headlight assembly has been re-
moved and then reinstalled, it may become necessary
to make a headlight aiming adjustment. After a bulb
has been replaced, it is recommended that the head-
light aiming adjustment be made at a SUBARU dealer.
1. Remove the headlight assembly mounting screws
located at the top of and the front of the headlight as-
sembly using a phillips screwdriver or an open-end
wrench.
UBB046BA
UBB016BA

11 - 7 0
2Maintenance and service
2. Move the headlight assembly forward.
1) Front turn signal light bulb
2) Front turn signal light bulb/parking and front side marker light bulb
3. Remove the bulb socket from the headlight assem-
bly by turning it counterclockwise. 4. Remove the bulb from the socket by pushing it and
turning counterclockwise. Install a new bulb in the
socket.
5. Set the bulb socket into the headlight assembly and
turn it clockwise until it locks.
6. Set the headlight assembly into the vehicle body.
Tighten the mounting screws.
1
2
UBB039CB
UBB020BA

11 - 7 2
2Maintenance and service
For covers on the trunk wall:
1) Brake/tail light bulb
2) Rear turn signal light bulb
Unlatch the cover by moving the knob upward and
open the cover.
3. Remove the bulb socket from the light assembly by
turning it counterclockwise.
4. Remove the bulb from the socket.
Rear turn signal light: Remove the bulb from the
socket by pushing it and turning it counterclockwise.
Others: Pull the bulb out of the socket.
5. Install a new bulb in the socket.
6. Set the bulb socket into the rear combination light assembly and turn it clockwise until it locks.
7. Close the cover and latch the clock. T
Station wagon
V Brake/tail and rear turn signal light bulbs
It may be difficult to replace the bulbs. It is recom-
mended that you have the bulbs replaced by yourSUBARU dealer.
1) Service holes
1. Remove the light bulb replacement service hole
covers at two places by prying the edge of the cover
with a regular screwdriver.
1
2
UBB035BB1
UBB021BB

11 -7 3
2Maintenance and service
– CONTINUED –
1) Nuts
2. Remove the upper and lower nuts. Then, slide the
rear combination lamp assembly to the rear and re-
move it from the vehicle.
3. Using a Phillips screwdriver, remove the upper and
lower screws that secure the side cover of the rear
combination light assembly. 1) Rear turn signal light bulb
2) Brake/tail light bulb
4. Remove the bulb socket from the rear combination
light assembly by turning it counterclockwise.
1
UBB022BB
1
2
UBB070BB