2004 PORSCHE CAYENNE light

130
Multi-Purpose Display and Instruments
Presetting speedYou can define a speed limit in the menu
MPH-LIMIT.
Activating or deactivating the limit
Example: Front side light warning messageDisplaying warning messagesAll current warnings and information relating to the
traffic safety of the vehicle can be displayed in the
menu WARNINGS.
Danger!
Warning messages indicate possible faults.
fGo to an authorized Porsche dealer immediately.
1.MAIN MENU
>MPH-LIMIT
Select and confirm.
2.Select MPH SET.
3.Set desired limit:
- Press briefly: Limit is set in increments of
1 mph (around 1.6 km/h).
- Press for longer than 2 seconds: Limit is set
in increments of 10 mph (16 km/h).
4.Confirm selection.
LIMIT ACTIVE is activated automatically.
1.MAIN MENU
>MPH-LIMIT
Select and confirm.
2.Select LIMIT ACTIVE.
3.Confirm selection.
LIMIT ACTIVE is activated
LIMIT ACTIVE is deactivated
4.Select BACK.
5.Confirm selection.
Sub-menu MPH-LIMIT is displayed.
10_Cayenne_21_KW17.book Seite 130 Donnerstag, 9. April 2009 3:33 15

Multi-Purpose Display and Instruments
133
fIf a tire pressure message is displayed, correct
the tire pressure at the next opportunity.
fIncomplete entries or selection of the wrong
tires on the multi-purpose display affect
correct indication of warnings and messages.
The settings in the TYRE PRESSURE menu
must be updated after wheel changes, use of
a spare wheel or changes in vehicle loading.
fUse only the pressure differences shown in the
TYRE PRESSURE menu or from tire pressure
messages or warnings when correcting the
tire pressure.
fTires lose air over time without a tire defect
being present. A tire pressure warning will then
appear on the multi-purpose display.
Correct tire pressure.
Functional description of Tire Pressure
MonitoringTire Pressure Monitoring continuously monitors
tire pressure and tire temperature on all four
wheels and warns the driver when the tire
pressure is too low.The display as well as the settings for Tire
Pressure Monitoring take place on the multi-
purpose display in the sub-menu
TYRE PRESSURE.
However, the tire pressure must still be set
manually on the wheel.
The deviations in the tire pressures from the
required pressures are shown in the sub-menu
TYRE PRESSURE.
Example:
If the tire pressure display shows “–4 psi
(–0.3 bar)”, you must increase the tire pressure by
4 psi (0.3 bar).
The tire pressures to be monitored are fixed in the
Tire Pressure Monitoring system and cannot be
changed.
The following settings must be made to permit
correct monitoring.
–Tires
Select the type and size of the tires fitted on
the vehicle.
–Load
Select the type of loading.
Note on operation
Settings can be made only when the vehicle is
stationary.
fFor information on tires and wheels:
Please see the chapter “TIRES/WHEELS” on
Page 281.
Warning!
Your vehicle has also been equipped with a TPM
malfunction indicator to indicate when the system
is not operating properly.
The TPM malfunction indicator is combined with
the low tire pressure telltale.
When the system detects a malfunction, the
telltale will flash for approximately one minute and
then remain continuously illuminated. This
sequence will continue upon subsequent vehicle
start-ups as long as the malfunction exists.
When the malfunction indicator is illuminated, the
system may not be able to detect or signal low tire
pressure as intended.
TPM malfunctions may occur for a variety of
reasons, including the installation of replacement
or alternate tires or wheels on the vehicle that
prevent the TPM from functioning properly.
Always check the TPM malfunction telltale after
replacing one or more tires or wheels on your
vehicle to ensure that the replacement or alternate
tires and wheels allow the TPM to continue to
function properly.Warning light
10_Cayenne_21_KW17.book Seite 133 Donnerstag, 9. April 2009 3:33 15

134
Multi-Purpose Display and Instruments
Setting the tire type and size
Warning!
Incomplete entries or selection of the wrong
tires on the multi-purpose display affect
correct indication of warnings and
messages.
fThe settings must be updated in the TYRE
PRESSURE menu after changing a wheel, filling
with tire sealant or adding air (after previous
warning “Flat tyre”).
fPlease see the chapter ““FLAT TYRE” WARNING” on Page 136.
The settings of the multi-purpose display must be
updated after changing wheels or tires on the
vehicle.
The tire type and tire size must be selected even
if the settings for the new set of wheels are the
same as for the old wheels.Note on operation
fFor information on the operating principle of
the multi-purpose display:
Please see the chapter “OPERATING
PRINCIPLE” on Page 124.After driving off, the system starts to teach the
wheels and wheel positions on the vehicle. During
this time, the tire pressure warning light on the
speedometer flashes about 60 seconds and lights
up thereafter permanently, and no current tire
pressure information is available on the displays.
Note
Information on the tire size and type can be found
on the tire sidewall. For further information on the
details on the tire sidewall:
fPlease see the chapter “INSCRIPTION ON
RADIAL TIRE” on Page 290.
Note on operation
Before fitting tires approved by Porsche with a
size which is not already stored in the multi-
purpose display, the missing information should
be supplemented in the multi-purpose display.
fGo to an authorized Porsche dealer
immediately.
1.MAIN MENU
>TYRE PRESS.
>SETTINGS
Select and confirm.
2.Select TYRES.
3.Confirm selection.
The TYRE TYPE list is displayed.
4.Select tire type (e.g. SUMMER).
The list with the possible tire sizes (e.g. for the
selection SUMMER) is displayed.
5.Select tire size (e.g. 18 inch).
6.Confirm selection.
The current settings are displayed.
10_Cayenne_21_KW17.book Seite 134 Donnerstag, 9. April 2009 3:33 15

136
Multi-Purpose Display and Instruments
“Flat tyre” warningThe warning threshold for output of this warning
message is speed-dependent.
At a speed of below 100 mph (160 km/h), this
warning indicates a pressure loss of at least 7 psi
(0.5 bar); at a speed of above 100 mph
(160 km/h), the warning indicates a pressure loss
of at least 6 psi (0.4 bar). The message indicates
the wheel in which the pressure loss has been
detected. The deviation from the required
pressure is displayed for the corresponding
wheel. The tire pressure warning light on the
speedometer lights up in addition to the warning
message. This significant pressure loss is a
danger to road safety.
fThe warning message can be acknowledged
while driving.
To do this, press the ENTER button on the
wiper stalk. The tire pressure warning light on
the speedometer remains lit.
The measure display SELECTION AFTER
WARNING appears only after the ignition is
switched back on again.
The display shows: SELECTION AFTER WARNING1. Stop the vehicle immediately in a suitable
place.
2. Check the indicated wheel for damage.
3. Fill the tire or change the wheel, as appro-
priate.
- Adding air
Example: If the tire pressure display shows
“–7 psi (---0.5 bar)”, you must increase the tire
pressure by 7 psi (0.5 bar).
On vehicles without air suspension:
Please see the chapter “CHECKING TIRE
PRESSURE WITH A PRESSURE GAGE” on
Page 306.
On vehicles with air suspension:
Please see the chapter “INFLATING TIRES ON
VEHICLES WITH AIR SUSPENSION” on
Page 308.
or- Changing wheel with spare wheel or
collapsible spare wheel
For information on jacking up the vehicle:
Please see the chapter “LIFTING THE VEHICLE
WITH A LIFTING PLATFORM OR GARAGE LIFT”
on Page 298.
For information on changing a wheel:
Please see the chapter “LIFTING THE VEHICLE
WITH A JACK” on Page 299.
or
- Sealing with tire sealant.
For information on handling and filling the
sealant: Please see the chapter “USING TIRE
SEALANT” on Page 296.
4. Switch ignition on again.
The “Flat tyre” warning first appears again on
the multi-purpose display. The display changes
to SELECTION AFTER WARNING after a few
seconds.
5. Select the action which has been carried out
on the vehicle on the display with the rocker
switch.
- ADD AIR or
- WHEEL CHANGE > SPARE WHEEL > Spare
wheel type or
- SEALING SET
6. Press the ENTER button.
10_Cayenne_21_KW17.book Seite 136 Donnerstag, 9. April 2009 3:33 15

138
Multi-Purpose Display and Instruments The spare wheel and collapsible spare wheel are
not equipped with wheel transmitters and are not
monitored by Tire Pressure Monitoring.
Wheel change (without warning)The settings of the multi-purpose display must be
updated after changing wheels or tires on the
vehicle.
Please see the chapter “SETTING THE TIRE TYPE
AND SIZE” on Page 134.Setting spare wheel/sealant (without
warning)If you have fitted a spare wheel or collapsible
spare wheel or used tire sealant without being
requested to do so by a “Flat tyre” warning on the
multi-purpose display, you must subsequently
update the settings in the TYRE PRESSURE sub-
menu.Setting spare wheel.
The spare wheel is not equipped with a wheel
transmitter and is not monitored by Tire Pressure
Monitoring. The tire pressure warning light on the
speedometer flashes about 60 seconds and lights
up thereafter permanently when the ENTER button
is pressed. The value “_” is displayed in the sub-
menu TYRE PRESSURE (filling information) at the
position of the spare wheel.
The reminder SPARE WHEEL/SEALING SET
OPERATION? appears each time the ignition is
switched on. For information on spare wheel/
sealing set operation: Please see the chapter
“NOTE ON SPARE WHEEL/SEALING SET OPERA-
TION” on Page 140.
1.MAIN MENU
>TYRE PRESS.
>SETTINGS
> TYRES
> SPARE WHEEL
Select and confirm.
2.Select SPARE WHEEL.
3.Confirm selection.
The display automatically returns to the TYRE
PRESSURE sub-menu (filling information).
The required tire pressures are displayed
here.
Select BACK.
4.Confirm selection.
The basic display appears.
10_Cayenne_21_KW17.book Seite 138 Donnerstag, 9. April 2009 3:33 15

Multi-Purpose Display and Instruments
139
Warning!
Risk of accident, resulting in serious
personal injury or death. The spare wheel is
not equipped with a wheel transmitter and is
not monitored by Tire Pressure Monitoring.
fThe spare wheel must be used only over short
distances.
For information on handling and fitting/
removing the spare wheel: Please see the chapter “SPARE WHEEL” on Page 309.Setting collapsible spare wheel.
The collapsible spare wheel is not equipped with a
wheel transmitter and is not monitored by Tire
Pressure Monitoring. The tire pressure warning
light on the speedometer flashes about
60 seconds and lights up thereafter permanently
when the ENTER button is pressed. The value “_”
is displayed in the sub-menu TYRE PRESSURE
(filling information) at the position of the
collapsible spare wheel.
A warning appears on the multi-purpose display if
the speed limit of 50 mph (80 km/h) is exceeded.
The reminder SPARE WHEEL/SEALING SET
OPERATION? appears each time the ignition is
switched on.
For information on spare wheel/sealing set opera-
tion: Please see the chapter “NOTE ON SPARE
WHEEL/SEALING SET OPERATION” on Page 140.
Warning!
Risk of accident, resulting in serious
personal injury or death. The collapsible
spare wheel is not equipped with a wheel
transmitter and is not monitored by Tire
Pressure Monitoring.
fThe collapsible spare wheel must be used only
over short distances.
For information on handling the collapsible
spare wheel: Please see the chapter “COLLAPSIBLE SPARE WHEEL” on Page 305. Warning!
Risk of accident, resulting in serious
personal injury or death if a collapsible spare
wheel is in use.
fAvoid hard acceleration and high cornering
speeds.
fDo not exceed maximum speed of 50 mph
(80 km/h).
fPlease observe the safety and operating
instructions on the tire compressor.
fHave the collapsible spare wheel replaced by
an authorized Porsche dealer as soon as possible.
1.MAIN MENU
>TYRE PRESS.
>SETTINGS
> TYRES
> SPARE WHEEL
Select and confirm.
2.Select COLLAP. WHEEL.
3.Confirm selection.
The required pressure and speed limit for the
collapsible spare wheel are displayed.
10_Cayenne_21_KW17.book Seite 139 Donnerstag, 9. April 2009 3:33 15

Multi-Purpose Display and Instruments
141
fSet the fitted wheel set with tire type and tire
size.
Please see the chapter “SETTING THE TIRE
TYPE AND SIZE” on Page 134.
Note on operation
The reminder SPARE WHEEL/SEALING SET
OPERATION? goes out automatically after approx.
10 seconds if no selection is made during this
time. The original selection “YES” is then
maintained.In the event of faults, Tire Pressure Monitoring
cannot monitor the tire pressure. A distinction is
made between partial monitoring and inactive
system.
In the case of partial monitoring, the tire pressure
warning light on the speedometer flashes about
60 seconds and lights up thereafter permanently.
No message is output on the multi-purpose
display.
If Tire Pressure Monitoring is not active, the tire
pressure warning light on the speedometer
flashes about 60 seconds and lights up thereafter
permanently. A corresponding message is output
on the multi-purpose display.
The warning light goes out as soon as all faults
have been remedied.
Tire Pressure Monitoring switches to partial
monitoring if:
– there are up to two wheel transmitters not
present or faulty (e.g. a spare wheel or collap-
sible spare wheel is fitted that does not have a
wheel transmitter).
In the event of partial monitoring, the value “_” is
displayed in the sub-menu TYRE PRESSURE (filling
information) at the position of the faulty or missing
wheel transmitter.
Tire Pressure Monitoring is not active in the
following cases:
– Tire Pressure Monitoring is faulty,– at least three wheel transmitters for Tire
Pressure Monitoring are faulty or not present,
– temporarily after changing a wheel,
– too many wheel transmitters have been
detected,
– there is external interference by other radio
sources, e.g. wireless headphones,
– tire temperatures are too high.
fFor information on messages on the multi-
purpose display:
Please see the chapter “OVERVIEW OF
WARNING MESSAGES” on Page 149.
Notes on tire pressurePressure increase as the result of tempera-
ture increase
In accordance with physical principles, the tire
pressure changes as the temperature changes.
The tire pressure increases or decreases by
around 1.5 psi (0.1 bar) for every 18 °F (10 °C)
change in temperature.
Tire pressure specifications
The tire pressure must match the prescribed value
(required pressure).
You can find information on the tire pressure for
cold tires 68 °F (20 °C):
Faults in Tire Pressure Monitoring
10_Cayenne_21_KW17.book Seite 141 Donnerstag, 9. April 2009 3:33 15

Multi-Purpose Display and Instruments
145
Option 3:
AUTO LOCK on and AUTO UNLOCK on
Doors lock automatically when a speed of approx.
4 mph (6 km/h) is exceeded.
On vehicles without Porsche Entry & Drive, the
doors are unlocked automatically when the
ignition key is withdrawn.
On vehicles equipped with Porsche Entry & Drive,
the doors are unlocked when the ignition is
switched off twice.
Option 4:
AUTO LOCK off and AUTO UNLOCK on
The doors do not lock automatically.
If the doors are locked with the central locking
system button:
On vehicles without Porsche Entry & Drive, the
doors are unlocked automatically when the
ignition key is withdrawn.
On vehicles equipped with Porsche Entry & Drive,
the doors are unlocked when the ignition is
switched off twice.
Switching daytime driving lights
on/offNote on operation
The options in the LIGHTS menu can only be set
when the vehicle is stationary.USA only:You can activate/deactivate the daytime driving
lights on the multi-purpose display in the instru-
ment panel.
Canada only:The DAYTIME DRIVING LIGHTS function cannot be
deactivated.1.MAIN MENU
> SETTINGS
> LIGHTS
Select and confirm.
2.Select DAYTIME DRIVING LIGHTS.
3.Confirm selection.
Function ist activated.
Function ist deactivated.
10_Cayenne_21_KW17.book Seite 145 Donnerstag, 9. April 2009 3:33 15