2004 MAZDA MODEL SPEED MX-5 MIATA reset

6-44
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L

Clock
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock ’s current time will flash.
2. To advance the hours, press the hour set button ( ). To advance the minutes,
press the minute set button ( ) while
the time is flashing.
3. Press the clock button ( ) again to start the clock. Exact hour adjustment1. To set the exact hour, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock ’s current time will flash.
2. Press the clock button ( ) again and the time will be adjusted as
follows:
(Example)
12:01 —12:29
→12:00
12:30 —12:59
→1:00
Display Clock button
Hour set
button
Minute set
button
NOTE
If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle ’s battery is disconnected), the
clock will need to be reset.
J07S_8T02-EA-03L_Edition1.book Page 44 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-46
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L

Operating the Radio
Radio ON
Press a band selector button ( or
) to turn the radio on.
Band selection
Choose AM by pressing the AM button
( ) and FM by pressing the FM1/2
button ( ).
The selected mode will be indicated. If
FM stereo is being received, "ST" will be
displayed. Tu n i n g
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Turning the manual tuning dial will
change the frequency higher or lower.
Band selector buttons Display
Channel preset buttons
Scan button
Auto memory
button
Manual tuning dial Seek tuning
button
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STEREO to MONO for reduced
noise, and the "ST" indicator will go
out.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
J07S_8T02-EA-03L_Edition1.book Page 46 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-47
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L
Seek tuning
Pressing the seek tuning button
( , ) will cause the tuner to seek a
higher or lower frequency automatically.
Scan tuning
Press the scan button ( ) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, merely press
the scan button ( ) again during this
interval.
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.
1. To set a channel first select AM, FM1, or FM2. Tune to the station you want.
2. Depress a channel preset button for about 2 seconds until a beep is heard.
The preset channel number and station
frequency will be displayed. The
station is now held in the memory.
3. Repeat this operation for the other stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its
channel preset button. The station
frequency and the channel number will
be displayed. Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known. Additional AM/FM stations can
be stored without disturbing the
previously set channels.
Press and hold the auto memory button
( ) for about 2 seconds until a beep
is heard; the system will automatically
scan and temporarily store up to 6 stations
with the strongest frequencies in each
selected band in that area.
After scanning is completed, the station
with the strongest frequency will be tuned
and its frequency displayed.
Press and release the auto memory button
( ) to recall stations from the auto-
stored stations. One stored station will be
selected each time; its frequency and
channel number will be displayed.
NOTE
If you continue to press and hold the
button, the frequency will continue
changing without stopping.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
NOTE
If no stations can be tuned after
scanning operations, "A" will be
displayed.
J07S_8T02-EA-03L_Edition1.book Page 47 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-54
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L

Operating the In-Dash CD Changer*
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed. Normal insertion
1. Press the load button ( ).
2. When "In" is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the desired tray number within 3 seconds
after the beep is heard.
3. When "In" is displayed, insert the CD.
Disc-in indicator
CD ejectbutton
Scan
button Track up
button
Track down
button
Disc down
button
Load button
Random button
Repeat button
Disc up button Reverse button
Fast-forward
button
Channel preset buttons
Display
CD slot
CD play button
NOTE
A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this waiting
time. Simultaneously pressing the
power/volume dial and the load button
( ) for about 2 seconds will turn
this beeping sound ON or OFF.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
*Some models.
J07S_8T02-EA-03L_Edition1.book Page 54 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-55
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L
Multiple insertion
1. Press and hold the load button ( ) for about 2 seconds until a beep is
heard.
2. When "In" is displayed, insert the CD.
3. When "In" is displayed again, insert the next CD.
Ejecting the CD
Normal ejection
1. Press the CD eject button ( ). The disc number and "OUT" will be
displayed.
2. Pull out the CD.
Ejecting CDs from desired tray number
1. Press and hold the CD eject button ( ) for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the desired CD number within 3 seconds
after the beep is heard.
3. Pull out the CD. Multiple ejection
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Wait 3 seconds or press the CD eject button ( ) again within 3 seconds
after the beep is heard.
3. Pull out the CD, then the next CD will be ejected.
Playing
Press the CD play button ( ) to start
playing when a CD is in the unit.
Fast-forward/Reverse
Press and hold the fast-forward button
( ) to advance through a track at high
speed.
Press and hold the reverse button ( )
to reverse through a track at high speed.
Tr a c k s e a r c h
Press the track up button ( ) once to
skip forward to the beginning of the next
track.
Press the track down button ( ) once to
skip back to the beginning of the current
track.
NOTE
The first-inserted CD will be played
automatically when:
• No other CD is inserted within 15
seconds after "In" is displayed.
• The CD trays are full.
NOTE
When the CD is ejected during play,
the next CD will be played
automatically.
NOTE
•CDs will be ejected starting with the
one with the lowest number.
• All CDs in the tray will be ejected
continuously.
• CDs can be ejected when the
ignition switch is off. Press and hold
the CD eject button ( ) for about 2
seconds and all CDs will eject.
J07S_8T02-EA-03L_Edition1.book Page 55 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI