2004 MERCEDES-BENZ SL-Class Set time

99 Telephone*
Telephone operation
Refusing or ending a call
Use one of the three ways:
Press the right-hand rotary/push-
button v to confirm the “End” button.
or

Press a.
or

Press *.Accepting an incoming call using the
mobile telephone handset
The telephone is located in the storage
compartment under the armrest. See your
vehicle’s operating instructions.

Press the right-hand rotary/push-
button v to confirm the “Send” but-
ton.

Remove the telephone from its cradle
and conduct your call.
The hands-free operation will switch
off.
Ending a call

Put the phone back in its cradle.
1 Observe all legal requirementsWarning
G
Some jurisdictions prohibit the driver from
using a cellular telephone while driving a ve-
hicle. Whether or not prohibited by law, for
safety reasons, the driver should not use the
cellular telephone while the vehicle is in mo-
tion. Stop the vehicle in a safe location be-
fore answering or placing a call. If you
nonetheless choose to use the cellular pho-
ne while driving, please use the hands-free
device and be sure to pay attention to the
traffic situation at all times. Use the cellular
phone
1 only when road, weather and traffic
conditions permit.

160 NavigationDestination inputSelecting a route mode P
1Route calculated for optimum driving
time
2Route calculated for optimum driving
route
Turn the right-hand rotary/push-button
v to highlight the desired route mode
and press to confirm.Including P or avoiding Q traffic rou-
tes, several selections are available
3Calculates the route with/without free-
ways
4Calculates the route with/without ferry
connections, car trains
5Calculates the route with/without toll
roads
6COMAND calculates the route with the
selected settings

Turn the right-hand rotary/push-button
v to highlight the desired type of road
and press the button.Calculating the route

Press the right-hand rotary/push-
button v longer than 2 seconds.
or

Turn the right-hand rotary/push-button
v to highlight “OK” and press to con-
firm.
As soon as calculation begins, you will
see a corresponding message and hear
the voice output “The route is being
calculated”.
iToll roads appear in green on the map.
iIn the event that no reasonable alterna-
te route for that destination exists,
COMAND will calculate the route inclu-
ding 3 to 5 even if these selections
are to be avoided.

202Info Services*/System settingsInfo Services*

Info Services*In chapter “Info Services/System set-
tings” you will find detailed information on
the following topics:
Requesting and displaying Info Services

Adjusting the brightness

Selecting the language for the menu
text displays and the voice output

Setting the date and time

Selecting beep tones

Setting the display dimming characteri-
stics (day and night display)

Resetting all settings to the factory set-
tings

Switching an auxiliary audio source on
and offIf you have not done so already, please fa-
miliarize yourself with these functions by
reading the chapter “At a glance”
(
page 6).
When you subscribe to Info Services, you
can download information directly to your
COMAND. You can select from news, wea-
ther, sports, stocks, and calendar remin-
ders.
To personalize your selections, visit

www.MBUSA.com or call

1-800-FOR-MERCedes.
Main service menu1New information service is requested
from Response Center
2Shows date and time of the message
3The main settings menu will appear
(
page 205)
iThis function is not available in some
countries.
Requesting and displaying
Info ServicesiBefore you can use Info Services, Tele
Aid must be activated at the Response
Center and Info Services selected.

205
Info Services*/System settings
System settings

System settings
6Displays the new message
7Switches back to the main menu
There is more than one message
Press the right-hand rotary/push-
button v to move to the next page.
Activating the main service menu

Press *.
Switching back to e.g. radio main menu

Turn the right-hand rotary/push-button
v to highlight “No” and press to con-
firm.
Main system settings menu1Date and time
You can select the time format
(
page 214)
2Adjusts the brightness
3Activates “Settings” menu
4Switches an auxiliary audio source on
(page 218)
5Country setting, with a time zone
(page 210)

Press (.
The main service menu will appear.

Turn the right-hand rotary/push-button
v to highlight “System Settings” and
press to confirm.
The main system settings menu will ap-
pear.
Activating the main settings menu
iYou will see information 5 if the clock
has been set to GPS reception and if a
country, e.g. USA and a time zone was
selected.

206Info Services*/System settingsSystem settings1Previous settings
2Current settings
Press the right-hand rotary/push-
button v to confirm “Brightness”.
The “Brightness” menu will appear.Darkening screen

Turn the right-hand rotary/push-button
v to the left.
The triangle 2 will move to the left.
Brightening screen

Turn the right-hand rotary/push-button
v to the right.
The triangle 2 will move to the right.
Confirming new settings

Press the right-hand rotary/push-
button v.
The main system settings menu will ap-
pear.
Settings menu 1Selecting the language
Navigation CD must be inserted
2Setting date and time (
page 208)
3Switching beep tones on and off
(
page 215)
4Setting the display dimming characteri-
stics (day and night display)
(page 216)
5Resetting all settings to the factory set-
tings (
page 217)
Adjusting the brightness
P82.85-7710-31
2
1
Activating settings menu

208Info Services*/System settingsSystem settingsYou can select the following languages
“Adopt from Instrument Cluster”
COMAND will use the same language
as is set in instrument cluster

“Deutsch”

“English” (metric)
Distance measured in km,
speed in km/h

“English” (imperial)
Distance measured in yards and miles,
speed in miles per hour (mph)

“Español”

“Français”

“Italiano”

“Nederlands”COMAND is equipped with an integrated
clock, which it shows in the main system
settings menu.
Automatically
COMAND automatically sets date and time
if the GPS time is received.
However, you can make the following ad-
justments:
Set the time in increments of 30 minu-
tes (
page 209)

Set the time by selecting a country and
the time zone (
page 210)Manually
You must always set the clock manually
(
page 213), if

COMAND does not receive a GPS time

the clock has been disconnected from
the vehicle battery

the dates of the change between sum-
mer and winter time are not available
Setting date and timeiThe clock displays e.g. the estimated
time of arrival at the destination during
route guidance.

209
Info Services*/System settings
System settings
Setting the time in increments of 30 mi-
nutes
You can set the the time to any local time
(time zone) in increments of 30 minutes.
1COMAND receives GPS time
2Setting the clock (increments of 30 mi-
nutes)
3Selects the country and the time zone
(
page 210)
4Selects the time format (
page 214)

Turn the right-hand rotary/push-button
v to highlight “Date/Time...” in the
settings menu and press to confirm.
The menu displays the date and the
time, minutes are highlighted.Activating the setting mode

Press the right-hand rotary/push-
button v.
Setting mode is active, the minutes will
appear in red.
P82.85-7714-312
3
41
P82.85-7715-31

210Info Services*/System settingsSystem settingsAltering the time
Setting the clock ahead
Turn the right-hand rotary/push-
button v to the right.
Each click will move the time 30 mi-
nutes ahead.

Setting the clock back
Turn the right-hand rotary/push-
button v to the left.
Each click will move the time 30 mi-
nutes back.
Canceling setting mode

Press the right-hand rotary/push-
button v.
The minutes appear in black lettering.Switching back to the main system set-
tings menu

Press
*
.
or

Press the right-hand rotary/push-
button v longer than 2 seconds.
You will see the new time.
Selecting the country and the time
zone
You can select among several countries. If
a country has multiple time zones, e.g.
Canada and USA, you can select the appli-
cable time zone.
COMAND will indicate this information in
the main system settings menu.
1Input line
2Activating country list