2004 Mercury Monterey ECO mode

WARNING LIGHTS AND CHIMES
Warning lights and gauges can alert you to a vehicle condition that may
become serious enough to cause extensive repairs. A warning light may
illuminate when a problem exists with one of your vehicle’s functions.
Many lights will illuminate when you start your vehicle to make sure the
bulb works. If any light remains on after starting the vehicle, have the
respective system inspected immediately.
Check engine:TheCheck Engine
indicator light illuminates when the
ignition is first turned to the ON
position to check the bulb. Solid
illumination after the engine is started indicates the On Board
Diagnostics System (OBD-II) has detected a malfunction. Refer toOn
board diagnostics (OBD-II)in theMaintenance and Specifications
chapter. If the light is blinking, engine misfire is occurring which could
damage your catalytic converter. Drive in a moderate fashion (avoid
heavy acceleration and deceleration) and have your vehicle serviced
immediately.
Under engine misfire conditions, excessive exhaust temperatures
could damage the catalytic converter, the fuel system, interior
floor coverings or other vehicle components, possibly causing a fire.
2004 Monterey(mty)
Owners Guide (post-2002-fmt)
USA English(fus)
Instrument Cluster
Instrument Cluster
10

When the rear seat controls are activated, rear seat passengers can use
the controls to change the playing media for all passengers (Single Play
mode). In this mode, all speakers will play audio from the same media
source for all passengers to hear.
If there is a discrepancy between the rear seat controls and the front
audio controls (such as both trying to listen to the same playing media),
the front audio system will receive the desired selection.
To activate Dual Play mode (rear seat passengers listen to a different
playing media than the front seat passengers):
•Press the speaker/headphone control.
•Press MEDIA to change audio sources (for headphone mode only).
•Use the SEEK, VOLUME and MEMORY controls to make adjustments
to the playing media.
RADIO FREQUENCIES
AM and FM frequencies are established by the Federal Communications
Commission (FCC) and the Canadian Radio and Telecommunications
Commission (CRTC). Those frequencies are:
AM - 530, 540–1700, 1710 kHz
FM- 87.7, 87.9–107.7, 107.9 MHz
RADIO RECEPTION FACTORS
There are three factors that can affect radio reception:
•Distance/strength: The further you travel from an FM station, the
weaker the signal and the weaker the reception.
•Terrain: Hills, mountains, tall buildings, power lines, electric fences,
traffic lights and thunderstorms can interfere with your reception.
•Station overload: When you pass a broadcast tower, a stronger signal
may overtake a weaker one and play while the weak station frequency
is displayed.
CASSETTE/PLAYER CARE
Do:
•Tighten very loose tapes by inserting a pen or pencil into the hole and
turning the hub.
•Remove loose labels before inserting tapes.
•Allow tapes which have been subjected to extreme heat, humidity or
cold to reach a moderate temperature before playing.
2004 Monterey(mty)
Owners Guide (post-2002-fmt)
USA English(fus)
Entertainment Systems
24

with MAX A/C or can be engaged manually in any mode except Defrost.
Press to engage/disengage. To reduce humidity inside the vehicle, turn
recirculation off.
7.A/C:Press to engage/disengage. Uses outside or recirculated air to
cool the vehicle. Engages automatically in MAX A/C, Defrost and
Floor/Defrost. The A/C indicator light will illuminate in MAX A/C mode
and may or may not illuminate in Defrost, Floor/Defrost modes
depending on the previous selections.
8.Fan speed adjustment:Controls the volume of air circulated in the
vehicle.
9.Left temperature selection:Controls the temperature of the airflow
to the driver in the front of the vehicle.
10.Right temperature selection:Controls the temperature of the
airflow to the passenger in the front of the vehicle.
Operating tips
•To reduce fog build up on the windshield during humid weather, place
the air flow selector in the
position.
•To reduce humidity build-up inside the vehicle, do not drive in
recirculated air mode without the A/C running.
•Do not put objects under the front seats that will interfere with the
airflow to the back seats.
•Remove any snow, ice or leaves from the air intake area at the base of
the windshield.
To aid in side window defogging/demisting in cold weather:
1. Select
2. Select A/C
3. Set the temperature control to full heat.
4. Set the fan speed to the highest setting.
5. Direct the outer instrument panel vents towards the side windows
Do not place objects on top of the instrument panel as these
objects may become projectiles in a collision or sudden stop.
2004 Monterey(mty)
Owners Guide (post-2002-fmt)
USA English(fus)
Climate Controls
27

7.:Distributes air through the windshield defroster vents and the
floor vents. The system will automatically provide outside air to reduce
window fogging.
8.
:Distributes air through the floor vents. The system will
automatically provide outside air to reduce window fogging.
9.
:Distributes air through the instrument panel vents and the floor
ducts.
10.
:Distributes air through the instrument panel vents.
11.Manual override controls:Allows you to manually select where
airflow is directed and the fan speed. To return to full automatic control,
press AUTO.
12.
Driver heated seat control:Press to heat the driver seat. Press
once to activate high heat. Press a second time to activate low heat.
Press a third time to deactivate.
13. F
Front fan speed control:Press to increase () or decrease
(
) the fan speed.
14.
Recirculation control:Used to manually enable or disable
recirculated air operation. When activated, recirculates air in the cabin
thereby reducing the amount of time to cool down the interior of the
vehicle when used with A/C. May also help reduce undesired outside
odors from reaching the interior of the vehicle. Engages automatically
with AUTO or can be engaged manually in any mode except Defrost.
Press to engage/disengage. To reduce humidity inside the vehicle, turn
recirculation off.
15.A/C control:): Press to manually engage/disengage the air
conditioning. May engage automatically in AUTO.
16.OFF:Outside air is shut out and the fan will not operate.
17.Driver temperature control:Press to increase/decrease the
temperature to the driver in the front of the vehicle.
18.AUTO:Press to engage automatic temperature control. Select the
desired temperature using the temperature control. When in AUTO
mode, the A/C light is illuminated no matter what the temperature
setting. The system will automatically determine fan speed, airflow
location, A/C on or off, and outside or recirculated air, to heat or cool the
vehicle to reach the desired temperature.
19.REAR:Press to activate the rear climate controls.
2004 Monterey(mty)
Owners Guide (post-2002-fmt)
USA English(fus)
Climate Controls
31

7.Passenger cooled seat control:Press to cool the passenger seat.
Press once to activate high cool. Press a second time to activate low
cool. Press a third time to deactivate.
8.DUAL:(Single/dual zone electronic temperature control): Allows the
driver to have full control of the front cabin temperature settings (single
zone) or allows the passenger to have control of their individual
temperature settings (dual zone control). Press to enable and turn on a
dual zone mode, press again to return to single zone.
9.
Airflow direction control:Press to toggle through the air
distribution modes listed below. The selected mode will illuminate in the
display.
:Distributes air through the windshield defroster vents and the floor
vents. The system will automatically provide outside air to reduce
window fogging.
:Distributes air through the floor vents. The system will
automatically provide outside air to reduce window fogging.
:Distributes air through the instrument panel and the floor vents.
:Distributes air through the instrument panel.
10.
Driver heated seat control:Press to heat the driver seat. Press
once to activate high heat. Press a second time to activate low heat.
Press a third time to deactivate.
11.
Driver cooled seat control:Press to cool the passenger seat.
Press once to activate high cool. Press a second time to activate low
cool. Press a third time to deactivate.
12. F
Front fan speed control:Press to increase () or decrease
(
) the fan speed.
13.OFF:Outside air is shut out and the fan will not operate.
14.Driver temperature control:Press to increase/decrease the
temperature for the driver.
15.AUTO:Press to engage automatic temperature control. Select the
desired temperature using the temperature control. When in AUTO
mode, the A/C light is illuminated no matter what the temperature
setting. The system will automatically determine fan speed, airflow
location, A/C on or off, and outside or recirculated air, to heat or cool the
vehicle to reach the desired temperature.
16.A/C control:): Press to manually engage/disengage the air
conditioning. May engage automatically in AUTO.
2004 Monterey(mty)
Owners Guide (post-2002-fmt)
USA English(fus)
Climate Controls
33

17.REAR:Press to activate the rear climate controls.
18.
Recirculation control:Press to engage/disengage. Used to
manually enable or disable recirculated air operation. When activated,
recirculates air in the cabin thereby reducing the amount of time to cool
down the interior of the vehicle when used with A/C. May also help
reduce undesired outside odors from reaching the interior of the vehicle.
Engages automatically with AUTO or can be engaged manually in any
mode except Defrost. Press to engage/disengage. To reduce humidity
inside the vehicle, turn recirculation off.
OPERATING TIPS
Automatic fan and air distribution are set primarily by the driver
temperature settings. When the driver and passenger temperature
settings are very different, you may need to use the manual fan speed
setting to achieve passenger comfort.
•To reduce fog build up on the windshield during humid weather, place
the air flow selector in the
position.
•To reduce humidity build up inside the vehicle: do not drive with the
air flow selector in the OFF or MAX A/C position.
•Do not put objects under the front seats that will interfere with the
airflow to the back seats.
•Remove any snow, ice or leaves from the air intake area at the base of
the windshield.
To aid in side window defogging/demisting in cold weather:
1. Select
2. Select A/C
3. Modulate the temperature control to maintain comfort.
4. Set the fan speed to HI
5. Direct the outer instrument panel vents towards the side windows
Do not place objects on top of the instrument panel as these
objects may become projectiles in a collision or sudden stop.
2004 Monterey(mty)
Owners Guide (post-2002-fmt)
USA English(fus)
Climate Controls
34

Outside air temperature
The temperature can be displayed in
either Centigrade or Fahrenheit.
This is controlled via the Message
Center. Please refer to theMessage
Centerin this chapter to change
from English to metric. The ignition
key must be in the ON or ACC
position.
If the outside temperature falls
below 3°C (38°F), the display will alternate from“ICE”to the outside
temperature at a two second rate for one minute.
Compass
The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and
NW.
The compass reading may be affected when you drive near large
buildings, bridges, power lines and powerful broadcast antenna. Magnetic
or metallic objects placed in or on the vehicle may also affect compass
accuracy. Adjustments may need to be made to the zone and calibration
of the compass.
Zone variation mode
1. Determine which magnetic zone
you are in by referring to the zone
map.
2. Turn the ignition to the ON
position.
1 2 3
4
5
6 7 8 9 101112 13 14 15
2004 Monterey(mty)
Owners Guide (post-2002-fmt)
USA English(fus)
Driver Controls
50

3. Press and hold the momentary
push-button for approximately 4
seconds, until VAR is displayed,
then release it. (Pressing the
momentary push-button for 8
seconds de-calibrates the
compass—seeCompass
Calibration Mode).
4. Press the button to increment the
VAR number to the desired VAR
number. Wait 5 seconds without
button activity and the compass will return to the heading mode.
Note:If there is no button activity for 5 seconds, the compass writes the
displayed zone VAR number to memory and exits Zone Variation Mode
Compass calibration mode
1. Press the momentary push button
and hold it for more than 8 seconds.
After 8 seconds, CAL is displayed,
then release it.
Note:After button release CAL will
be displayed with a heading. The
compass is now de-calibrated and
enters the Initial AutoCal Mode.
2. Drive the vehicle in a tight circle
in a magnetically clean area such as
an open parking lot. Drive at a rate not faster than 15 seconds per circle
(5 MPH).
Note:Look for a parking lot away from buildings, light posts, manhole
covers, sewer and drainage grates and other metallic objects. Some
magnetic objects may be hidden underground. Look for signs of
underground utilities, water mains or other industrial structures. The
parking lot should be level and have a smooth surface. Blacktop is
preferred over cement as a cement surface often contains iron
reinforcing bars or metallic mesh that could interfere with the calibration
process.
•The CAL indication will turn off when the calibration process is
complete, leaving the compass heading on the display.
Note:This process normally takes about 1
1⁄2circles but may take longer
if magnetic noise is present or if the circles are driven too fast.
2004 Monterey(mty)
Owners Guide (post-2002-fmt)
USA English(fus)
Driver Controls
51