2004 SKODA OCTAVIA TOUR lock
[x] Cancel search: lockPage 165 of 189
164DO-IT-YOURSELFFit the car jack onto the car. Recesses
are provided on the lower sill (at the front
and rear). Below this is the point at which
the car jack should be positioned - see ar-
rows in the illustration.
Position the car jack so that its claw fits
around the web of the lower sill A and the
moving base plate of the car jack B is posi-
tioned flat on the ground.
Warning
Always raise the vehicle with the
doors closed - risk of injury.
Take suitable measures to prevent
the base of the lifting jack from slip-
ping off - risk of injury!
Place the lifting jack only on a
solid and even surface.
Not positioning the lifting jack at
the specified points can result in
damage to the vehicle. In addition,
the jack may slip off if it does not
have sufficient grip - risk of injury!
Never start the engine if the vehi-
cle is lifted - risk of accident.
Never lie under the vehicle if the
vehicle is only lifted with the vehicle
lifting jack.
It is important to support the ve-
hicle with suitable supporting blocks
if you wish to work under the lifted
vehicle - risk of injury! -
If the surface is soft, place a large
solid base below the foot of the jack.
- Rotate the crank to raise the claws of the jack sufficiently so that the jack can just
still be fitted below the car.
- The claw of the jack must be fitted around the vertical web of the lower sill
so that the jack cannot slip off when the
car is raised.
- The base of the jack should be resting fully on a firm surface.
- Align jack and at the same time raise the claw of the jack further until the claw is
touching the web.
Page 166 of 189
165
DO-IT-YOURSELF
Jack up car until the wheel is just clear
of the ground.
Remove wheel bolts (after slackening)
1),
place them down on a clean surface (cloth,
paper, wheel cap) next to the car jack and
take off wheel.
Fit on spare wheel and attach wheel
bolts
1).
Tighten all the wheel bolts slightly. The
wheel bolts should be clean and turn freely.
On no account grease or oil them!
Lower car and tighten the wheel bolts
diagonally.
Press on the full wheel trim* first at the
valve opening and then apply pressure
around the entire circumference so that the
trim locks in position.
1)In order to accelerate the screwing out and in,
use the handle part of the screwdriver from the
car tool kit, which has on its end a hexagon
socket for the screw head.
Place the wheel removed in the spare
wheel well and secure with the handwheel.
Notes
After changing a wheel, pay attention to
the following points:
- Check the inflation pressure of the spare wheel fitted.
- Have the tightening torque of the wheel bolts checked with a torque wrench as
soon as possible. The tightening torque
for steel and light alloy wheels is 120 Nm.
Have the faulty wheel repaired as quickly
as possible. Warning
In case of incorrect treatment of the
wheel bolts, the wheel can loosen
when the car is moving - risk of acci-
dent!
Wheel bolts must be clean and must
turn easily. However
, they must never
be treated with grease or oil.
If the wheel bolts are tightened to a
too low tightening torque, the trims
can loosen when the car is moving -
risk of accident! A tightening torque,
which is too high, can damage the
bolts and threads and this can result
in permanent deformation of the con-
tact surfaces on the trims.
If it is intended to subsequently fit
wheels or tyres other than the factory-
fitted versions to the car, it is essen-
tial to read the remarks on page 156.
Page 167 of 189
166DO-IT-YOURSELF
Pull off the wheel caps and fit adapter B
onto the wheel bolt A. Turn adapter until
the splines engage.
Slacken or tighten the wheel bolt by fit-
ting the wheel wrench to the hexagon of the
adapter.
After removing the adapter, fit a protec-
tive cap onto the wheel bolt.
Note
It is essential that the locking bolt is tight-
ened to a torque of 120 Nm . If this torque
is exceeded, the bolt and the adapter may
in certain circumstances be damaged.
On steel wheels, the theft-deterrent
wheel bolt must always be installed in the
hole, which is close to the valve. Otherwise
the full wheel trim cannot be mounted and
the full wheel trim can be damaged during
the assembly.
You can also obtain the wheel lock bolt
set as a Genuine Accessory from your
Škoda dealer.
Anti-theft lock of wheels*Wheel locking bolts
A - Wheel bolt
B - Adapter
If wheel locking bolts are fitted to a car (one
bolt for each wheel), these can only be
slackened and tightened using the adapter
supplied. It is good practice to note the code
No. indicated on the adapter.
If the adapter or the wheel locking bolt is
lost, contact your Škoda Dealer.
Fire extinguisher*The fire extinguisher is located in the holder
below the driver seat and is secured with
straps.
Carefully read the instructions regarding
the fire extinguisher.
The fire extinguisher must be inspected
once a year by a regular person or a com-
pany. Please pay attention to the different
legal regulations.
The fire extinguisher is only delivered in
certain countries.
Pay attention to the expiration date of the
fire extinguisher. If the fire extinguisher is
used after the expiration date, its proper
function is no longer assured.
Page 169 of 189
168DO-IT-YOURSELFFuse assignment
No. Electrical component A
1 - Mirror and spray nozzle heater,relay for cigarette lighter
el. seats ........................................ 10
2 - Turn signal lights .......................... 10
3 - Stowage compartment light ............ 5
4 - Licence plate lights ......................... 5
5 - Seat heaters, Climatronic, Navi- gation system, recirculated air
flap, multifunction steering
wheel, exterior mirror heaters ..... 7.5
6 - Central locking control unit ............. 5
7 - Reversing lights, parking aid ........ 10
8 - Mobile phone .................................. 5
9 - ABS/ESP ......................................... 5
10 - Petrol engine: control unit ............ 20
Diesel engine: control unit .............. 5No. Electrical component A
11 - Dash panel insert, selector lever
lock solenoid (automatic
gearbox) .......................................... 5
12 - Power supply for diagnosis, mobile phone ............................... 7.5
13 - Brake lights ................................... 10
14 - Interior light, central locking ......... 10
Interior light (without central
locking) ......................................... 10
15 - Instrument cluster, automatic gearbox, steering lock angle
sensor, rear-view mirrors ................ 5
16 - Air conditioning, electric water pump ............................................. 10
17 - Police .............................................. 5
18 - Right main beam .......................... 10
19 - Left main beam ............................. 10
20 - Right low beam, headlight range control ................................. 15
21 - Left low beam ............................... 15
22 - Right parking light ........................... 5
23 - Left parking light ............................. 5
24 - Wiper system, washer pump ........ 20
25 - Heater fan ..................................... 25
26 - Rear window heater ...................... 25
27 - Rear window wiper ....................... 15
28 - Fuel pump ..................................... 15
29 - Petrol engine - engine electronics, ignition ....................... 15
Diesel engine - engine
electronics .................................... 10 No. Electrical component A
30 - Power sliding/tilting roof
............... 20
31 - Automatic gearbox ........................ 20
Haldex coupling .............................. 5
32 - Petrol engine - injectors ............... 10
Diesel engine - injection pump,
control unit .................................... 30
33 - Headlight cleaning system ........... 20
34 - Petrol engine - engine electronics .................................... 10
Diesel engine - engine
electronics .................................... 10
35 - Trailer socket, socket in luggage compartment ............... 30
36 - Fog lights ...................................... 15
37 - S contact
1)................................... 10
38 - Luggage compartment light, central locking, remote fuel
filler flap release ........................... 15
39 - Hazard warning signals ................ 15
40 - Horn .............................................. 20
41 - Cigarette lighter ............................ 15
42 - Radio ............................................. 15
43 - Petrol engine: engine electronics .................................... 10
Diesel engine: engine
electronics .................................... 10
44 - Seat heaters ................................. 15
1)For electrical components which can be oper-
ated after switching off the ignition provided the
ignition key is not withdrawn, e.g. radio.
Page 172 of 189
171
DO-IT-YOURSELF
Main headlight with cap of low beam,
main beam and side lightBefore replacing the bulb (main beam and
low beam, or main beam and low beam, or
side light) you have to remove the protec-
tive cover from the rear part of the head-
light - refer to the text which follows.
Open bonnet.
Press locking plate off the cap and tilt it
out in direction of arrow.
Remove cap of headlamp by pushing it
out toward the middle of the vehicle.
Installation is carried out in the reverse or-
der.
Open bonnet.
Take off cap for headlight.
Hold wire spring clamp B and unplug
connector A.
Detach wire spring clamp B by pressing
toward bulb and fold down in direction of
arrow.
Take out bulb 1 and insert new bulb so
that the locating lugs at the bulb disc en-
gage in the recess of the reflector.
Fold wire clamp over the base of bulb
and push forward until the clamp engages.
Plug in connector.
Fit on cap for the headlight.
Have the headlight beam setting checked
at a Škoda Dealer.
Page 173 of 189
172DO-IT-YOURSELF
Front turn signal lightsOpen bonnet.
Remove securing screw 1.
Push turn signal light housing in direc-
tion of arrow.
Turn bulb holder slightly to the left and
take off.
Press faulty bulb into the socket, turn to
the left and remove.
Insert new bulb and turn fully to the right.
Insert bulb holder and turn slightly to the
right as far as the stop.
Fit turn signal light on outside with the
two retaining lugs at the side into the re-
cesses of the headlight.
Tighten screw 1.
Front side light bulb Open bonnet.
Take off cap for headlight.
Pull out light socket with bulb - see ar-
row.
Remove the faulty bulb from the socket.
Insert new bulb.
Fit socket with new bulb into its fixture.
Fit on cap for the headlight.
Fog lights*Open bonnet.
Turn plastic cap for headlight toward
middle of vehicle and then take off.
Separate plug connection B.
Release spring wire clamp A of bulb fix-
ture and fold down.
Take out halogen bulb with cable. Insert
new bulb so that the locating lugs in the
reflector are positioned in the matching re-
cesses in the bulb disc.
Fold spring wire clamp over bulb disc.
Press wire clamp together and lock it again
in place.
Plug in connector.
Fit on cap.
Have the beam setting of the fog lights
checked by a Škoda Dealer.
Page 175 of 189
174DO-IT-YOURSELF
Rear lights (Estate)Open tailgate.
Open side storage compartment
Press spring catches at bulb holder in
direction of arrow and take out bulb holder.
Press faulty bulb into the base, turn to
the left and remove.
Insert new bulb and turn fully to the right.
Insert bulb holder so that the spring cat-
ches engage.
Separate plug connection A.
Press off spring lock of lens on one side
and then on the other side - see arrows. Ca-
refully take off lens in direction of arrow B.
Replace bulb.
Fit lens into housing again until it locks
in place.
Plug in connector.
Carefully press light into door trim panel.
Rear lightsOpen tailgate.
Push cover to the side.
Press spring catches at bulb holder in
direction of arrow and take out bulb holder.
Press faulty bulb into the base, turn to
the left and remove.
Insert new bulb and turn fully to the right.
Insert bulb holder so that the spring
catches engage.
Push back cover.
Page 177 of 189
176DO-IT-YOURSELFAdditional brake lightPress both plastic spring catches of the
housing of the light in the direction of ar-
rows 1.
Take off bulb holder with bulbs in the
direction of arrow 2.
Take faulty bulb out of the holder.
Insert new bulb.
Insert bulb holder into the housing. The
spring catches should lock in place.
Additional brake light (Estate)
We recommend having the bulbs replaced
by a Škoda Dealer.
Interior light and reading light Pull lens down and off the housing (at
the arrow shown in the illustration).
Replace the bulb for the interior light.
Pull bulb for the reading light out of its
socket and insert new bulb.
Press the lens of the light into the hous-
ing again until it locks in place (ensure it is
correctly fitted on).