Page 345 of 464
345 Practical hints
Where will I find...?
Vehicle jackThe vehicle jack is stored in the space un-
derneath the trunk floor together with the
vehicle tool kit in the vehicle tool kit stor-
age well casing.
Remove the vehicle jack from its com-
partment.
Push the crank handle up.
Turn the crank handle clockwise until it
engages (operational position).
Before storing the vehicle jack in its com-
partment:
It should be fully collapsed
The handle must be folded in (storage
position)
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on a level surface. Make sure the jack arm is
fully seated in the jack take-up bracket. Al-
ways lower the vehicle onto sufficient ca-
pacity jackstands before working under the
vehicle.
Page 346 of 464
346 Practical hintsWhere will I find...?Minispare wheel
The Minispare wheel is located in the com-
partment underneath the trunk floor.
1Vehicle tool kit
Wheel wrench
Jack
Wheel bolts for Minispare wheel
2Arrow
3Minispare wheel
4Vehicle tool kit storage well casingRemoving the Minispare wheel
Lift trunk floor cover and engage trunk
floor handle in upper edge of trunk.
Loosen the retaining screw
(page 344) in the middle of storage
well casing.
Remove the storage well casing
(page 344).
Remove vehicle tool kit storage well
casing4.
Remove Minispare wheel3.Storing the Minispare wheel
Place Minispare wheel3 in wheel
well.
Place vehicle tool kit storage well
casing4 over the Minispare wheel.
Make sure the arrow 2 on storage
well casing4 points in the direction of
travel.
Place storage well casing
(page 344) over the vehicle tool kit
storage well casing 4 and turn the re-
taining screw (
page 344) clockwise
as far as it will go to secure the
Minispare wheel.
iThe arrow2 on vehicle tool kit stor-
age well casing4 must point in the di-
rection of travel, otherwise you cannot
place the storage well casing
(page 344) on top and secure the
Minispare wheel with the retaining
screw (
page 344).
Page 349 of 464
349 Practical hints
Unlocking/locking in an emergency
Unlocking the trunk
A minimum height clearance of 5.41 ft
(1.65 m) is required to open the trunk lid.
The lock is located next to the recessed
handle.
1Unlocking in an emergency
2Handle
Insert the mechanical key into the
trunk lid lock.
Turn the mechanical key counterclock-
wise to position1 and hold it in this
position.
Pull the trunk lid handle2 and lift the
trunk lid.
The trunk opens.
Locking the vehicle
If you are unable to lock the vehicle with
the SmartKey, lock it with the mechanical
key as follows:
Close the passenger door and the trunk
lid.
Press the central locking switch in the
cockpit (
page 108).
Check to see whether the locking knob
on the passenger door down. If neces-
sary push it down manually.
Lock the driver’s door with the me-
chanical key.
Lock the trunk lid if necessary with the
mechanical key (
page 106).
! Always make sure there is sufficient
overhead clearance.
Page 352 of 464
352 Practical hintsUnlocking/locking in an emergencyFuel filler flap
In case the central locking system does
not release the fuel filler flap, you can open
it manually.
Open trunk lid.
Remove right side trim panel in the
trunk.
Reach inside through opening2 in di-
rection of arrow.
Turn release knob 1 clockwise (ar-
row).
The fuel filler flap can be opened.Manually unlocking the gear selector
lever
In case of power failure, the gear selector
lever can be manually unlocked, e.g. to tow
the vehicle.
Open the storage compartment under
the center armrest (
page 251).
Take out cover 1.
Insert a pin into the opening of
division2 and pry the division out.
Insert a tool3 (e.g. screwdriver) into
the opening.
Perform the following two steps simul-
taneously:
Push pin3 forward in the direction
of the arrow.
Move selector lever from
positionP.
Reinstall the division and cover after re-
moving the tool from the opening.iThe gear selector lever is locked again
when moving it to positionP.
Page 353 of 464
353 Practical hints
Opening/closing in an emergency
Opening/closing in an emergency
Operating roll bars manually
Releasing roll bars manually
If the roll bar system is malfunctioning, you
can release the roll bars manually.
Close the soft top (
page 219)
Open the trunk (
page 98)
Fold back the luggage cover
(page 216).
Open ski sack roller blind
(page 217).
Take hex wrench out of the
Mercedes-Benz vehicle literature
pouch.1Perforation
Push hex wrench through
perforation1 in trim of rear wall in
trunk.
Warning!
G
If the yellow roll bar warning lamp in
the clock does not go out after starting the
engine, or if it comes on while driving, then
the roll bar system is not operating properly
and may not activate in an accident. In this
case, raise the roll bars manually before
continuing to drive.
For safety reasons drive only with the roll
bars raised until the malfunction is repaired.
Have your vehicle checked at an authorized
Mercedes-Benz Center.
iThe soft top cannot be operated after
the roll bars have been manually re-
leased.
Warning!
G
Make sure no one is located in the roll bar’s
path of motion while the next steps are be-
ing carried out.
When the roll bar is manually released, the
rear head restraints and the roll bar under-
neath shoot up almost instantaneously.
Page 357 of 464
357 Practical hints
Opening/closing in an emergency
Vehicles without additional locking
mechanism
Engage parking brake
Lower the side windows.
Lower rear head restraints
(page 111).
For safety reasons, remove SmartKey
from starter switch.
Open the trunk.
Lift the trunk floor cover.
Take the two straps for soft top emer-
gency operation out of vehicle tool kit
(page 343)
Take hex wrench out of the
Mercedes-Benz vehicle literature
pouch.
Open the left side trim panel in the
trunk.1Hex wrench
2Screw of hydraulic pump
Insert hex wrench 1 into screw2.
Turn hydraulic pump screw2 counter-
clockwise one revolution with hex
wrench 1.
iIf the rear head restraints cannot be
lowered, the roll bars may have been
released. For more information, see
“Operating roll bars manually”
(page 353).
!Do not operate the soft top switch with
screw2 in the opened position, other-
wise the hydraulic pump could be dam-
aged.
Page 361 of 464
361 Practical hints
Opening/closing in an emergency
8Windshield frame
Lift soft top out of soft top compart-
ment and pull it forward to windshield
frame8.9Opening
aLocking
Take off protective cap on the inner
side of the soft top.
Insert hex wrench into soft top locking
mechanism screw.
Turn the soft top locking mechanism
screw with hex wrench clockwise in di-
rection of arrow9 as far as it will go.
The clasp will open and the soft top will
engage audibly.
Turn the soft top locking mechanism
screw with hex wrench counterclock-
wise in direction of arrowa as far as it
will go.
The clasp will close and the soft top is
now locked onto the windshield frame.!Make sure you turn the hex wrench
counterclockwise as far as it will go.
Otherwise the soft top may not lock
properly.
Page 363 of 464
363 Practical hints
Opening/closing in an emergency
eLocking
Insert hex wrench into soft top locking
mechanism screw.
Turn the soft top locking mechanism
screw with hex wrench counterclock-
wise in direction of arrowe as far as it
will go.
The soft top is locked onto the wind-
shield frame.
Have the soft top operation checked at
your authorized Mercedes-Benz Center
as soon as possible.
Warning!
G
Position hands as indicated by arrows so
that when you press soft top compartment
cover c forward and lower material ten-
sioning frameb, your hands cannot be-
come trapped.
!Make sure you turn the hex wrench
counterclockwise as far as it will go.
Otherwise the soft top may not lock
properly.!If, after completing the soft top emer-
gency operation, the trunk cannot be
opened using the remote trunk lid re-
lease switch in the driver’s door,
theŠ button on the SmartKey, or
the trunk lid release handle in the li-
cense plate recess, press the soft top
compartment cover down again as de-
scribed above.
Do not open the trunk with the emer-
gency key, as this could otherwise
damage the trunk lid and the soft top
compartment cover.
