Page 3077 of 3870
Fig. 35: Removing Toe Control Arm Assembly
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
<< C>> CROSSMEMBER STAY REMOVAL The crossmember mounting bolts need not be unscrewed when the crossmember
stay is replaced. However, the bolts may be loose while the crossmember stay is
removed. It is recommended that you should retighten the bolts to 100 +/- 10 N.m (74 +
/- 7 f
t-lb
).
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor
Page 3078 of 3870
Fig. 36: Removing Crossmember Stay
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINTS >>A<< CROSSMEMBER STAY INSTALLATION Install the crossmember stay with its arrow facing the front of vehicle.
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor
Page 3079 of 3870
Fig. 37: Installing Crossmember Stay
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>B<< CROSSMEMBER STAY/CROSSMEMBER NUT INSTALLATION Ensure that the crossmember mounting bolts have been tightened to 90 - 110 N.m (67 - 81 f
t-lb
), and then install the crossmember sta
y with the crossmember nut.
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor
Page 3080 of 3870
Fig. 38: Installing Crossmember Stay/Nut
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL AND INSTALLATION < AWD>
CAUTION: For vehicles with ABS, be careful when handling the
pole piece at the tip of the ABS sensor so as not to
damage it by striking against other parts.
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor
Page 3081 of 3870
Fig. 39: Removing & Installing Rear Suspension Crossmember (AWD)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINTS << A>> REAR ABS SENSOR REMOVAL < VEHICLES WITH ABS>
CAUTION: For vehicles with ABS, be careful when handling the
pole piece at the tip of the ABS sensor so as not to
damage it by striking against other parts.
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor
Page 3083 of 3870
Fig. 41: Supporting Knuckle
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
<< C>> CROSSMEMBER STAY REMOVAL The crossmember mounting bolts need not be unscrewed when the crossmember
stay is replaced. However, the bolts may be loose while the crossmember stay is
removed. It is recommended that you should retighten the bolts to 100 +/- 10 N.m (74 +
/- 7 f
t-lb
).
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor
Page 3084 of 3870
Fig. 42: Crossmember Stay Removal
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINT >>A<< CROSSMEMBER STAY/CROSSMEMBER NUT INSTALLATION Ensure that the crossmember mounting bolts have been tightened to 90 - 110 N.m (67 - 81 f
t-lb
), and then install the crossmember sta
y with the crossmember nut.
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor
Page 3085 of 3870
Fig. 43: Installing Crossmember Stay/Nut
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSPECTION
Check the crossmember for cracks or deformation. Check all bolts for condition and straightness.
SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor
