2004 MERCEDES-BENZ CLK500 COUPE remote start

251 Controls in detail
Useful features
Tele Aid The Tele Aid system
(Tele
matic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response:


automatic and manual emergency


roadside assistance and


information
The Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and cel-
lular and GPS coverage is available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç.

To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.Shortly after the completion of your
Tele Aid acquaintance call, you will receive
a user ID and password via first call mail.
By visiting www.mbusa.com and selecting
“Tele Aid” (USA only), you will have access
to account information, remote door un-
lock, Info Services profile and more.
!The initial activation of the Tele Aid sys-
tem may only be performed by com-
pleting the subscriber agreement and
placing an acquaintance call using the
SOS button. Failure to complete either
of these steps will result in a system
that is not activated. If the system is
not activated, the indicator lamp in the
SOS button stays on after turning
SmartKey in starter switch to
position2 or pressing KEYLESS-GO*
start/stop button twice to position2
(page 33). The message
Tele Aid
not activated
will be shown in the
multifunction display for approximately
ten seconds.
If you have any questions regarding ac-
tivation, please call the Response Cen-
ter at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada).
iThe SOS button is located above the in-
terior rear view mirror.
The Roadside Assistance button•
and the Information button¡ are
located below the center armrest cov-
er.!The Tele Aid system utilizes the cellular
network for communication and the
GPS (Global Positioning System) satel-
lites for vehicle location. If either of
these signals is unavailable, the
Tele Aid system may not function and if
this occurs, assistance must be sum-
moned by other means.

255 Controls in detail
Useful features
A voice connection between the Roadside
Assistance dispatcher and the occupants
of the vehicle will be established. When a
voice connection is established, the audio
system mutes and the message
Tele Aid
– Roadside Assistance call active
ap-
pears in the multifunction display.

Describe the nature of the need for as-
sistance.
The Mercedes-Benz Roadside assistance
dispatcher will either dispatch a qualified
Mercedes-Benz technician or arrange to
tow your vehicle to the nearest authorized
Mercedes-Benz Center. For services such
as labor and/or towing, charges may ap-
ply. Refer to the Roadside Assistance man-
ual for more information.These programs are only available in the
USA:


Sign and Drive services: Services such
as jump start, a few gallons of fuel or
the replacement of a flat tire with the
vehicle spare tire are obtainable.


Remote Vehicle Diagnostics: This func-
tion permits the Mercedes-Benz Road-
side Assistance dispatcher to
download malfunction codes and actu-
al vehicle data.iThe indicator lamp on the Roadside As-
sistance button• remains illumi-
nated in red for approximately ten
seconds during the system self-check
after turning the ignition (position2) on
(together with the SOS button and the
Information button¡).
See system self-check (
page 252)
when the indicator lamp does not come
on in red or stays on longer than ap-
proximately ten seconds.
If the indicator lamp on the Roadside
Assistance button• is illuminated
continuously and there was no voice
connection to the Response Center es-
tablished, then the Tele Aid system
could not initiate a Roadside Assis-
tance call (e.g. the relevant cellular
phone network is not available). The
message
Roadside Assistance –
Call failed
appears in the multifunc-
tion display.
Roadside Assistance calls can be ter-
minated using the ìbutton on the
multifunction steering wheel.

261 Controls in detail
Useful features
Programming or reprogramming the in-
tegrated remote control
Step 1:
Switch on ignition.
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator light be-
gins to flash after approximately 20
seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp1 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.

263 Controls in detail
Useful features
Step 12:
Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3
or4).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.
Operation of integrated remote control

Switch on ignition.

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.

264 Controls in detailUseful featuresErasing the integrated remote control
memory
Switch on ignition.

Simultaneously hold down the signal
transmitter buttons2 and 4, for ap-
proximately 20 seconds, until the indi-
cator lamp1 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (2, 3 or4). Do not re-
lease the button.

The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

412 IndexE
Easy-entry/exit feature 107
Activating 150
Interrupting movement 150
Electrical fuses 372
Electrical system
Technical data 385
Electronic Stability Program see ESP
Emergency call system* 251
Emergency calls
Initiating an emergency call 254
Telephone* 208
With Tele Aid 252
Emergency operation
(Limp Home Mode) 165
Emergency operations
Closing sliding/pop-up roof* 348
Locking the vehicle 344
Opening sliding/pop-up roof* 348
Remote door unlock 258
Unlocking the vehicle 343
Emergency tensioning device see ETD
Emission control 276
Emission control label 378Ending
A call (telephone) 155
Engine
Compartment 281
Message in display 308
Starting 44
Starting with KEYLESS-GO* 44
Starting with the SmartKey 44
Technical data 380
Turning off 53
Engine cleaning 300
Engine compartment 281
Fuse box in 373
Hood 281
Engine malfunction
indicator lamp 23, 308
Engine number 399Engine oil 283, 390
Adding 285
Additives 390
Checking level 283
Consumption 283
Filler cap 285
Filler neck 285
Message in display 326
Messages in display 284
Viscosity 399
Engine oil level see Oil level
ESP 23, 78, 399
Messages in display 318
Switching off 79
Switching on 80
Warning lamp 310, 311
ETD 399
Safety guidelines 62
ETD (Emergency tensioning device) 67
Exterior lamp switch 119
Exterior rear view mirrors
Adjusting 39
Parking position for 151

416 IndexJ
Jack 337, 339
Jump starting 366K
Key, mechanical 343
Key, SmartKey with KEYLESS-GO*
Changing the batteries 346
Key-dependency memory
Settings 151
KEYLESS-GO* 399
Activating ignition with 33
Closing side windows with 94
Closing sliding/pop-up roof*
with 94, 213, 217
Closing windows with 213, 217
Factory setting 92
Global locking 92
Global unlocking 92
Important notes 90
Locking the vehicle 93
Messages in display 328
Remote controls 89
Starting the engine 44
Turning off the engine 54
Unlocking with 32
Unlocking, trunk lid 94
Kickdown 163, 399
Kilometers/miles in speedometer 142
Km/h or mph in speedometer 142L
Labels, identification 378
Lamp bulbs, exterior 350
Lamp sensor
Messages in display 330
Lamps, exterior
Front 351
Light sensor 330
Messages in display 329–332
Rear 351
Lamps, indicator and warning
ABS 306
Battery (SmartKey) 87, 92
Brakes 307
Center console 313
CHECK ENGINE 308
Coolant 309, 322
Distance warning 310
Distronic* 223, 229
Engine diagnostics 308
ESP 310, 311

427 Index
SmartKey
Battery check lamp 87, 92
Changing the batteries 345
Checking the batteries 88, 93
Factory setting 87
Global locking 87
Global unlocking 87
Locking and unlocking 86
Loss of 89
Message in display 328
Opening and closing the
sliding/pop-up roof* with 216
Opening and closing
windows with 212
Positions in starter switch 31
Remote controls 86, 90
Restoring to factory setting 87, 92
Selective setting 87, 92
Starting the engine 44
Turning off the engine 53
Unlocking with 30SmartKey with KEYLESS-GO*
Checking the batteries 88, 93
Global locking and unlocking 92
Locking the vehicle 93
Loss of 95
Message in display 328
Messages in display 328
Remote controls 89
Restoring to factory setting 87, 92
Turning off the engine 54
Unlocking with 32
SmartKeys 86
Snow chains 295
Soft keys
Audio system 186
Spare fuses 374
Spare parts service 376
Speed
Setting current 219
Setting to last stored speed
("Resume" function)
in Distronic* 227Speed settings
Cruise control 220
Distronic* 226, 227
To last stored speed
("Resume" function)
in Cruise control 220
Speed shift 401
Speedometer 23
Displaying gear range 159
Distronic* displays 223
Settings units 142
Speedometer display mode
Selecting 142
Speedshift (CLK 55 AMG) 161
Split rear bench seat 240
SRS 66, 401
Indicator lamp 312
Standard driving
Transmission program
mode S (Sport) 163, 164
Standing lamps 119
Replacing bulbs 351, 353, 355
Standing water
Driving instructions 274