Page 15 of 440
15 Introduction
Symbols
Symbols
The following symbols are found in this
Operator’s Manual:
* Optional equipment is identified
with an asterisk. Since standard
equipment varies between models,
the descriptions and illustrations in
this manual may differ slightly from
the actual equipment of your
vehicle.
This symbol points to instructions for
you to follow.
A number of these symbols appearing
in succession indicates a multiple-step
procedure.
Page This symbol tells you where to
look for further information on a
topic.
This continuation symbol marks
an interrupted procedure which
will be continued on the next
page.
-> In the glossary of technical
terms, this symbol is used to in-
dicate cross-reference to term
definitions.
Display
Words appearing in the multi-
function display are printed in
the type shown here.
Warning!
G
Warning notices draw your attention to haz-
ards that may endanger your health or life,
or the health or life of others.!Highlights hazards that may result in
damage to your vehicle.iHelpful hints or further information you
may find useful.
Page 48 of 440
48 Getting startedDrivingTurn signals and high beam
The combination switch is located on the
left of the steering column.Combination switch1Turn signals, right
2Turn signals, left
Press the combination switch up1 or
down2.High beam
Push the combination switch forward.
The high beam headlights are switched
on.
The high beam symbolA in the
tachometer comes on.
For more information, see “High beam
flasher” (
page 123).
Windshield wipers
The combination switch is located on the
left of the steering column.Combination switch1Single wipe
2Switching on windshield wipers
Make sure the ignition is switched on.
iTo signal minor directional changes,
move combination switch to point of
resistance only and release. The turn
signal flashes three times.
Page 55 of 440
55 Getting started
Parking and locking
1Lock button on the door handle
After exiting the vehicle, press lock
button1 on the door handle or on the
trunk lid.
All turn signal lamps flash three times.
The locking knobs in the doors move
down. For more information, see “Locking and
unlocking” (
page 86).
!If you hear a warning signal you have
either
forgotten to switch off the vehi-
cles’s exterior lamps before open-
ing the driver’s door, or
tried to turn off the engine while the
gear selector lever is not inP.
Turn off the lights or place the gear se-
lector lever inP.
Warning!
G
To prevent possible personal injury, always
keep hands and fingers away from the door
openings when closing the doors. Be espe-
cially careful when small children are
around.
Before closing doors, make sure there is no
possibility of someone getting caught in a
door during closing.
iOpening a door causes the windows on
that side of the car to open slightly.
They will return to the up position when
the door is closed.
Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take the
SmartKey with KEYLESS-GO* with you, and
lock your vehicle. Do not leave children un-
attended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment may cause an accident
and/or serious personal injury.
Page 120 of 440
120 Controls in detailLighting
Manual headlamp mode
The low beam headlamps and parking
lamps can be switched on and off with the
exterior lamp switch. For exterior lamp
switch, see “Exterior lamp switch”
(page 119).
Automatic headlamp mode
The parking lamps, low beam headlamps
and license plate lamps switch on and off
automatically depending on the brightness
of the ambient light.
Turn the exterior lamp switch to U.
iIf you remove the SmartKey and open
the driver’s door while the parking
lamps or low beam headlamps are
switched on,
a warning sounds
$ appears in the multifunction
display
the message
Turn off lamps!
ap-
pears in the multifunction display
iWith the daytime running lamp mode
activated and the engine running, the
low beam headlamps cannot be
switched off manually.
Warning!
G
If the exterior lamp switch is set toU,
the headlamps may switch off unexpect-
edly when the system senses bright am-
bient light, for example light from
oncoming traffic.
the headlamps will not be automatically
switched on under foggy conditions.
To minimize risk to you and to others, acti-
vate headlamps by turning exterior lamp
switch to B when driving or when traffic
and / or ambient lighting conditions require
you to do so.
In low ambient lighting conditions, only
switch from position U to B with the
vehicle at a standstill. Switching from U
to B will briefly switch off the head-
lamps. Doing so while driving in low ambient
lighting conditions may result in an acci-
dent.
The automatic headlamp feature is only an
aid to the driver. The driver is responsible for
the operation of the vehicle's lights at all
times.
Page 124 of 440
124 Controls in detailLightingSwitching off the hazard warning
flasher
Press hazard warning flasher switch
again.
Interior lighting
The controls are located in the overhead
control panel.
1Rear interior lights
2Right front reading lamp
3Rocker switch for automatic control
system
4Left front reading lampActivating automatic control
Press rocker switch3 to center
position.
Interior lamps are switched on in dark-
ness, even when you:
unlock the vehicle
open a door
remove the SmartKey from the
starter switch
The interior lamps are switched off after a
preset time (
page 148).
iWith the hazard warning flasher acti-
vated and the combination switch set
for either left or right turn, only the re-
spective left or right turn signal will op-
erate when the SmartKey in the starter
switch is in position1 or2.iIf the hazard warning flasher was acti-
vated automatically, press switch1
twice.
iIf the door remains open, the interior
lamps switch off automatically after ap-
proximately five minutes when the
SmartKey is removed or in starter
switch position0.
Page 125 of 440
125 Controls in detail
Lighting
Deactivating automatic control
Press the = symbol on rocker
switch3.
The interior lighting remains switched
off in darkness, even when you:
unlock the vehicle
open a door
remove the SmartKey from the
starter switch
Manual control
Switching all front interior lights on and
off
Press the W symbol on rocker
switch3.
The front interior lights come on.
Press rocker switch3 to center
position to activate the automatic
control.Switching rear interior lights on and off
Press button V.
The lights in the rear passenger
compartment come on.
Press button V again.
The lights in the rear passenger
compartment go out.
Switching right front reading lamp on
and off
Press right button X.
The right reading lamp comes on.
Press right button X again.
The right reading lamp goes out.
Switching left front reading lamp on and
off
Press left button X.
The left reading lamp comes on.
Press left button X again.
The left reading lamp goes out.
Door entry lamps
The appropriate door entry lamp switches
on if a door is opened in darkness and if
the interior lighting is switched to automat-
ic function.
The entry lamp switches off automatically
when the door is closed.
iIf you turn the SmartKey in the starter
switch to position0 and switch off the
exterior headlamps, the door entry
lamps will remain lit for approximately
five minutes.
Page 352 of 440
352 Practical hintsReplacing bulbs
Only use 12 volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center.
Additional turn signal lamps in the
exterior rear view mirrors
High mounted brake lamp
Bi-Xenon* lamps
Front fog lamps
Replacing bulbs for front lamps
Front lamps halogen-type
1Housing cover for low beam lamp
2Housing cover for high beam lamp3Bulb socket for turn signal lamp
4Low beam bulb
5High beam bulb
6Parking and standing lamp
Page 353 of 440
353 Practical hints
Replacing bulbs
Low beam and high beam bulb
Switch off the lights.
Open the hood (
page 281).
Turn housing cover1 or 2 counter-
clockwise and remove.
Turn bulb holder 4 or 5 with the bulb
counterclockwise and remove.
Press the bulb backwards and turn
counterclockwise out of the bulb hold-
er.
Press the new bulb into the holder and
twist it clockwise.
Place the bulb holder back into the
lamp and turn it clockwise.
Place the corresponding housing cov-
ers back on and turn them clockwise.Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 281).
Twist bulb socket3 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 281).
Turn housing cover2 counterclock-
wise and remove.
Pull out the bulb socket with the bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align housing cover and click into
place.
