Page 345 of 464
345 Practical hints
Where will I find...?
Vehicle jackThe vehicle jack is stored in the space un-
derneath the trunk floor together with the
vehicle tool kit in the vehicle tool kit stor-
age well casing.
Remove the vehicle jack from its com-
partment.
Push the crank handle up.
Turn the crank handle clockwise until it
engages (operational position).
Before storing the vehicle jack in its com-
partment:
It should be fully collapsed
The handle must be folded in (storage
position)
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on a level surface. Make sure the jack arm is
fully seated in the jack take-up bracket. Al-
ways lower the vehicle onto sufficient ca-
pacity jackstands before working under the
vehicle.
Page 357 of 464
357 Practical hints
Opening/closing in an emergency
Vehicles without additional locking
mechanism
Engage parking brake
Lower the side windows.
Lower rear head restraints
(page 111).
For safety reasons, remove SmartKey
from starter switch.
Open the trunk.
Lift the trunk floor cover.
Take the two straps for soft top emer-
gency operation out of vehicle tool kit
(page 343)
Take hex wrench out of the
Mercedes-Benz vehicle literature
pouch.
Open the left side trim panel in the
trunk.1Hex wrench
2Screw of hydraulic pump
Insert hex wrench 1 into screw2.
Turn hydraulic pump screw2 counter-
clockwise one revolution with hex
wrench 1.
iIf the rear head restraints cannot be
lowered, the roll bars may have been
released. For more information, see
“Operating roll bars manually”
(page 353).
!Do not operate the soft top switch with
screw2 in the opened position, other-
wise the hydraulic pump could be dam-
aged.
Page 364 of 464
364 Practical hintsOpening/closing in an emergencyVehicles with additional locking
mechanism
Engage parking brake
Lower the side windows.
Lower rear head restraints
(page 111).
For safety reasons, remove SmartKey
from starter switch.
Open the trunk.
Lift the trunk floor cover.
Take the two straps for soft top emer-
gency operation out of vehicle tool kit
(page 343)
Take hex wrench out of the
Mercedes-Benz vehicle literature
pouch.
Open the left side trim panel in the
trunk.1Hex wrench
2Screw of hydraulic pump
Insert hex wrench1 into screw2.
Turn hydraulic pump screw2 counter-
clockwise one revolution with hex
wrench1.
iIf the rear head restraints cannot be
lowered, the roll bars may have been
released. For more information, see
“Operating roll bars manually”
(page 353).
!Do not operate the soft top switch with
screw2 in the opened position, other-
wise the hydraulic pump could be dam-
aged.
Page 372 of 464
372 Practical hintsReplacing bulbs
Replacing bulbsSafe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment.
Bulbs
iIf the headlamps are fogged up on the
inside as a result of high humidity, driv-
ing the vehicle a distance should clear
up the fogging.
iBackup bulbs will be brought into use
when the following lamps malfunction:
Turn signal lamps
Brake lamps
Parking lamps
Tail lamps
Page 373 of 464
373 Practical hints
Replacing bulbs
Front lamps Rear lamps Notes on bulb replacement
Lamp
Type
1
Halogen headlamps:
Low beam
Bi-Xenon* headlamps:
Low and high beam
1
1Vehicles with Bi-Xenon headlamps* do not replace
the Bi-Xenon bulbs yourself.
H7 (55 W)
D2S-35 W
2
Halogen headlamps:
High beam/high beam
flasher
Bi-Xenon* headlamps:
High beam flasher
H7 (55 W)
H7 (55 W)
Parking and standing
lamps
W 5 W
3
Additional turn signal
lamps
LED
4
Turn signal lamp
1156 NA
5
Side marker lamp
W 5 W
6
Fog lamp
HB4/9006
(55 W)
Lamp
Type
7
Rear fog lamp, driver’s
side
P 21/4 W
Turn signal lamp
P 21 W
Brake lamp
P 21 W
Backup lamp
P 21 W
Tail, parking and stand-
ing lamp, side marker
P 21/4 W
W 5 W
8
High mounted brake
lamp
LED
9
License plate lamps
C 5 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
Page 374 of 464
374 Practical hintsReplacing bulbs
Only use 12 volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center.
Additional turn signal lamps in the
exterior rear view mirrors
High mounted brake lamp
Bi-Xenon* lamps
Front fog lamps
Replacing bulbs for front lamps
Front lamps halogen-type
1Housing cover for low beam lamp
2Housing cover for high beam lamp3Bulb socket for turn signal lamp
4Low beam bulb
5High beam bulb
6Parking and standing lamp
Page 380 of 464
380 Practical hintsFlat tire
Flat tirePreparing the vehicle
Park the vehicle as far as possible from
moving traffic on a hard surface.
Turn on the hazard warning flashers.
Engage the steering wheel lock in the
straight ahead position and set the
parking brake.
Move the gear selector lever toP.
Have any passenger exit the vehicle at
a safe distance from the roadway.
Mounting the Minispare wheelIn case of a flat tire, you may temporarily
use the spare wheel when observing the
following restrictions:
Do not exceed a vehicle speed of
50 mph (80 km/h).
Drive to the nearest tire repair facility
to have the flat tire repaired or re-
placed as appropriate.
Do not operate the vehicle with more
than one spare wheel mounted.
Prepare the vehicle as described on
(
page 380).
Take the wheel wrench and the jack
out of the trunk (
page 346).
Take the Minispare wheel and wheel
bolts out of the trunk (
page 346).
Warning!
G
The dimensions of the Minispare wheel are
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a Minispare wheel
mounted.
The spare wheel should only be used tempo-
rarily, and should be replaced with a regular
road wheel as quickly as possible.
Page 381 of 464
381 Practical hints
Flat tire
Lifting the vehicle
Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizable objects.
When changing wheel on a level surface:
Place one chock in front of and one be-
hind the wheel that is diagonally oppo-
site to the wheel being changed.
When changing wheel on a hill:
Place chocks on the downhill side
blocking both wheels of the other axle.1Wheel wrench
On wheel to be changed, loosen but do
not yet remove the wheel bolts (ap-
proximately one full turn with wrench).
The jack take-up brackets are located di-
rectly behind the front wheel housings and
in front of the rear wheel housings.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on a level surface. Make sure the jack arm is
fully seated in the jack take-up bracket. Al-
ways lower the vehicle onto sufficient ca-
pacity jackstands before working under the
vehicle.
