2004 Peugeot 406 C engine

02-02-2004
YOUR 406 COUPE IN DETAIL
86
Make a careful note of the number on each key. The key number is coded on the label attached to the key. If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a
possibility that it may unlock your vehicle, without you being aware of it.The remote control does not operate when the key is in the ignition, even when the ignition is switched off, except for reprogramming. Do not operate the deadlocking function if there is anyone inside the vehicle.Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult
in an emergency. As a safety precaution (with children on board), remove the ignition key when you leave the vehicle, even for a short time.
Do not repeatedly press the button of your remote control out of range of your vehicle. You run the risk of stopping it from working and the remote control would have to be reprogrammed. When purchasing a second-hand vehicle: - ensure that you are given the confidential card;
- have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.

02-02-2004
YOUR 406 COUPE IN DETAIL85
Changing the battery of the remote control The information
"battery flat"is
given by an audible signal accompa- nied by a message on the multi-func-
tion display.
To replace the battery, unclip the
casing using a coin at the ring(CR 2016/3 volt battery).If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOTdealer on the electronic immobiliser
system. This code is hidden by afilm, which should be removed only if
necessary. Keep your card in a safe place, never inside the vehicle.
Programming the remote con- trol
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately for a
few seconds.
 Switch off the ignition and remove the remote control key from the
ignition lock. The remote controlis now working again.
ELECTRONIC ENGINE IMMOBILISER This locks the engine management system as soon as the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the code is recognised and starting ispossible. If the system does not function correctly
, contact a PEUGEOT
dealer as soon as possible.

02-02-2004
YOUR 406 COUPE IN DETAIL
86
Make a careful note of the number on each key. The key number is coded on the label attached to the key. If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a
possibility that it may unlock your vehicle, without you being aware of it.The remote control does not operate when the key is in the ignition, even when the ignition is switched off, except for reprogramming. Do not operate the deadlocking function if there is anyone inside the vehicle.Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult
in an emergency. As a safety precaution (with children on board), remove the ignition key when you leave the vehicle, even for a short time.
Do not repeatedly press the button of your remote control out of range of your vehicle. You run the risk of stopping it from working and the remote control would have to be reprogrammed. When purchasing a second-hand vehicle: - ensure that you are given the confidential card;
- have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.

02-02-2004
YOUR 406 COUPE IN DETAIL91
BOOT Simultaneous locking or unlocking of the boot and the doors
Turn the key a quarter turn from
Ato
B .
The boot is then controlled by the remote control or the driver's doorlock. Locking the boot only
Turn the key a quarter of a turn from A to C. The boot is then locked,
whatever the action of the remotecontrol or the driver's door lock.
To return to simultaneous operation with the doors: turn the key from Ato
B .OPENING THE BONNET From inside: pull the handle on the
left-hand side under the fascia.From outside: lift the catch and
raise the bonnet. Bonnet struts These open the bonnet and hold it open.
To close Lower the bonnet and release it at the end of its travel. Check that thebonnet is properly locked. FILLING WITH FUEL Fill with fuel with the engine switched
off.
To open the fuel filler flap, firmly pull the handle on the floor on the left ofthe driver's seat. If you are filling up your tank, do not
continue after the 3rd cut-off of thepump; this could cause your vehicleto malfunction. The capacity of the tank is approx- imately 15.4 gallons (70 litres).
A filler cap hook is provided on the inside of the fuel filler flap.

02-02-2004
AUTOMATIC SWITCHING ON OF THE LIGHTS The side lights and dipped beam headlamps switch on automatically if
the light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories position (1st notch),
 Press the end of the lights stalkfor more than two seconds.
Note: in foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located on the windscreen behind
the mirror. It is used for automat-ic switching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multi-function display. Note: Manual operation of the lights
stalk always takes priority Disarming Disarming of the function is accom- panied by an audible signal and themessage "Automatic lighting of
the headlamps deactivated" on the
multi-function display. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is howeverpossible to disarm this function and
switch off the lights by:
Ð manually switching off the lights using the lights stalk,
Ð switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights come
on). The driver is alerted by theflashing of the ''dipped beam'' warn-ing light on the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute. This function can only be used if the automatic switching on of the lightsmode is activated then:  with the key in the accessories position (1st notch), flash theheadlamps,
 get out of the car and lock it.
YOUR 406 COUPE IN DETAIL 103

124DRIVING YOUR 406 COUPE
AUTOMATIC AUTOADAPTIVE GEARBOX The 4-speed automaticgearbox offers the comfort of integral automatic operation ,
enhanced by a sportprogramme (switch A) and a snowprogramme (switch B).
Gear selection gate  Move the lever in the gate to select one of the positions.Once the position is selected, the indicator light for that position illuminates on
the instrument panel display.
P. Park: for immobilising the vehicle and for startingthe engine, with the hand-
brake on or off. R. Reverse: this must be engaged when the vehicle is stationary and the engine
at idle.N. Neutral: for startingthe engine and for parking, with the handbrake on.
D. Drive: for driving in autoadaptive mode (automatic changing of the four
gears).3. For driving in townor on winding roads (automatic changing of the first three
gears only).
2. For driving in the mountainsor for towing a trailer (automatic changing of
the first two gears only).
1. For use on steep gradients (selection of first gear only).
Special feature of the gearbox (2 litre petrol engine)Selection of first gear is by pressing button Cwith the lever in position 2.
To exit first gear, press button Cagain or move the selector lever.
V6 engine 2 litre engine
02-02-2004

02-02-2004
Moving Off
With the engine running, to move off from position P:
 It is essential to press the brakepedal to exit position P (shift
lock),
 Select the required position ( R, D ,
3 , 2 or 1) then gradually release
the brake pedal: the vehicle
moves off immediately.
You can also move off from position N:
 Release the handbrake with yourfoot on the brake pedal,
 Select the required position ( R, D ,
3 , 2 or 1) then gradually release
the brake pedal: the vehicle
moves off immediately. Automatic Operation Automatic changing of the
four
gears :
Move the selector lever to position D.
The gearbox continuously selects the most suitable gear according tothe following parameters:
Ð driving style,
Ð road characteristics,
Ð vehicle load.The gearbox functions in autoadap-
tive mode without any action on
your part. When the engine is idling
with position
R, D, 3, 2or
1 selected and the brakes
off, the car will move even
without you accelerating. For this reason, do not leave
children unsupervised inside the vehicle when the engine isrunning. If work needs to be done with the engine running, apply the hand-brake and select position P
.
Never select position Nwhen the
vehicle is moving. Never select position Por R
unless the vehicle is stationary .
Do not change from one position to another to optimise braking onslippery roads. In the event of battery failure, if the lever is in position Pit will not
be possible to change to anotherposition.
125
DRIVING YOUR 406 COUPE
Note: For immediate maximum acceleration
without touching the gear lever, pressthe accelerator pedal down as far as it
will go (kickdown). The gearbox willchange down automatically or stay inthe gear selected, up to maximumengine speed. When braking, the gearbox changes
down automatically to provide effi-cient engine braking.
If you take your foot off the accelera-
tor suddenly, the gearbox will not
change up for reasons of safety.

02-02-2004
Sport and Snow programmes In addition to the autoadaptive pro- gramme, two special programmes
are available. The indicator light cor-responding to the programme selec-ted lights up on the instrument panel. Sport programme Once the vehicle has been started and position Dselected, press the
S button.
The gearbox automatically favoursdynamic driving. Snow programme This programme makes starting easier
and offers smooth driving in conditions
when traction is poor.  Once the vehicle has been started and position Dselected, press the
button.
The gearbox adapts to driving onslippery roads.
Note : You can return to the autoadaptive
programme at any time.
 Press the Sor button again to
cancel the current programme. Operating anomaly Any disruption of the system is indi- cated by the alternate flashing of thesport and snow lights on the instru-ment panel. In such a case, the gearbox will operate in downgrade mode (locked
in 3rd gear). You may feel a substan-tial knock when reverse is selectedfrom position
Por N(this does not
damage the gearbox). Do not exceed 60 m.p.h. (100 km/h), if regulations permit this.
Contact a PEUGEOT dealer without
delay.
DRIVING YOUR 406 COUPE
126
MANUAL GEARBOX Reverse*
To change to reverse gear, lift the ring under the gear lever knob andpush the gear lever to the left then tothe front. Reverse gear can only be engaged when the vehicle is stationary withthe engine idling.
* According to engine.