2004 MAZDA MODEL SPEED MX-5 MIATA change time

6-32
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L

Operating the In-Dash CD Changer*
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number, the track number and
the elapsed play back time for the current
track will be displayed.
Display CD slot
Disc-in indicator
CD ejectbutton
CD play button
Random button
Repeat button
Disc up button Scan
button
Fast-forward
button
Reverse button
Track up
button
Track down
button
Disc down
button
Load button
Power/Volume dial
Channel preset buttons
NOTE
•When the clock is displayed, the
elapsed play back time will not be
displayed. To display the elapsed
play back time, turn the audio
control dial to the right. Turn the
dial to the left to return to the
previous display.
• A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this
waiting time. Simultaneously
pressing the power/volume dial and
the load button ( ) for about 2
seconds will turn this beeping sound
ON or OFF.
*Some models.
J07S_8T02-EA-03L_Edition1.book Page 32 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-45
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L
Changing the display mode
The display on the unit can be changed by
pressing the clock button ( ). This
alternates the display between time and
audio. When the clock mode has been
selected, the time will be displayed.
NOTE
If audio operation is selected while the
time mode is on, the selected audio
mode will be displayed for 10 seconds,
then the display will revert to the time
mode.
J07S_8T02-EA-03L_Edition1.book Page 45 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

6-54
Interior Comfort
Au di o S ys t em
Form No. 8T02-EA-03L

Operating the In-Dash CD Changer*
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed. Normal insertion
1. Press the load button ( ).
2. When "In" is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the desired tray number within 3 seconds
after the beep is heard.
3. When "In" is displayed, insert the CD.
Disc-in indicator
CD ejectbutton
Scan
button Track up
button
Track down
button
Disc down
button
Load button
Random button
Repeat button
Disc up button Reverse button
Fast-forward
button
Channel preset buttons
Display
CD slot
CD play button
NOTE
A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this waiting
time. Simultaneously pressing the
power/volume dial and the load button
( ) for about 2 seconds will turn
this beeping sound ON or OFF.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
*Some models.
J07S_8T02-EA-03L_Edition1.book Page 54 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-17
Maintenance and Care
Owner Maintenance
Form No. 8T02-EA-03L
To change coolant
1. Remove the cooling system cap.
2. Only when the engine is cool, remove the radiator drain plug and drain the
coolant into a suitable container.
Properly dispose of the used coolant.
3. Flush out the system with running water. 4. Drain the system completely. Insert
and tighten the plug. Add as much
ethylene-glycol-based coolant mixture
and water as necessary to provide
freezing and corrosion protection.
5. In extremely cold climates, add the mixture percentage recommended in
the coolant mixture percentage table.
6. Run the engine at idle with the cooling system cap off. Slowly add additional
coolant if necessary.
7. At this point, wait until the engine reaches normal operating temperature;
then depress the accelerator two or
three times. Add more coolant, if
necessary, until the system is full.
8. Install the cooling system cap. Inspect all connections for leaks. Inspect the
level in the coolant reservoir one more
time.
Removing the Cooling System Cap:
Removing the cooling system cap
while the engine is running or hot is
dangerous. This might lead to cooling
system and engine damage and could
result in serious injury from escaping
hot coolant or steam. Turn off the
engine and wait until it ’s cool. Even
then, be very careful when removing
the cap. Wrap a thick cloth around
the cap and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you ’re sure all the pressure is
gone, press down on the cap — still
using a cloth — turn the cap, and
remove it.
WARNING
Tighten
Loosen
Tighten Loosen
J07S_8T02-EA-03L_Edition1.book Page 17 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI

8-23
Maintenance and Care
Owner Maintenance
Form No. 8T02-EA-03L
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
Use plain water if washer fluid is
unavailable.
But use only washer fluid in cold weather
to prevent it from freezing.All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the engine hood
’s secondary
latch keeps the hood from opening when
the primary latch is released.
Type A
Type B
Body Lubrication
J07S_8T02-EA-03L_Edition1.book Page 23 Monday, November 10, 2003 11:21 AM
Black process 45.0 ° 240.0 LPI