2004 MERCEDES-BENZ CL55AMG clock

21 At a glance
Cockpit
Item
Page
1
Combination switch

Turn signals
49


Windshield wipers
50


High beam
123
2
Cruise control lever
202


Cruise control
195


Distronic*
198
3
Instrument cluster
22
4
Multifunction steering
wheel
24
5
Gear range indicator, clock
22
6
Lever for voice control sys-
tem*, see separate operat-
ing instructions
Item
Page
7
Front Parktronic* warning
indicator for right front area
216
8
Overhead control panel
27
9
Glove box lock
221
a
Glove box lid release
221
b
Glove box
221
c
Center console
25,
26
d
Starter switch
31
e
Horn
f
Steering wheel adjustment
stalk
39
Heated steering wheel*
228
Item
Page
g
Parking brake pedal
47
h
Hood lock release
260
j
Parking brake release
47
k
Door control panel
28
l
Exterior lamp switch
119
m
Headlamp washer button
170
n
Front Parktronic* warning
indicator for left front area
216

23 At a glance
Instrument cluster
Item
Page
1
Coolant temperature gauge
127
2
Fuel gauge with:Fuel reserve warning lamp
296
3
LLeft turn signal
indicator lamp
49
KRight turn signal
indicator lamp
4
Speedometer with:vESP warning lamp
295
lDistance warning
lamp
Vehicles without Distronic*:
Warning lamp without func-
tion. It illuminates when the
ignition is on. It should go
out when the engine is run-
ning.
294
5
Tachometer
128
6
Right display with: 296
Item
Page
-Antilock Brake Sys-
tem (ABS) ndicator
lamp
292
AHigh beam headlamp
indicator
123
7
Reset button
126
8
Display with:

Program mode
163


Gear range indicator
159


Digital clock (see
COMAND operating in-
structions)
9
Multifunction display
with:

Trip odometer
129


Main odometer
129
Stored speed for:

Cruise control
195


Distronic*
198
Item
Page
a
Outside temperature indica-
tor
127
b
Left display with:1Supplemental
restraint system
indicator lamp
297
;Brake warning lamp,
USA only
293
3Brake warning lamp,
Canada only
293
?Engine malfunction
indicator lamp, USA
only
294
±Engine malfunction
indicator lamp,
Canada only
294
HTire pressure warning
lamp
275,
296
c
Knob for instrument cluster
illumination
126

104 Controls in detailLocking and unlockingSeparately locking the trunk lidThe lock is located next to the recessed
handle.
1Locked
2Neutral position

Close the trunk lid (
page 98).

Pull the mechanical key out of the
SmartKey (
page 331).

Insert the mechanical key into the
trunk lid lock.

Turn the mechanical key clockwise to
position 1.
The trunk remains locked even when the
vehicle is centrally unlocked.
Separately unlocking the trunk lid
Pull the mechanical key out of the
SmartKey (
page 331).

Insert the mechanical key into the
trunk lid lock.

Turn the mechanical key counterclock-
wise to neutral position 2, see above.
You can now open the trunk (
page 96).
A minimum height clearance of 6 ft.
(1.85 m) is required to open the trunk lid.
iYour vehicle may be equipped with a
function permitting the separate lock-
ing of the trunk using the mechanical
key. If present, this feature can permit
you to deny any unauthorized person
access to the trunk by locking the trunk
separately and leaving the SmartKey
less the mechanical key with the vehi-
cle.
To verify the presence of this feature,
use the mechanical key to lock the
trunk and then attempt to open the
trunk by pressing the trunk lid lock af-
ter the vehicle has been centrally un-
locked with the SmartKey.
iYou can only cancel the separate trunk
locking mode by means of the
mechanical key.Warning!
G
Only drive with the trunk closed as, among
other dangers such as visibility blockage,
exhaust fumes may enter the vehicle interi-
or.

126 Controls in detailInstrument cluster
Instrument clusterA full view illustration of the instrument
cluster can be found in the “At a glance”
section of this manual (
page 22).
The instrument cluster is activated when
you:


open a door


turn on the ignition


press the reset button (
page 22)


switch on the exterior lamps
You can change the instrument cluster set-
tings in the Instrument cluster submenu of
the control system (
page 148).
Instrument cluster illumination
1Knob for adjusting instrument cluster
illumination
Use knob1 to adjust the illumination
brightness for the instrument cluster.

Press knob1.
The knob will pop out.
To brighten illumination

Turn knob1 in the instrument cluster
clockwise.
The instrument cluster illumination will
brighten.
To dim illumination

Turn knob1 in the instrument cluster
counterclockwise.
The instrument cluster illumination will
dim.
iThe instrument cluster illumination is
dimmed or brightened automatically to
suit ambient light conditions.
The instrument cluster illumination will
also be adjusted automatically when
you switch on the vehicle’s exterior
lamps.

330 Practical hintsWhere will I find...?Vehicle jack
To prepare the vehicle jack for use
Remove the vehicle jack from the spare
wheel well under the trunk floor.

Push the crank handle up.

Turn the crank handle clockwise until it
engages (operational position).
Storing the vehicle jack in the trunk

Retract the vehicle jack arm to the
base of the vehicle jack.

Push the crank handle up.

Turn the crank handle counterclock-
wise to the end of the stop (storage po-
sition).Spare wheel
Removing the spare wheel

Take out vehicle tool kit tray 2.

Turn the luggage bowl 3 counter-
clockwise.

Remove the spare wheel 4.
Storing the spare wheel

Place spare wheel 4 in wheel well and
secure it with luggage bowl 3.

Turn the luggage bowl 3 clockwise to
its stop.

Place vehicle tool kit tray 2 in luggage
bowl 3.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Make sure the jack arm is
fully seated in the jack take-up bracket. Al-
ways lower the vehicle onto sufficient ca-
pacity jackstands before working under the
vehicle.

332 Practical hintsUnlocking/locking in an emergencyUnlocking the trunk
A minimum height clearance of 6.3 ft
(1.90 m) is required to open the trunk lid.
If you are unable to unlock the trunk with
the SmartKey or KEYLESS-GO*, open the
trunk with the mechanical key.
The trunk lid lock is located above the rear
license plate recess.
1Unlocking and opening
2Trunk lid lock
Insert the mechanical key into the
trunk lid lock2.

Turn the mechanical key counterclock-
wise to position1 and press trunk lid
lock2 in direction of arrow.
The trunk unlocks and opens.
Locking the vehicle
If you are unable to lock the vehicle with
the SmartKey or the SmartKey with
KEYLESS-GO*, lock it with the mechanical
key as follows:
Close the passenger door and the trunk
lid.

Press the central locking switch in the
center console (
page 106).

Check to see whether the locking knob
on the passenger door is still visible. If
necessary push it down manually.

Slide mechanical key2 out of the
SmartKey (
page 331).

Lock the driver’s door with the me-
chanical key (
page 331).

Lock the trunk lid necessary with the
mechanical key (if applicable)
(page 104).
Replacing batteries in the SmartKey/
SmartKey with KEYLESS-GO*
If the batteries in the SmartKey or the
SmartKey with KEYLESS-GO* are dis-
charged, the vehicle can no longer be
locked or unlocked. It is recommended to
have the batteries replaced at an autho-
rized Mercedes-Benz Center.
!The trunk lid swings open upwards au-
tomatically. Always make sure that
there is sufficient overhead clearance.
Warning!
G
Keep the batteries out of reach of children.
If a battery is swallowed, seek medical help
immediately.

335 Practical hints
Opening/closing in an emergency
Opening/closing in an emergency
Sliding/pop-up roof
You can open or close the sliding/pop-up
roof manually should an electrical malfunc-
tion occur.
The driving mechanism for the slid-
ing/pop-up roof is located behind the lens
of the interior overhead light.
1Lens

Pry off lens1 using a flat blade screw-
driver (
page 329).

Turn the SmartKey in the starter switch
to position1 or2.

Remove the crank from the operator’s
manual pouch.
2Crank

Insert crank2 through hole.

Turn crank2 clockwise to:

close slide roof


raise roof at the rear

Turn crank2 counterclockwise to:

open slide roof


lower roof at the rear
The sliding/pop-up roof must be resyn-
chronized after being operated manually
(
page 194).

339 Practical hints
Replacing bulbs

Insert the new bulb so that the base lo-
cates in the recess on the holder.

From below, press connector2 with
bulb upward onto the reflector.

Align housing cover1 and click into
place.
Front turn signal bulb

Switch off the lights.

Open the hood (
page 260).

Twist bulb socket4 counterclockwise
and pull out.

Gently push bulb into socket, turn
counterclockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb

Switch off the lights.

Open the hood (
page 260).

Press ends of housing cover1 tab to-
gether and remove cover.

Pull out the bulb socket with the bulb.

Pull the bulb out of the bulb socket.

Insert a new bulb in the socket.

Reinstall the bulb socket.

Align housing cover and click into
place.Side marker lamp bulb

Switch off the lights.

Carefully slide lamp towards rear.

Remove front end first.

Twist bulb socket counterclockwise
and pull out.

Pull bulb out of the bulb socket.

Insert new bulb in socket.

Reinstall bulb socket, push in and twist
clockwise.

To reinstall lamp, set rear end in
bumper and let front end snap into
place.