2004 MAZDA MODEL SPEED MX-5 MIATA brakes

8-9
Maintenance and Care
Scheduled Maintenance
Form No. 8T02-EA-03L
I:Inspect: Inspect and clean, repair, adjust, or replace if necessary.
R: Replace
T: Tighten
EMISSION CONTROL SYSTEM
ELECTRICAL SYSTEM
CHASSIS and BODY
*5 This is a full function check of electrical systems such as lights, wiper and washer systems (including wiper blades), and power windows.
*6 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is operated in extremely humid climates, change the brake fluid annually.
Maintenance
Interval
(Number of
months or
kilometers (miles),
whichever
comes first) Months 6 121824303642485460667278849096
× 1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
× 1000 miles
6.25 12.5 18.752531.25 37.5 43.755056.25 62.5 68.757581.25 87.5 93.75100
Evaporative system IIIIIIII
All electrical system
*5IIIIIIII
Brake pedals and clutch pedals IIIIIIIIIIIIIIII
Brake lines, hoses and
connections IIIIIIII
Clutch fluid IIIIIIIIIIIIIIII
Brake fluid
*6IIIRIIIRIIIRIIIR
Parking brake IIIIIIIIIIIIIIII
Power brake unit and hoses IIIIIIII
Disc brakes IIIIIIIIIIIIIIII
Power steering fluid and lines IIIIIIIIIIIIIIII
Steering operation and gear
housing IIIIIIII
Steering linkages, tie rod ends
and arms IIIIIIII
Manual transmission oil R
Rear differential oil RR
Front and rear suspension and
ball joints IIII
Automatic transmission fluid
level IIIIIIII
Drive shaft dust boots IIII
Bolts and nuts on chassis and
body TTTTTTTT
Body condition (for rust,
corrosion and perforation)
(except Australian model) Inspect annually
Exhaust system heat shields Inspect every 80,000 km (50,000 miles)
Tire (including spare tire)(with
inflation pressure adjustment) IIIIIIII
J07S_8T02-EA-03L_Edition1.book Page 9 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-18
Maintenance and Care
Owner Maintenance
Form No. 8T02-EA-03L

Inspecting Brake Fluid Level
Inspect the fluid level in the reservoir
regularly. It should be kept at MAX.
The level normally drops with
accumulated distance, a condition
associated with wear of brake linings. If it
is excessively low, have the brake system
inspected by an Authorized Mazda
Dealer.

Adding Brake Fluid
If the fluid level is low, add fluid until it
reaches MAX.
Before adding fluid, thoroughly clean the
area around the cap.
Brake Fluid
Spilled Brake Fluid:
Spilled brake fluid is dangerous. If it
gets in your eyes, they could be
seriously injured. If this happens,
immediately flush your eyes with
water and get medical attention.
Brake fluid spilled on a hot engine
could cause a fire. Be careful not to
spill brake fluid on yourself or on the
engine.
Low Brake Fluid Levels:
Low brake fluid levels are dangerous.
Low levels could signal brake lining
wear or a brake system leak. Your
brakes could fail and cause an
accident. If you find a low fluid level,
have the brakes inspected.
• Brake fluid will damage painted
surfaces. If brake fluid does get on
a painted surface, wipe it off
immediately.
• Using nonspecified brake fluids
(page 10-4) will damage the system.
Mixing different fluids will also
damage it.
If the brake system frequently
requires new fluid, consult an
Authorized Mazda Dealer.
WARNING
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 18 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-43
Maintenance and Care
Appearance Care
Form No. 8T02-EA-03L
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the fenders, and make
sure the drain holes in the lower edges of
the doors and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming. Wa x i n g
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.
Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for metallic, mica, and solid colors.
3. When waxing, coat evenly with the sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.

Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn
’t need it.
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
CAUTION
J07S_8T02-EA-03L_Edition1.book Page 43 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-44
Maintenance and Care
Appearance Care
Form No. 8T02-EA-03L

Bright-Metal Maintenance
• Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
• To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
• During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.


Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also to
do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.
Don
’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may result in
damage to the protective coating and
cause discoloration or paint
deterioration.
CAUTION
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
J07S_8T02-EA-03L_Edition1.book Page 44 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

11-2
Form No. 8T02-EA-03L
Index
A
Add-On Non-Genuine Parts and
Accessories
...................................... 9-12
Air Bag Systems
.............................. 2-20
Air Filter
.......................................... 8-24
Antenna
.............................................. 6-9
Anti-Lock Brake System (ABS)
........ 5-7
Warning light
.............................. 5-8
Appearance Care
.............................. 8-40
Ashtray
............................................. 6-60
Audio System
..................................... 6-9
Audio set
......................... 6-17, 6-37
Operating tips for audio
system
......................................... 6-9
Safety certification
.................... 6-58
Automatic Transmission Driving tips
............................... 5-14
Fluid
.......................................... 8-21
Overdrive
.................................. 5-13
Shift-lock override
.................... 5-12
Shift-lock system
...................... 5-12
Transmission ranges
................. 5-11
B
Battery Emergency starting
................... 7-13
Maintenance
............................. 8-27
Specifications
........................... 10-4
Beep Sounds Ignition key reminder
............... 5-30
Lights-on reminder
................... 5-30
Seat belt warning beep
.............. 5-30
Before Starting the Engine
................. 4-6
After getting in
........................... 4-6
Before getting in
......................... 4-6
Body Lubrication
............................. 8-23
Brake Fluid
.......................................... 8-18
B
BrakesAnti-lock brake system (ABS)
....5-7
Foot brake
................................... 5-4
Pad wear indicator
...................... 5-8
Parking brake
.............................. 5-5
Warning light
.............................. 5-6
Break-In Period
.................................. 4-7
Bulb Replacement
............................ 8-32
C
Capacities ......................................... 10-5
Carbon Monoxide
.............................. 4-5
Catalytic Converter
............................ 4-4
Cell Phones
...................................... 9-13
Center Console
................................. 6-62
Child Restraint Child restraint precautions
........ 2-13
LATCH child-restraint
systems
...................................... 2-18
Cigarette Lighter
.............................. 6-60
Climate Control System
.....................6-2
Gas specification
....................... 10-5
Clutch Fluid
.......................................... 8-19
Convertible Top
............................... 3-18
Cruise Control
.................................. 5-15
Cup Holder
....................................... 6-61
Customer Assistance
.......................... 9-2
D
Dashboard Illumination .................... 5-22
Daytime Running Lights
.................. 5-33
Defroster Rear window
............................. 5-35
Detachable Hardtop
.......................... 3-23
Dimensions
....................................... 10-5
J07S_8T02-EA-03L_Edition1.book Page 2 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI