2004 MERCEDES-BENZ C320 COUPE remote control

216 Controls in detailUseful featuresProgramming or reprogramming the in-
tegrated remote control
Step 1:
Switch on ignition.
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator light be-
gins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp1 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after
20 seconds.

218 Controls in detailUseful featuresStep 12:
Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3
or4).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.
Operation of integrated remote control

Switch on ignition.

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.


219 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on ignition.

Simultaneously hold down the signal
transmitter buttons2 and 4, for ap-
proximately 20 seconds, until the indi-
cator lamp1 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (2, 3 or4). Do not re-
lease the button.

The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

233 Operation
At the gas station
At the gas station
RefuelingThe fuel filler flap is located on the
right-hand side of the vehicle towards the
rear. Locking/unlocking the vehicle with
the remote control automatically
locks/unlocks the fuel filler flap.

Turn off the engine

Remove the SmartKey from the starter
switch.

Open the fuel filler flap by pushing at
the point indicated by the arrow.
The fuel filler flap springs open.

Turn the fuel cap to the left and hold on
to it until possible pressure is released.

Take off the cap and set it in the recess
on the fuel filler flap.
To prevent fuel vapors from escaping
into open air, fully insert filler nozzle
unit.

Only fill your tank until the filler nozzle
unit cuts out – do not top up or overfill.

Replace the fuel cap by turning it to the
right.
You should hear the fuel cap engage.

Close the fuel filler flap.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious inju-
ry. Whenever you are around gasoline, avoid
inhaling fumes and skin contact, extinguish
all smoking materials. Never allow sparks,
flame or smoking materials near gasoline! Warning!
G
Flexible Fuel Vehicles (identified by a label
reading Premium gasoline or E85 only! on
fuel filler flap):
Ethanol fuel (E85) and its vapors are highly
flammable, poisonous and burn easily. Etha-
nol fuel can cause serious injuries if ignited
or if you come into contact with it or inhale
fumes of it. Avoid inhalation of Ethanol
fumes and skin contact with Ethanol. Extin-
guish all open flames before refueling. Never
smoke or create sparks close to Ethanol.
Warning!
G
Overfilling of the fuel tank may create pres-
sure in the system which could cause a gas
discharge. This could cause the gas to spray
back out when removing the fuel pump noz-
zle, which could cause personal injury.


354 Index
Safety systems 73
Through standing water 229
Driving abroad 230
Driving instructions 223
Driving off 225
Driving safety systems
ABS 73
BAS 74
ESP 75
Driving systems 194
Cruise control 194
Driving safety systems 73
E
Easy-entry/exit feature 89
Activating 130
Interrupting movement 89, 130
Electrical fuses 317
Electrical system
Technical data 327
Electronic Stability Program
see ESP 23, 75, 342Emergency call system* 206
Emergency calls
Initiating an emergency call 209
Telephone* 184
With Tele Aid* 208
Emergency operation
(Limp Home Mode) 145
Emergency operations
Closing sliding/pop-up roof 292
Locking the vehicle 289
Opening sliding/pop-up roof 292
Remote door unlock 213
Unlocking the vehicle 288
Emergency release
Trunk lid 86
Emergency tensioning device
see ETD 64, 342
Emission control 231
Emission control label 322
Ending
A call (telephone) 135Engine
Compartment 236
Message in display 260
Starting with
automatic transmission 45
Starting with manual
transmission 44
Starting with the key 45
Technical data 324
Turning off with the key 53
Engine cleaning 253
Engine compartment 236
Fuse box in 317
Hood 236
Engine malfunction
indicator lamp 23, 260
Engine number 342
Engine oil 237, 332
Adding 239
Additives 332
Checking level 237
Consumption 237
Display messages 275
Filler neck 240

358 IndexImmobilizer 78
Activating 78
Deactivating 78
Infant and child restraint systems 65
Installing 69
LATCH child seat mounts 70
Inflating
Spare tire 304
Information
Button for Tele Aid* 211
Installing
Infant and child restraint systems 69
Towing eye bolt 316
Wiper blades 300
Instrument cluster 22, 105, 343
Cleaning 255
Coolant temperature indicator 106
Illumination 105
Lamps in 261–262
Multifunction display 109Outside temperature indicator 107
Selecting language 124
Instruments and controls see Cockpit 20
Interior lighting 103
Activating automatic control 103
Deactivating automatic control 103
Delayed shut-off 128
Manual operation 103
Interior rear view mirror
Adjusting 39
Antiglare 146
Interior storage spaces 200
Armrest 202
Cup holder 201
Glove box 200
Parcel net in
front passenger footwell 203
Storage compartment in
front of armrest 201J
Jack 285, 286
Jump starting 310
K
Key dependency memory
Settings 131
Key positions in starter switch 31
Key, mechanical 288, 289
Key, SmartKey
Battery check lamp 83
Changing the batteries 290
Checking the batteries 84
Factory setting 83
Global locking 83
Global unlocking 83
Individual setting 83
Loss of 84
Positions in starter switch 31
Remote controls 82
Restoring to factory setting 83

365 Index
Removing 93
Rear seats
Adjusting head restraint height 91
Rear view mirror automatic antiglare 146
Rear view mirrors see Mirrors
Rear window defroster 149
Activating 149
Deactivating 149
Reconnecting
Vehicle battery 308
Refrigerant
Air conditioner 332
Refuelling 233
Regular checks 234
Reinstalling vehicle battery 308
Remote controls
SmartKey 82
Remote door unlock
With Tele Aid* 213
Remote Vehicle Diagnostics 344Removing
Vehicle battery 308
Wheel 303
Wiper blades 300
Replacing
Backup lamp bulbs 298
Brake lamp bulbs 298
Bulbs 293
Front lamp bulbs 295
Front turn signal bulbs 295, 296
High beam bulbs 295
High beam bulbs
(xenon-type headlamps) 296
License plate lamp bulbs 299
Low beam bulbs 295
Parking lamp bulbs 296, 297
Rear fog lamp bulbs 298
Rear lamp bulbs 294, 298
Rear turn signal bulbs 298
Side marker lamp bulbs 298
Standing lamp bulbs 296, 297Wiper blades 300
Reset button in
the instrument cluster 119
Reset knob in
the instrument cluster 119, 120
Resetting
All functions (control system) 119
All functions of a submenu 120
Fuel consumption 133
Service indicator (FSS) 250
Trip odometer 107
Residual heat utilization 344
REST
(Residual engine heat utilization) 344
Restraint system see
Infant and child restraint systems 65, 69Reverse (manual transmission)
Shifting into 138
Rims 325
Roadside assistance
Tele Aid* 210
Roller sunblind for the sliding/pop-up roof
Closing 189
Opening 189