2004 MERCEDES-BENZ CLK55AMG CABRIOLET stop start

213 Controls in detail
Power windows

Turn the SmartKey in the starter switch
to position1or2 or press the
KEYLESS-GO* start/stop button once
or twice.Opening

Press soft top switch1 twice. Press
the switch briefly the first time. Then
press the switch a second time and
hold it until the side windows have
reached the desired position.
Closing

Pull soft top switch1 twice. Pull the
switch briefly the first time. Then pull
the switch a second time and hold it
until the side windows have reached
the desired position.Opening and closing the windows with
the SmartKey
The soft top (
page 215) will also be
opened or closed when the power windows
are operated with the SmartKey.

Aim transmitter eye at the front door
handle.
Warning!
G
Never operate the windows if there is the
possibility of anyone being harmed by the
opening or closing procedure.
In case the procedure causes potential dan-
ger, the procedure can be immediately halt-
ed by releasing the soft top switch. To
reverse direction of movement press soft
top switch twice for opening or lift soft top
switch twice for closing.
Warning!
G
Never operate the windows or soft top if
there is the possibility of anyone being
harmed by the opening or closing proce-
dure.
In the event that the procedure causes po-
tential danger, the procedure can be imme-
diately halted by releasing the button on the
SmartKey. To reverse direction of move-
ment press Œ for opening or ‹ for
closing.

218 Controls in detailSoft topOpening the soft topSoft top switch1Indicator lamp
2Soft top openingBefore pulling on the soft top switch, you
must make sure:


the parking brake is engaged
(page 46)


the luggage cover is latched, see
“Latch luggage cover” (
page 216)


the ski sack roller blind is closed, see
“Closing ski sack roller blind”
(page 217)


the trunk lid is closed


the ignition is switched on (SmartKey in
starter switch position2 or press the
KEYLESS-GO* start/stop button twice)

Pull up on the soft top switch as indi-
cated by the arrow2 until the soft top
is completely lowered into its trunk
storage compartment and the indicator
lamp1 in the soft top switch goes
out.
During the opening procedure the mul-
tifunction display shows the message Top in operation
.
If the opening procedure is finished,
the multifunction display will briefly
show the message Top open
.
If you continuously pull on the soft top
switch, the windows will close.
However, the windows can also be
closed/opened later on, for more informa-
tion see “Opening and closing the windows
with the soft top switch” (
page 212), or
see “Opening and closing the windows”
(
page 210)

220 Controls in detailSoft topBefore pressing the soft top switch, you
must make sure:

the parking brake is engaged
(page 46)


the trunk lid is closed


the ignition is switched on (SmartKey in
starter switch position2 or press the
KEYLESS-GO* start/stop button twice)

Press the soft top switch as indicated
by the arrow2 until the soft top is
completely closed and locked.The indi-
cator lamp1 in the soft top switch
goes out.
During the closing procedure the multi-
function display shows the message Top in operation
.
If the soft top is closed and locked, the
multifunction display will briefly show
the message
Top closed
.
If you continuously press on the soft
top switch the windows will close.However, the windows can also be
closed/opened later on, for more informa-
tion see “Opening and closing the windows
with the soft top switch” (
page 212) or
see “Opening and closing the windows”
(
page 210)Locking the soft top after raising/low-
ering
If the soft top is not properly locked, lock it
as described below.iFor safety reasons, the soft top cannot
be opened while driving.Warning!
G
To prevent possible accidents, drive the ve-
hicle only with the soft top either completely
closed and locked, or fully lowered into its
storage compartment.
Warning!
G
The soft top is not fully closed and locked or
not fully opened if:

the indicator lamp in the soft top switch
remains lit


the message
Top in operation!
is
shown in the multifunction display and
the indicator lamp in the soft top switch
does not go out


the indicator lamp flashes and a warning
sounds for 10 seconds and the message Lock top
is shown in the multifunction
display when starting to drive
To prevent possible accidents, drive the ve-
hicle only with the soft top either completely
closed and locked, or fully lowered into its
storage compartment.

257 Controls in detail
Useful features
Tele Aid* The Tele Aid system
(Tele
matic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response:


automatic and manual emergency


roadside assistance and


information
The Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and cel-
lular and GPS coverage is available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç.

To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.Shortly after the completion of your
Tele Aid acquaintance call, you will receive
a user ID and password via first call mail.
By visiting www.mbusa.com and selecting
“Tele Aid” (USA only), you will have access
to account information, remote door un-
lock, Info Services profile and more.
!The initial activation of the Tele Aid sys-
tem may only be performed by com-
pleting the subscriber agreement and
placing an acquaintance call using the
SOS button. Failure to complete either
of these steps will result in a system
that is not activated. If the system is
not activated, the indicator lamp in the
SOS button stays on after turning
SmartKey in starter switch to
position2 or pressing KEYLESS-GO*
start/stop button twice to position2
(page 33). The message
Tele Aid
not activated
will be shown in the
multifunction display for approximately
ten seconds.
If you have any questions regarding ac-
tivation, please call the Response Cen-
ter at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada).
iThe SOS button is located above the in-
terior rear view mirror.
The Roadside Assistance button•
and the Information button¡ are
located below the center armrest cov-
er.!The Tele Aid system utilizes the cellular
network for communication and the
GPS (Global Positioning System) satel-
lites for vehicle location. If either of
these signals is unavailable, the
Tele Aid system may not function and if
this occurs, assistance must be sum-
moned by other means.

263 Controls in detail
Useful features
Upgrade signals
The Tele Aid system processes calls using
the following priority.

Automatic emergency – First priority


Manual emergency – Second priority


Roadside assistance – Third priority


Information – Fourth priority
Should a higher priority call be initiated
while you are connected, an upgrade (al-
ternating) tone will be heard, and the ap-
propriate indicator lamp will flash. If
certain information such as vehicle identi-
fication number or customer information is
not available, the operator may need to
retransmit.
During this time you will hear a beep and
voice contact will be interrupted. Voice
contact will resume once the retransmis-
sion is completed. Once a call is conclud-
ed, a beep will be heard and the respective
indicator lamp will stop flashing. The
COMAND* system operation will resume.
!If the indicator lamps do not start flash-
ing after pressing one of the buttons or
remain illuminated (in red) at any time,
the Tele Aid system has detected a
fault or the service is not currently ac-
tive, and may not initiate a call. Visit
your authorized Mercedes-Benz Center
and have the system checked or con-
tact the Response Center at
1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada) as soon
as possible.
!If the indicator lamp continues to flash
or the system does not reset, contact
the Response Center at
1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada), or
Mercedes-Benz Customer Assistance
at 1-800-FOR-MERCedes
(1-800-367-6372) in the USA or
Customer Service at 1-800-387-0100
in Canada.iThe indicator lamp in the respective
button flashes until the call is conclud-
ed. Calls can only be terminated by a
Response Center or Customer Assis-
tance Center representative except
Roadside Assistance and Information
calls, which can also be terminated by
pressing buttonì on the multifunc-
tion steering wheel.

276 OperationDriving instructions
TiresTread wear indicators (TWI) are required by
law. These indicators are located in six
places on the tread circumference and be-
come visible at a tread depth of approxi-
mately
1⁄16 in (1.6 mm), at which point the
tire is considered worn and should be re-
placed.
The tread wear indicator appears as a solid
band across the tread.
Warning!
G
To reduce the risk of personal injury as a re-
sult of inadvertent vehicle movement, be-
fore turning off the engine and leaving the
vehicle always:

Keep right foot firmly on brake pedal.


Firmly depress parking brake pedal.


Move the gear selector lever to
position
P.


Slowly release brake pedal.


When parked on an incline, turn front
wheels towards the road curb.


Turn the SmartKey to starter switch
position
0 and remove, or press
KEYLESS-GO* start/stop button (vehi-
cles with KEYLESS-GO*).


Take the SmartKey or the SmartKey with
KEYLESS-GO* with you and lock vehicle
when leaving.
Warning!
G
If you feel a sudden significant vibration or
ride disturbance, or you suspect that possi-
ble damage to your vehicle has occurred,
you should turn on the hazard warning flash-
ers, carefully slow down, and drive with cau-
tion to an area which is a safe distance from
the road.
Inspect the tires and the vehicle underbody
for possible damage. If the vehicle or tires
appear unsafe, have it towed to the nearest
Mercedes-Benz Center or tire dealer for re-
pairs.
Warning!
G
Although the applicable federal motor vehi-
cle safety laws consider a tire to be worn
when the tread wear indicators (TWI) be-
come visible at approximately
1/16in
(1.6 mm), we recommend that you do not al-
low your tires to wear down to that level. As
tread depth approaches
1/8in (3 mm), the
adhesion properties on a wet road are
sharply reduced.
Depending upon the weather and/or road
surface (conditions), the tire traction varies
widely.

284 OperationAt the gas station
At the gas stationRefueling
The fuel filler flap is located on the
right-hand side of the vehicle towards the
rear. Locking/unlocking the vehicle with
the SmartKey or the SmartKey with
KEYLESS-GO* automatically locks/un-
locks the fuel filler flap.

Turn the engine off

by turning the SmartKey to
position0. Remove the SmartKey
from the starter switch.


by pressing the KEYLESS-GO*
start/stop button. Open the driv-
er’s door (with driver’s door open,
starter switch is now in position0,
same as with SmartKey removed
from starter switch).

Open the fuel filler flap by pushing at
the point indicated by the arrow.
The fuel filler flap springs open.

Turn the fuel cap to the left and hold on
to it until possible pressure is released.

Take off the cap and set it in the recess
on the fuel filler flap.
To prevent fuel vapors from escaping
into open air, fully insert filler nozzle
unit.

Only fill your tank until the filler nozzle
unit cuts out – do not top up or overfill.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious inju-
ry. Whenever you are around gasoline, avoid
inhaling fumes and skin contact, extinguish
all smoking materials. Never allow sparks,
flame or smoking materials near gasoline!
Failure to remove the fuel cap slowly could
result in personal injury.

289 Operation
Engine compartment
Checking engine oil level with the con-
trol system
When checking the oil level the vehicle
must

be parked on level ground


be at normal operating temperature


have been stationary for at least five
minutes with the engine turned off
To check the engine oil level via the
multifunction display, do the following:

Turn the SmartKey in the starter switch
to position2 or press the
KEYLESS GO* start/stop button twice.The standard display (
page 129) should
appear in the multifunction display.

Press buttonk or j on the
steering wheel until the following
message is seen in the multifunction
display:Engine oil level
Measuring now!
Measurement
correct
only if veh. levelOne of the following messages will
subsequently appear in the indicator:

Engine oil level
ok


Add 1.0 qt.
to reach max. oil level!(Canada:
1.0 liter
)


Add 1.5 qt.
to reach max. oil level!(Canada:
1.5 liter
)


Add 2.0 qt.
to reach max. oil level!(Canada:
2.0 liter
)

If necessary, add engine oil.
For adding engine oil see (
page 291).
More information on engine oil can be
found in the “Technical data” section
(
page 410) and (
page 412).
iIf you want to interrupt the checking
procedure, press thek orj
button on the multifunction steering
wheel.