2004 PORSCHE 911 GT3 lock

Installing
1. Insert headlight intoguide railsandpush fully
into thewing.
2. Push headlight tothe rear andatthe same
time turnthesocket wrench untilitpoints hor-
izontally tothe rear
C.

The headlight lockingdevicemustperceptibly
and audibly engage.
3. Check headlight forafirm seating, e.g.bypull-
ing itin the area ofthe fog light.
4. Insert rubber plugintotheunlocking opening
and secure thecarpeting.
Check thefunction ofall lights.

I>I>I>

PracticalTips,Emergency Service

Lowbeam, highbeam andadditional
high beam

Opening thelidofthe headlight housing

1. Unscrew thetwo screws
A.

2. Press bothrelease tabsBand remove lid.
Practical Tips,Emergency Service
Changing
bulbforlow beam

1. Turn plugcounter-clockwise (bayonetlock)and
pull itoff.
2. Replace defective bulb.
When doing so,ensure bulbisseated properly.
3. Reassemble inreverse order.
Changing
bulbforlow beam andhigh beam
(Bi-Xenon headlight)

1. Turn plugcounter-clockwise (bayonetlock)and
pull itoff.

2.Turn clamping ringcounter-clockwise (bayonet
lock) andpullitoff.
3. Replace defective bulb.
When doing so,ensure bulbisseated properly.
4. Reassemble inreverse order.

Note

In order toprevent impairment ofthe headlight
beam adjustment function,thecable Cof the plug
must always pointtothe outside ofthe vehicle.
Changing
bulbforhigh beam or
additional highbeam (Bi-Xenon headlight)

1. Turn bulbholder.
Turn itcounter-clockwise onthe leftheadlight
and clockwise onthe right headlight.
Take bulbholder outofthe headlight housing.
2. Pull both plugrelease tabsapart.
Pull plug outofthe bulb holder.
3. Replace thedefective bulbwith bulb holder.
4. Reassemble inreverse order.
Closing
lidofheadlight housing

1. Insert retaining lugsoflid into thebottom of
the headlight housingandclose liduntil itper-
ceptibly engages.
2. Screw inboth screws.

[>[>[>

Practical Tips,Emergency Service
.1.67

Changing bulbforparking light
1. Turn capinthe headlight housingcounter-
clockwise andremove thecap.

168
PracticalTips,Emergency Service 2
. Turn bulbholder.
Turn itcounter-clockwise onthe leftheadlight
and clockwise onthe right headlight.
Take bulbholder outofthe headlight housing.
3. Turn defective bulbcounter-clockwise (bayo-
net lock) andreplace it.
4. Reassemble inreverse order. Changing
bulbforturn
signal light

1. Turn bulbholder inthe headlight housing
counter-clockwise andpullitout.
2. Turn defective bulbcounter-clockwise (bayo-
net lock) andreplace it.
3. Reassemble inreverse order.

Changingbulbforfog light

1. Turn capinthe headlight housingcounter-
clockwise andremove thecap. 2.
Press theretaining clipdown withascrewdriv-
er and push itto the left.
3. Pivot theretaining clipback. 4.
Pull bulb withcable outofthe headlight
housing.
5. Disconnect plugconnection andreplace the
defective bulb.
6. Reassemble inreverse order.
Practical Tips,Emergency Service
169

Changing Bulbinthe Side
Marker Light

1. Remove capinthe wheel housing linerwiththe
screwdriver.
2. Insert screwdriver intotheopening inthe wheel
housing lineratright angles tothe side marker
light housing.
By pressing withthescrewdriver, disengage
the securing springofthe side marker light
housing.

110
PracticalTips,Emergency Service 3.
Remove sidemarker lightandundo bulbholder
(bayonet lock),
4. Remove bulbfrom theholder andreplace.
Insert holder.
5. Insert thelight tabs (arrow A)into thewing at
the front.
Engage securing spring(arrow
B)
inthe wing.
6. Press capintothewheel housing liner.
Check operation ofthe light.

Tail
light
left

Taillight

Changing bulb

1. Open lidofengine compartment.
2. Unscrew fastening screwAand pulltaillight
back (arrow) andout.
A
-Taillight, brakelight

B -
Reversing light
C -Turn signal light

o -Rear
foglight

E -
Side marker light

3. Turn bulbholder counter-clockwise and
remove fromtaillight.
4. Replace defective bulb(bayonet mount).
5. Insert bulbholder andturn clockwise. 6.
Insert taillight inthe fender.
Ensure thatlocating lug(arrow) iscorrectly
positioned.
7. Screw infastening screwA.
8. Check operation ofthe light.
Practical Tips,Emergency Service
171

Interior Light,Reading Lights

Changing bulb

1. Carefully pulllight housing outofthe lining

(arrow).
2.

Reading light:

Turn theholder Aof the defective bulbcounter-
clockwise, andremove.
Remove bulbandreplace.

Interior light:

Carefully unclipthelight lensonthe switch side

(arrow)
andthen detach it.
Remove defective bulbfrom between thecon-
tact springs andreplace.
Clip light lensback in. 3.
Insert lighthousing intothelining rearendfirst.
Press frontofhousing upand click intoplace.
Check operation oflights.
Practical Tips,Emergency Service
173