02-02-2004
DRIVING YOUR 406 COUPE
128
THE HANDBRAKE
To apply When parking on a slope, turn the wheels towards the kerb and applythe handbrake.
To release Pull the handle and press the button to release the handbrake and movethe vehicle.
Disarming the ESP/ASR systems In certain exceptional conditions
(vehicle stuck in mud or snow, or onloose ground...), it could prove useful
to disarm the ASR and ESP systemsto make the wheels spin and regaingrip.
Press the switch "ESP OFF", sit-
uated to the left of the steering wheel.
The switch lights up and the indicatorlights come on, accompanied by themessage '' ASR/ESP de-activated''
on the multi-function display: the
ESP and ASR systems no longer
affect the operation of the engine orthe brakes. They engage again: automatically when the ignition is
switched off,
manually by pressing the switchagain. The ASR/ESP systemsoffer increased safety dur-ing normal driving, butshould not incite the driver
to take risks or to drive at highspeed. The operation of these systems is assured on condition that therecommendations of the manufac-turer regarding the wheels (tyresand wheel rims), the braking com-ponents, the electronic compo-nents and the assembly andrepair procedures within thePEUGEOT network are respected. After an accident or impact, have the system checked by a
PEUGEOT dealer.
Operating check When a system malfunctionoccurs, the switch lightflashes and the indicatorlight comes on.
Contact a PEUGEOT dealer tocheck the system.
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP) These systems are linked and com-
plement the ABS.
The ASR system optimises drive to prevent the wheels skidding, by act-ing on the brakes of the drive wheelsand on the engine. It also allows thedirectional stability of the vehicle tobe improved on acceleration. If there is a variation between the tra- jectory followed by the vehicle and
that required by the driver, the ESPsystem automatically acts on theengine and the brake of one or morewheels, in order to put the vehicleback on course.
Operation of the ASR and ESP systems
The warning light flashes if
the ASR or ESP is activated.
02-02-2004
MAINTENANCE OF YOUR 406 COUPE35
CHANGING A BULB
1 - Dipped beam headlamps
2 - Main beam headlamps
Two bulbs
(H7-55 W).
Ð Remove the red plastic cover.
Ð Press the tab and remove the protective cover corresponding to the faulty bulb.
Ð Disconnect the connector.
Ð Press the end of the securing clip to remove it. Change the bulb.
Ð When fitting, ensure that the direction notches are positioned correctly and that the securing clip is corrrectly fixed.
Ð Reconnect the connector.
Ð Replace the protective cover.
3 - Side lights (W 5 W)
Turn the socket using the lever and remove it. Change the bulb.
4 - Direction indicators (PY 21 W)
Turn the bulb holder a quarter turn and remove it. Change the bulb. Notes: only handle H7 bulbs using a dry cloth.
To replace the left-hand bulbs, remove the battery protective cover. Direction indicator repeater
(WY 5 W)
Ð Pull the rear section of the trans-
parent cover and release the
assembly.
Ð Turn the connector a quarter turn and remove it.
Ð Change the bulb.
Amber bulbs must be replaced by bulbs of iden-tical specification and
colour.
In certain climatic conditions (lowtemperatures, humidity), the
presence of condensation onthe inside of the headlampglass is normal ; it disappears a
few minutes after the lights switchon.
02-02-2004
MAINTENANCE OF YOUR 406 COUPE
36
Number plate lights (W 5 W)
Remove the translucent protector.Change the faulty bulb. Rear lights
1 - Direction indicators (P 21 W).
2 - Reversing lights (P 21 W).
3 - Brake lights/Side lights (P 21/5 W).
4 - Side lights (P 21/5 W).
5 - Fog lamp (P 21 W). These 5 bulbs are changed from inside the boot:
Ð remove the retaining clips then release the carpet,
Ð remove the connector by pressing the tab
A,
Ð remove the bulb holder by squeezing the tabs,
Ð change the faulty bulb.
