2004 SKODA OCTAVIA TOUR wheel

162DO-IT-YOURSELF
Tyre repair spray*
The tyre repair spray is precisely for fast
repairs on small tyre defects up to 5 mm.
The spray does not replace a permanent
tyre repair, the repair serves only as an in-
termediate solution until the next service.

The repair can be directly performed on
the vehicle. Carefully read the enclosed in-
structions for direction of use.
On front-wheel drive vehicles, the spray is
located in the well at the front right of the
polypropylene part behind the spare wheel,
and on 4x4 vehicles, in the boot on the left.
Certain models are equipped with a tyre
repair set which includes a compressor and
a repair flask, instructions and accessories.
On front-wheel drive vehicles this set is lo-
cated in the well at the front right of the
polypropylene part behind the spare wheel,
and on 4x4 vehicles, in the boot on the left
next to the first-aid box.

Apply the handbrake before jack-
ing up the car. Never start the engine
when the car is jacked up - risk of
accident.

If it is necessary to carry out work
underneath the vehicle, ensure that
it is supported on suitable stands.
Spare wheelThe spare wheel is stowed in the well below the
floor covering of the luggage compartment and
is secured by a handwheel.

To ensure that the spare wheel is always
ready for use, check the inflation pressure at
regular intervals.
Vehicles with tyres 205/60 R15 and wheel trims
6.5Jx15 have an emergency wheel as a spare
wheel, which has different dimensions and which
is provided with a warning sticker.
Please pay attention to the following instructions,
if you are going to use an emergency wheel:

After fitting on the wheel, the warning sticker
must not be concealed (e.g. by the wheel trim).

Do not drive with this spare wheel at more
than 80 km/h - risk of accident.
Avoid acceleration at full throttle, sharp braking
and fast cornering.

The inflation pressure for this spare wheel is
identical to the inflation pressure of the standard
tyres.

Use this spare wheel only to reach the near-
est service station, as it is not intended for con-
tinuous use.
Tyre repair set*

163
DO-IT-YOURSELF
Changing a wheelWarning

In the case of a flat tyre or punc-
ture, park the vehicle off the road,
switch on the hazard warning lights
and place the warning triangle in po-
sition - note any statutory require-
ments.

All the vehicle occupants should
leave the car and move to a safe area
(e.g. behind safety barrier).


Apply handbrake firmly and engage
a gear. Chock the opposite wheel with
a stone or similar if the car is stand-
ing on a slope.

Never start the engine when the
car is jacked up - risk of accident!

If towing a trailer, unhitch the
trailer from the car before changing
the wheel.

Carry out wheel change on a flat, level
surface, as far as possible.

Remove the car tool kit and spare wheel
from the luggage compartment.

Attach the wire hook (from the car tool
kit) at the edge of the full wheel trim* oppo-
site the air valve. Push the wheel wrench
through the wire hook and pull off the wheel
trim - see illustration.

If light-alloy wheels are fitted, use the
plastic clip supplied to pull off the covers
for the wheel bolts.

Unscrew the safety wheel bolts* - see
page 166.

Fit wheel wrench onto the wheel bolt as
far as the stop and turn to the left. Hold the
wrench as close as possible to its end for
this operation. If the bolts cannot be slack-
ened, you can carefully apply pressure to
the end of the wheel wrench with your foot.
Ensure that you are standing properly and
hold tight on the car. Slacken the wheel
bolts about one turn.

165
DO-IT-YOURSELF

Jack up car until the wheel is just clear
of the ground.

Remove wheel bolts (after slackening)
1),
place them down on a clean surface (cloth,
paper, wheel cap) next to the car jack and
take off wheel.

Fit on spare wheel and attach wheel
bolts
1).

Tighten all the wheel bolts slightly. The
wheel bolts should be clean and turn freely.

On no account grease or oil them!

Lower car and tighten the wheel bolts
diagonally.

Press on the full wheel trim* first at the
valve opening and then apply pressure
around the entire circumference so that the
trim locks in position.
1)In order to accelerate the screwing out and in,
use the handle part of the screwdriver from the
car tool kit, which has on its end a hexagon
socket for the screw head.

Place the wheel removed in the spare
wheel well and secure with the handwheel.
Notes

After changing a wheel, pay attention to
the following points:
- Check the inflation pressure of the spare wheel fitted.
- Have the tightening torque of the wheel bolts checked with a torque wrench as
soon as possible. The tightening torque
for steel and light alloy wheels is 120 Nm.

Have the faulty wheel repaired as quickly
as possible. Warning
In case of incorrect treatment of the
wheel bolts, the wheel can loosen
when the car is moving - risk of acci-
dent!
Wheel bolts must be clean and must
turn easily. However
, they must never
be treated with grease or oil.
If the wheel bolts are tightened to a
too low tightening torque, the trims
can loosen when the car is moving -
risk of accident! A tightening torque,
which is too high, can damage the
bolts and threads and this can result
in permanent deformation of the con-
tact surfaces on the trims.
If it is intended to subsequently fit
wheels or tyres other than the factory-
fitted versions to the car, it is essen-
tial to read the remarks on page 156.

166DO-IT-YOURSELF

Pull off the wheel caps and fit adapter B
onto the wheel bolt A. Turn adapter until
the splines engage.

Slacken or tighten the wheel bolt by fit-
ting the wheel wrench to the hexagon of the
adapter.

After removing the adapter, fit a protec-
tive cap onto the wheel bolt.
Note

It is essential that the locking bolt is tight-
ened to a torque of 120 Nm . If this torque
is exceeded, the bolt and the adapter may
in certain circumstances be damaged.

On steel wheels, the theft-deterrent
wheel bolt must always be installed in the
hole, which is close to the valve. Otherwise
the full wheel trim cannot be mounted and
the full wheel trim can be damaged during
the assembly.

You can also obtain the wheel lock bolt
set as a Genuine Accessory from your
Škoda dealer.
Anti-theft lock of wheels*Wheel locking bolts
A - Wheel bolt
B - Adapter
If wheel locking bolts are fitted to a car (one
bolt for each wheel), these can only be
slackened and tightened using the adapter
supplied. It is good practice to note the code
No. indicated on the adapter.
If the adapter or the wheel locking bolt is
lost, contact your Škoda Dealer.
Fire extinguisher*The fire extinguisher is located in the holder
below the driver seat and is secured with
straps.

Carefully read the instructions regarding
the fire extinguisher.

The fire extinguisher must be inspected
once a year by a regular person or a com-
pany. Please pay attention to the different
legal regulations.

The fire extinguisher is only delivered in
certain countries.

Pay attention to the expiration date of the
fire extinguisher. If the fire extinguisher is
used after the expiration date, its proper
function is no longer assured.

168DO-IT-YOURSELFFuse assignment
No. Electrical component A
1 - Mirror and spray nozzle heater,relay for cigarette lighter
el. seats ........................................ 10
2 - Turn signal lights .......................... 10
3 - Stowage compartment light ............ 5
4 - Licence plate lights ......................... 5
5 - Seat heaters, Climatronic, Navi- gation system, recirculated air
flap, multifunction steering
wheel, exterior mirror heaters ..... 7.5
6 - Central locking control unit ............. 5
7 - Reversing lights, parking aid ........ 10
8 - Mobile phone .................................. 5
9 - ABS/ESP ......................................... 5
10 - Petrol engine: control unit ............ 20
Diesel engine: control unit .............. 5No. Electrical component A
11 - Dash panel insert, selector lever
lock solenoid (automatic
gearbox) .......................................... 5
12 - Power supply for diagnosis, mobile phone ............................... 7.5
13 - Brake lights ................................... 10
14 - Interior light, central locking ......... 10
Interior light (without central
locking) ......................................... 10
15 - Instrument cluster, automatic gearbox, steering lock angle
sensor, rear-view mirrors ................ 5
16 - Air conditioning, electric water pump ............................................. 10
17 - Police .............................................. 5
18 - Right main beam .......................... 10
19 - Left main beam ............................. 10
20 - Right low beam, headlight range control ................................. 15
21 - Left low beam ............................... 15
22 - Right parking light ........................... 5
23 - Left parking light ............................. 5
24 - Wiper system, washer pump ........ 20
25 - Heater fan ..................................... 25
26 - Rear window heater ...................... 25
27 - Rear window wiper ....................... 15
28 - Fuel pump ..................................... 15
29 - Petrol engine - engine electronics, ignition ....................... 15
Diesel engine - engine
electronics .................................... 10 No. Electrical component A
30 - Power sliding/tilting roof
............... 20
31 - Automatic gearbox ........................ 20
Haldex coupling .............................. 5
32 - Petrol engine - injectors ............... 10
Diesel engine - injection pump,
control unit .................................... 30
33 - Headlight cleaning system ........... 20
34 - Petrol engine - engine electronics .................................... 10
Diesel engine - engine
electronics .................................... 10
35 - Trailer socket, socket in luggage compartment ............... 30
36 - Fog lights ...................................... 15
37 - S contact
1)................................... 10
38 - Luggage compartment light, central locking, remote fuel
filler flap release ........................... 15
39 - Hazard warning signals ................ 15
40 - Horn .............................................. 20
41 - Cigarette lighter ............................ 15
42 - Radio ............................................. 15
43 - Petrol engine: engine electronics .................................... 10
Diesel engine: engine
electronics .................................... 10
44 - Seat heaters ................................. 15
1)For electrical components which can be oper-
ated after switching off the ignition provided the
ignition key is not withdrawn, e.g. radio.

179
DO-IT-YOURSELF
It is not recommended to tow-start the
vehicle (despite observing the instruc-
tions which are given in the Owner’s
Manual) in view of the fact that severe
engine damage may result in certain cir-
cumstances.
It is best to attempt to start the engine
by using jump-starting cables - refer to
page 177 of the Owner’s Manual - or to
call on the services of SERVICE Mobil.
General information

The tow rope should be elastic so that
there is no strain on either vehicle. It is best
to use only plastic fibre ropes or ropes
made of a similarly elastic material. It is
important to ensure that no impermissible
pulling forces and no sudden shock loads
occur. If attempting to tow a car which is
not on a paved road, there is always a risk
of the parts of the car to which the tow rope
is attached being subjected to excessive
stress and damaged.

Before attempting to start the engine
by tow-starting the car, always use the
battery of another vehicle as a jump-
starting aid if possible - see page 177. It is essential to pay attention to the follo-
wing points when tow-starting and to-
wing the car:


Observe any legal regulations regarding
towing another vehicle.

Both drivers should be acquainted with
the special features of towing a vehicle.
Persons not familiar with towing a vehicle
should not attempt to tow-start or tow a car.

If a tow rope is used, the driver of the
towing vehicle should engage the clutch
particularly softly when moving off and shift-
ing gears.

The driver of the towed car should en-
sure that the tow rope is always taught.

The ignition of the towed car should be
switched on so that the steering wheel is
not blocked and the turn signal lights, the
windscreen wipers, horn, lights and other
electrical components can be switched on.

As the brake servo unit only operates
when the engine is running, note that suffi-
ciently greater force is required to depress
the brake pedal when the engine is not run-
ning and the steering is also much more
difficult to operate.
For technical reasons, it is not possible
to tow-start a car fitted with an automatic
gearbox.
In the event of a defect in the gearbox,
your vehicle no longer contains lubri-
cant, the car must be towed with the
driving wheels lifted or on a special
transporter or trailer.

180DO-IT-YOURSELFAdditional points for the driver of the to-
wed vehicle to note during tow-starting:

Before starting to tow the car, engage
3rd or 4th gear, depress clutch pedal and
hold. The ignition should be switched on.

Once both vehicles are moving, release
the clutch pedal.

As soon as the engine has started, de-
press clutch pedal and take the car out of
gear to avoid running into the towing vehi-
cle.

If your car is fitted with a catalytic con-
verter, the engine must not be started by
towing the car over a distance of more
than 50 m (150 ft) if the catalytic con-
verter is warm otherwise uncombusted
fuel may get into the catalytic converter
and cause damage. Pay attention to the following points if
towing a car fitted with an automatic
gearbox:


Move the shift lever into position „N“.

The maximum towing speed is 50 km/h
(30 mph).

The maximum towing distance is 50 km
(30 miles)!

If the car has to be towed over a greater
distance, the front wheels should be raised
clear of the ground.
The gear oil pump does not operate when
the engine is not running; consequently, the
gearbox is not sufficiently lubricated when
running at high speeds and over lengthy
distances.

If the car is towed by a tow truck, the front
wheels should always be raised clear of the
ground.
If the rear wheels are raised clear of the
ground, the drive shafts will rotate in the
opposite direction. As a result, the gears in
the automatic gearbox will run at such high
speeds that the gearbox could suffer se-
vere damage within a short time.

182ALPHABETICAL INDEX4x4 models, 123AABS, 60, 122
Accessories, 159- Changes and replacement ofparts, 159
Accumulator, 146
Acoustic signals, 46
Adjustable steering wheel, 43
Adjusting, - Seats, 19
- Seat belt height, 100
- Headlamp beam, 66
Air conditioning system, 75
Air outlet vents, 73, 76, 83
Airbag system, 56, 103
Airbag, 103
Alarm, 13
Anti-theft alarm system, 13
Armrest, 36
Ashtrays, 90
Automatic air conditioning, 79
Automatic gearbox, 39
Automatic vehicle wash systems, 130
Automatic wipe/wash, 71BBalancing wheels, 154
Battery - charging, 61 Battery - recharging, 149
Battery, 146
Beverage holder, 87
Beverages, 87
Bonnet, 135
- Opening, 135
- Closing, 135
Brake Assist, 121
Brake booster, 121
Brake fluid level, 144
Brake fluid, 61, 144
Brake fluid, 61, 144
Brake pad, 58
Brake system, 61, 120, 121, 122, 123, 144
Brakes, 61, 120, 121, 122, 123, 144
Breakdown assistance, 161
Bulbs, 60, 161, 170
CCavity protection, 134
CD changer, 31
Central locking, 8 - Opening a single door, 9
Cigarette lighter, 89
Climatronic, 79
Clock, 50
Cockpit, 5
Coming home, 67
Convenience operation, 10, 16, 86
Coolant level, 143 Coolant temperature, 48
Coolant, 48, 58, 142
Coolant, 48, 58, 142
Cooling, 142
Cruise control system, 68
DDefrosting windows, 63, 73, 76
Diesel engines, 46
Diesel, 128
Digital clock, 50
Disc wheels, 133
- Steel wheels, 133
- Light-alloy wheels, 133
Door and window seals, 132
Door, 8
Driving abroad, 158
Driving economically and in an environmentally
Dust, noise and pollen filter, 152EEDL, 61, 122
Electric sliding/tilting roof, 85
Electrical power windows, 15
Electrically adjustable seats , 20
Engine - starting, 44
Engine - switching off, 46
Engine compartment, 135
Engine electronics, 57, 60