2004 SUBARU LEGACY light

7-37
Starting and operating
– CONTINUED –
yThis light turns on to indicate that the VDC system
is in non-operation mode. This does not constitute fail- ure of the VDC system.
NOTE y The VDC OFF indicator light may stay on for a
while after the engine has been started, especially
in cold weather. This occurs because the engine
has not yet warmed up and is completely normal.
The light will turn off when the engine has reached
a suitable operating temperature. y When an engine problem occurs and the CHECK
ENGINE warning light turns on, the VDC OFF indi-
cator light will also turn on.
The following two situations could indicate malfunction
of the VDC system; if either should occur, have an au-
thorized SUBARU dealer carry out an inspection of
that system at the first available opportunity. y The VDC OFF indicator light does not turn on when
the ignition key is turned to the ON position. y The VDC OFF indicator light fails to turn off after the
engine is started, even when several minutes have
passed to allow the engine to heat up sufficiently. T VDC operation indicator light
The VDC operation indicator light turns on when the
ignition key is turned to the ON position; it turns off ap- proximately two seconds later. This indicator light
flashes during activation of the skid suppression func-
tion and is illuminated steadily during activation of the
traction control function.
The following two situations could indicate a malfunc-
tion of the VDC system; if either should occur, have an
authorized SUBARU dealer carry out an inspection of
that system at the first available opportunity.y
The VDC operation indicator light does not turn on
when the ignition key is turned to the ON position.y The VDC operation indicator light does not turn off
approximately two seconds after the ignition key has
been turned to the ON position. T V D C w a r n i n g l i g h t
The VDC warning light turns on when the ignition key
is turned to the ON position and off when the engine is
started. This lighting pattern indicates that the VDC
system is operating normally.
The following situations could indicate a malfunction of
the VDC system; if any should occur, have an autho-
rized SUBARU dealer carry out an inspection of the
system at the first available opportunity. y The VDC warning light does not turn on when the ig-
nition key is turned to the ON position. y The VDC warning light does not turn off either when
the engine is started or when the vehicle reaches a

7-38
Starting and operating
speed of approximately 8 mph (12 km/h). y
The VDC warning light turns on while the vehicle is
being driven. y When a malfunction has occurred in the VDC elec-
trical system, only the VDC warning light will turn on.
In such an event, the ABS will still be operating nor-
mally. y The VDC warning light will also turn on when a prob-
lem occurs with the ABS or VDC electronic control
systems.
Because the VDC system controls each brake throughthe ABS, whenever the ABS stops operating due to a
malfunction in that electrical system, the VDC will also
become unable to control all four brakes. Thus VDC
system operation halts and the VDC warning light
turns on. Although both the VDC system and the ABS
will be inoperable in this situation, it will still be possi-
ble to stop the vehicle using normal braking. The VDC
system and the ABS do not adversely affect operation
of the vehicle in any way when they are inoperable;however should such a situation occur, drive with care
and have an authorized SUBARU dealer carry out an
inspection of those systems at the first available op-
portunity.
NOTE
When the VDC warning light turns on and off in the
following way, it indicates that the VDC system is operating normally.y
Although turning on after the engine has been
started, the warning light quickly turns off and
stays off. y The warning light turns on after the engine is
started and does not turn off until the vehicle
reaches a speed of 8 mph (12 km/h). y The warning light turns on when the vehicle is
being driven; it then turns off and stays off. „ VDC OFF switch
UB7022AA

7-39
Starting and operating
– CONTINUED –
With OnStar® System
Note: Even when the lighting switch is turned to the
“ ” or “ ” position, the “OFF” portion of the
symbol stamped on the switch will not illuminate in the
dark. Only “VDC” portion will illuminate.
Pressing the VDC OFF switch to deactivate the VDC
system can facilitate the following operations: y a standing start on a steeply sloping road with a
snowy, gravel-covered, or otherwise slippery surface y extrication of the vehicle when its wheels are stuck
in mud or deep snow
When the VDC OFF switch is pressed during engine operation, the VDC OFF indicator light illuminates.
The VDC system will be deactivated and the vehicle
will behave like a model not equipped with the VDC system.
When the VDC OFF switch is pressed again to reacti-
vate the VDC system, the VDC OFF indicator light
goes off.
If the vehicle reaches a speed of approximately 37
mph (60 km/h) after the VDC OFF switch is pressed to
deactivate the VDC system, the VDC system automat-
ically reactivates itself and the VDC OFF indicator light
goes off. While the vehicle is moving at a speed of ap-
proximately 37 mph (60 km/h) or higher, it is not pos-
sible to deactivate the VDC system by pressing theVDC OFF switch.
With the VDC system deactivated, traction and stabil-
ity enhancement offered by VDC system is unavail-
able. Therefore you should not deactivate the VDC
system except under above-mentioned situations.
NOTE y
When the VDC switch has been pressed to deac-
tivate the VDC system, the VDC system automati-
cally reactivates itself the next time the ignition
key is turned to the OFF position and the engine is
restarted. y If the VDC OFF switch is held down for 10 sec-
onds or longer, the VDC OFF indicator light goes
UB7028AA

7-41
Starting and operating
– CONTINUED –
make sure that the parking brake has been fully
released.
To set the parking brake, press the brake pedal firmly
and hold it down while fully pulling up the parking
brake lever.
To release the parking brake, pull the lever up slightly,
press the release button, then lower the lever while
keeping the button pressed.
When the parking brake is set while the engine is run-
ning, the parking brake warning light comes on. After
starting the vehicle, be sure that the warning light has
gone out before the vehicle is driven. Refer to the “Warning and indicator lights” section (chapter 3).
When parking your vehicle, always set the parking
brake firmly and put the shift lever in the “1” (1st) for an
upgrade or “R” (Reverse) for a downgrade for manual
transmission vehicles, or in the “P” (Park) position for
automatic transmission vehicles. Always set the park-
ing brake firmly when parking your vehicle. Never rely
on the transmission alone to hold the vehicle.
When parking on a hill, always turn the steering wheel.
When the vehicle is headed up the hill, the front
wheels should be turned away from the curb.
UB4001BA
UB4014AA

7-43
Starting and operating
– CONTINUED –
„To set cruise control0
Main switch Cruise control lever
1. Push the “CRUISE” main switch. The indicator light
on the switch will come on.
2. Depress the accelerator pedal until the vehicle
reaches the desired speed.
3. Push the control lever downward in the “SET,
COAST” direction and release it. Then release the ac-
celerator pedal.
The vehicle will maintain the desired speed.
UB7038BA
ACC RES
CANCEL SET
COAST
HS7018BA

7-44
Starting and operating
At this time, the “ ” indicator light is illuminated in
the combination meter.
The vehicle will maintain the desired speed.
Vehicle speed can be temporarily increased while
driving with the cruise control activated. Simply de-
press the accelerator pedal to accelerate the vehicle.
When the accelerator pedal is released, the vehicle
will return to and maintain the previous cruising speed. „
To temporarily cancel the cruise con- trol
There are four ways to cancel the cruise control tem-
porarily: y
Depress the brake pedal.
y Pull the control lever in the “CANCEL” direction. (if
so equipped) y Depress the clutch pedal (manual transmission ve-
hicles only). y Shift the selector lever into the “N” position (auto-
matic transmission vehicles only).
The “ ” indicator light in the combination meter
goes off when the cruise control is cancelled.
To resume the cruise control after it has been tempo-
rarily canceled and with vehicle speed of about 20
mph (32 km/h) or more, push the control lever upward
in the “ACCEL, RESUME” direction to return to the
original cruising speed automatically.
The “ ” indicator light in the combination meter
will automatically come on at this time. „ To turn off the cruise control
There are two ways to turn off the cruise control: y Push the main switch again.
y Turn the ignition switch to the “ACC” position (but
only when the vehicle is completely stopped).
UB4010KA

8-10
Driving tips
y
Always check your brakes for effectiveness immedi-
ately after driving in sand, mud or water. Do this by
driving slowly and stepping on the brake pedal. Re-
peat that process several times to dry out the brake
discs and brake pads.y Do not drive or park over or near flammable materi-
als such as dry grass or fallen leaves, as they may
burn easily. The exhaust system is very hot while the
engine is running and right after engine stops. This
could create a fire hazard. y After driving through tall grass, mud, rocks, sand,
rivers, etc., check that there is no grass, bush, paper,
rags, stones, sand, etc. adhering to or trapped on the
underbody. Clear off any such matter from the under-
body. If the vehicle is used with these materials
trapped or adhering to the underbody, a mechanical
breakdown or fire could occur.y Secure all cargo carried inside the vehicle and make
certain that it is not piled higher than the seatbacks.
During sudden stops or jolts, unsecured cargo could
be thrown around in the vehicle and cause injury. Do
not pile heavy loads on the roof. Those loads raise the
vehicle’s center of gravity and make it more prone totip over. y If you must rock the vehicle to free it from sand or
mud, depress the accelerator pedal slightly and move
the selector lever back and forth between “D” and “R” repeatedly. Do not race the engine. For the best pos-
sible traction, avoid spinning the wheels when trying to
free the vehicle. y
When the road surface is extremely slippery, you
can obtain better traction by starting the vehicle with
the transmission in 2nd than 1st (both for MT and AT). y Never equip your vehicle with tires larger than those
specified in this manual. y Wash the vehicle’s underbody after off-road driving.
Suspension components are particularly prone to dirt
buildup, so they need to be washed thoroughly.y Frequent driving of an AWD vehicle under hard-driv-
ing conditions such as rough roads or off roads will ne-
cessitate more frequent replacement of engine oil,
brake fluid and transmission oil than that specified in
the maintenance schedule described in the “Warranty
and Maintenance Booklet”.
Remember that damage done to your SUBARU while
operating it off-road and not using common sense pre-
cautions such as those listed above is not eligible for
warranty coverage.

8-16
Driving tips
models
Driving on snowy grades or icy roads may require the
use of tire chains, in which case put the chains on the
front wheels only. Use only SAE class S type chains
that are of the correct size for your tires so as not to
damage the vehicle body or suspension.
When driving with tire chains, drive at speeds below
19 mph (30 km/h). When a temporary spare tire is on
a front wheel, replace the temporary spare tire with the
rear tire on the same side of the vehicle, and then fit
chains on the front tires.
Always use the utmost care when driving with tire
chains – overconfidence because you are driving with
tire chains could easily lead to a serious accident. „ Rocking the vehicle
If you must rock the vehicle to free it from snow, sand,
or mud, depress the accelerator pedal slightly and
move the selector lever back and forth between “D”
and “R” repeatedly. Do not race the engine. For the
best possible traction, avoid spinning the wheels when
trying to free the vehicle.
When the road surface is extremely slippery, you can
obtain better traction by starting the vehicle with the transmission in 2nd than 1st (both for MT and AT).
Refer to the “Automatic transmission” section in chap-
ter 7 for information on holding the transmission in 2nd position.