2004 PORSCHE 911 GT3 service

+
=Positive terminal
for
jump starting
- =Grounding point
for
jump starting

Connect jumpercablesinthe following
sequence:

1. Check electrolyte levelofeach cell.Ifneces-
sary, fillwith distilled watertojust above
plates.
2. Onavehicle withadischarged battery:turnoff
all consumers andaccessories, movethegear
shift lever intotheneutral position andsetthe
parking brake.
3. Open thecap ofthe positive terminal forjump
starting
(+).
4.
Attach the
positive cable
firsttothe positive
terminal forjump starting (+),
then tothe positive terminal ofthe booster bat-
tery.
5. Connect the
negative cable
firsttothe nega-
tive terminal ofthe booster battery,thentothe
grounding pointforjump starting (-).
6. Run theengine ofthe booster caratahigher
speed.
7. Start theengine.
An attempted startusing jumper cablesshould
not last more than15seconds. Thenallowa
waiting periodofatleast oneminute.
8. With theengine running, disconnect bothjump-
er cables inreverse order.
Close thelidofthe jump startbox.
PracticalTips,Emergency Service

Lights, Replacing Bulbs

A
Warning!
Risk ofshort circuit.

c>
Always switchoffthe relevant consumer when
changing bulbs.

Risk ofinjury. Theheadlights areunder high
voltage wheninstalled.

c>
Becareful duringallwork inthe area ofthe
headlights.

Risk ofdamage. Bulbsofahigher wattage
can damage thelamp housing.

c>
Only thebulbs shown inthe chart maybeused.

c>
New bulbs mustbeclean andfree from
grease.
Therefore, nevertouch bulbswith
your barehands.

Use acloth orsoft paper whilereplacing bulbs.

c>
For reasons oftraffic safety, werecommend
that youalways carryspare bulbssothat you
can have acorrectly illuminated caratall
times. In certain countries, thecarrying ofspare
bulbs ismandatory.
Practical Tips,Emergency Service
A

Caution!
Risk ofdamage toheadlights duetoexces-
sive temperatures andabrasion.

c>
Attach nocoverings (e.g.films, "stone
guards") inthe area ofthe headlights.

c>
Use soapy wateronlytoclean lightlenses and
plastic headlight lenses.
In no case maychemical cleanersorother vol-
atile cleaning fluidsbeused.

c>
Toprevent scratches, donot rubwith adry or
merely moistcloth,tissue orinsect sponges.

BulbChart

Type.
rating

Low beam
H7,55W
Bi-Xenon lowbeam
Philips,D2S35W
High beam
H9,65W
Additional highbeam
(with Bi-Xenon headlights)
Hll,55W
Fog lights
H3,55W
Rear foglight,
Reversing light
P21 W
Taillight, brakelight
P21 /5 W
Raised brakelight
W3W
Turn signal light
PY21W
Parking lightfront
H6W
Side marker light
WY5W
Door guardjkerb light
W5W
License platelight
C5W
Luggage compartmenVengine
compartment light,interior light
K10 W
Reading light
6W Xenon
PracticalTips,Emergency Service

Headlights

Removal
1. Unscrew plasticnut
A.

Detach sidecarpeting.
Practical Tips,Emergency Service 2.
Remove rubberplugBfrom theunlocking
opening. 3.
Place socket wrench fromtoolkitonthe
unlocking spindle.
The handle ofthe wrench shouldpoint
horizontally tothe rear.
4. Turn socket wrench approx. 180
0
Aand leave
in position.
The headlight isnow unlocked andcanbe
pulled forward outofthe wing.
5. Turn socket wrench backuntilitis pointing ver-
tically downward
B.

Installing
1. Insert headlight intoguide railsandpush fully
into thewing.
2. Push headlight tothe rear andatthe same
time turnthesocket wrench untilitpoints hor-
izontally tothe rear
C.

The headlight lockingdevicemustperceptibly
and audibly engage.
3. Check headlight forafirm seating, e.g.bypull-
ing itin the area ofthe fog light.
4. Insert rubber plugintotheunlocking opening
and secure thecarpeting.
Check thefunction ofall lights.

I>I>I>

PracticalTips,Emergency Service

Lowbeam, highbeam andadditional
high beam

Opening thelidofthe headlight housing

1. Unscrew thetwo screws
A.

2. Press bothrelease tabsBand remove lid.
Practical Tips,Emergency Service
Changing
bulbforlow beam

1. Turn plugcounter-clockwise (bayonetlock)and
pull itoff.
2. Replace defective bulb.
When doing so,ensure bulbisseated properly.
3. Reassemble inreverse order.
Changing
bulbforlow beam andhigh beam
(Bi-Xenon headlight)

1. Turn plugcounter-clockwise (bayonetlock)and
pull itoff.

2.Turn clamping ringcounter-clockwise (bayonet
lock) andpullitoff.
3. Replace defective bulb.
When doing so,ensure bulbisseated properly.
4. Reassemble inreverse order.

Note

In order toprevent impairment ofthe headlight
beam adjustment function,thecable Cof the plug
must always pointtothe outside ofthe vehicle.
Changing
bulbforhigh beam or
additional highbeam (Bi-Xenon headlight)

1. Turn bulbholder.
Turn itcounter-clockwise onthe leftheadlight
and clockwise onthe right headlight.
Take bulbholder outofthe headlight housing.
2. Pull both plugrelease tabsapart.
Pull plug outofthe bulb holder.
3. Replace thedefective bulbwith bulb holder.
4. Reassemble inreverse order.
Closing
lidofheadlight housing

1. Insert retaining lugsoflid into thebottom of
the headlight housingandclose liduntil itper-
ceptibly engages.
2. Screw inboth screws.

[>[>[>

Practical Tips,Emergency Service
.1.67

Changing bulbforparking light
1. Turn capinthe headlight housingcounter-
clockwise andremove thecap.

168
PracticalTips,Emergency Service 2
. Turn bulbholder.
Turn itcounter-clockwise onthe leftheadlight
and clockwise onthe right headlight.
Take bulbholder outofthe headlight housing.
3. Turn defective bulbcounter-clockwise (bayo-
net lock) andreplace it.
4. Reassemble inreverse order. Changing
bulbforturn
signal light

1. Turn bulbholder inthe headlight housing
counter-clockwise andpullitout.
2. Turn defective bulbcounter-clockwise (bayo-
net lock) andreplace it.
3. Reassemble inreverse order.