2004 MERCEDES-BENZ G55AMG garage door opener

Contents
Transfer case ..................................... 145
Gear range ................................... 145
Switching transfer case................ 145
Differential locks ............................... 148
A few words about differentials
and differential locks.................... 149
Switching differential locks
on and off..................................... 150
Good visibility .................................... 152
Rear view mirror........................... 152
Headlamp cleaning system .......... 153
Sun visors .................................... 154
Rear window defroster ................. 155
Climate control .................................. 156
Setting the temperature ............... 158
Adjusting air distribution and
volume ......................................... 159
Defrosting .................................... 160
Air recirculation............................ 160
Residual engine heat utilization.... 161
Deactivating the climate control
system ......................................... 162
Air conditioning ............................ 162
Rear passenger compartment
adjustable air vents...................... 163Power windows .................................. 164
Opening and closing the windows. 164
Sliding/pop-up roof ............................ 166
Opening and closing the
sliding/pop-up roof....................... 166
Driving systems .................................. 169
Cruise control ............................... 169
Rear Parking Assist* ..................... 172
Loading............................................... 175
Roof rack ...................................... 175
Cargo compartment cover ............ 175
Enlarged cargo compartment........ 176
Split rear seat bench..................... 176
Partition net* (MB Accessory) ...... 178
Loading instructions ..................... 180
Cargo tie-down rings ..................... 182
Useful features ................................... 183
Interior storage spaces ................. 183
Ashtrays........................................ 186
Cigarette lighter ............................ 188
Electrical outlet ............................. 188
Telephone* ................................... 189
Tele Aid ......................................... 190
Garage door opener ...................... 198
Heated steering wheel .................. 203
Operation.......................................... 205
The first 1000 miles (1500 km) .......... 206
Driving instructions ............................ 207
Drive sensibly – save fuel ............. 207
Drinking and driving...................... 207
Pedals ........................................... 207
Power assistance .......................... 208
Brakes .......................................... 208
Driving off ..................................... 209
Parking ......................................... 209
Tires.............................................. 210
Hydroplaning ................................ 210
Tire traction .................................. 211
Tire speed rating ........................... 211
Winter driving instructions ............ 212
Standing water ............................. 213
Passenger compartment............... 213
Off-road driving ............................. 213
Control and operation of radio
transmitters .................................. 221
Driving abroad .............................. 222
Catalytic converter ....................... 222
Emission control ........................... 222
Coolant temperature .................... 223

29 At a glance
Overhead control panel
Overhead control panel
Item
Page
1
Tele Aid (emergency call
system)
190
2
Cargo compartment lamps
110
3
Right front reading lamp
109
4
Sliding/pop-up roof
166
5
Interior rear view mirror
38
Item
Page
6
Signal transmitter keys for
garage door opener
198
7
Indicator lamp for garage
door opener
198
8
Interior lighting control
109
9
Left front reading lamp
109

198 Controls in detailUseful featuresGarage door opener
The built-in remote control is capable of
operating up to three separately controlled
devices, for example garage door openers,
gate openers, or other devices compatible
with HomeLink® or some other systems.
You can program the signal transmitter
buttons.
Remote control integrated into the interior
rear view mirror1Indicator lamp
2 3 4Signal transmitter button
5Hand-held transmitter button
6Hand-held remote control trans-
mitter (not part of the vehicle
equipment)
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate op-
erator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage.
When programming a garage door opener,
the door moves up or down. When program-
ming a gate operator, the gate opens or
closes.
Do not use the integrated remote control
with any garage door opener that lacks safe-
ty stop and reverse features as required by
U.S. federal safety standards (this includes
any garage door opener model manufac-
tured before April 1, 1982). A garage door
that cannot detect an object - signaling the
door to stop and reverse - does not meet
current U.S. federal safety standards.

199 Controls in detail
Useful features
Programming or reprogramming the in-
tegrated remote control
Step 1:
Switch on ignition.
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator light be-
gins to flash after approximately 20
seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.
iCertain types of garage door openers
are incompatible with the integrated
opener. If you should experience diffi-
culties with programming the transmit-
ter, contact your authorized
Mercedes-Benz Light Truck Center, or
call Mercedes-Benz Customer Assis-
tance Center (in the USA only) at
1-800-FOR-MERCedes, or Customer
Service (in Canada) at
1-800-387-0100.
iFor operation in the USA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.


200 Controls in detailUseful featuresStep 3:
Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp1 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.Step 7:

To program the remaining two buttons,
repeat the steps above starting with
step 3.
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:

Locate “training” button on the garage
door opener motor head unit.
iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.
iIf the indicator lamp1 blinks rapidly
for about two seconds and then turns
to a constant light, continue with pro-
gramming steps 8 through 12 as your
garage door opener may be equipped
with the “rolling code” feature.


201 Controls in detail
Useful features
Exact location and color of the button
m a y v a r y b y g a r a g e d o o r o p e n e r b r a n d .
Depending on manufacturer, the “train-
ing” button may also be referred to as
“learn”or “smart” button. If there is dif-
ficulty locating the transmitting button,
refer to the garage door opener opera-
tor’s manual.
Step 9:

Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing step.
Step 10:

Firmly press, hold for two seconds and
release the programmed integrated
signal transmitter button (2, 3
or4).
Step 11:

Press, hold for two seconds and re-
lease same button a second time to
complete the training process.Some garage door openers (or other rolling
code equipped devices) may require you to
perform this procedure a third time to
complete the training.
Step 12:

Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3
or4).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner. If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:

Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has bee-
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.

357 Index
Flexible Service System (FSS) 242, 344
Fog lamp, rear 107, 296
Fog lamps, front 107
Messages in display 275
Switching on 107
4-ETS 74, 77
Front airbags 61
Front axle differential lock
Switching on 151
Front fog lamps
Replacing bulbs 295, 299
Front lamps
Messages in display 274, 276
Replacing bulbs 295, 297
Switching on 104
Front seat head restraints
Installing 95
Removing 95
Front towing eye 318
Front turn signal lamp
Replacing bulbs 300FSS (Flexible Service System) 242, 344
Fuel 225
Additives 336
Fuel reserve warning lamp 258
Gasoline additives 336
Premium unleaded gasoline 225,
333, 335
Refueling 224
Requirements 336
Reserve warning 25
Technical data 333
Fuel additives 336
Fuel consumption statistics
After start 136
Since last reset 136
Fuel filler flap 224
Locking 224
Opening 290
Unlocking 224
Fuel requirements 336Fuel reserve tank
Message in display 273
Fuel tank
Capacity 333
Filler flap 224
Fuels, coolants, lubricants, etc.
Capacities 333
Functions (control system) 116, 119
Resetting 125
Fuse box 319, 320, 321
Fuses 319
Fuse box in battery box 319
Fuse box in front passenger
footwell 320
Fuse box in middle tunnel 321
Fuse box in passenger
compartment 319
G
Garage door opener 29, 198
Gasoline see Fuel
Gasoline additives 336
GAWR 344