2004 MAZDA MODEL RX 8 brake

8-32
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C
3. Install the new bulb in the reverse order
of removal.
Trunk light
1. Press both sides of the lens cap to
remove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of removal.

Replacing a Bulb (Rear)
Rear turn signal lights, Brake lights/
Taillights, Reverse lights
1. Pull the center section of the plastic
retainer and remove the retainers and
partially open the trunk side trim.2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of removal.
Rear side-marker lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
High-mount brake light
1. Turn the center section of the plastic
retainer counterclockwise and remove
the retainers and trunk rear trim.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
Removal
InstallationTrunk side trim
Rear turn signal lights
Brake lights/Taillights
Reverse lights
Socket
Removal
Installation
Trunk rear trim
J60E_8R65-EA-03C_Edition2.book Page 32 Saturday, April 26, 2003 1:48 PM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8R65-EA-03C
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
19 IG 30AFor protection
of various
circuits
20 IG KEY 15AFor protection
of various
circuits
21 STOP 15A Brake lights
22 FUEL PUMP 20A Fuel pump
23 HORN 15A Horn
24 HAZARD 15AHazard warning
flashers, Turn
signals
25 ETV 15AElectric throttle
valve
26 WIPER 20AWindshield
wiper and
washer
27 P.WIND 20A Power windows
28 ENGINE 15AEngine control
system,
Supplemental
restraint
system, ABS,
Power steering
29 TAIL 10ATaillights,
License plate
light,
Parking lights,
Front side-
maker lights,
Rear side-
marker lights
30 ILLUMI 10AIlluminated
entry system
31 EGI COMP1 10AEngine control
system
32 EGI COMP2 10AEngine control
system
33 EGI INJ 15A Fuel injector
34 EPS 60A Power steering
J60E_8R65-EA-03C_Edition2.book Page 37 Saturday, April 26, 2003 1:48 PM

8-42
Maintenance and Care
Appearance Care
Form No. 8R65-EA-03C
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the fenders, and make
sure the drain holes in the lower edges of
the doors and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.
Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colors.
3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.

Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn’t need it.
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 42 Saturday, April 26, 2003 1:48 PM

8-43
Maintenance and Care
Appearance Care
Form No. 8R65-EA-03C

Bright-Metal Maintenance
•Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
•To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
•During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.

Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also to
do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.

The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting. Don’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may result in
damage to the protective coating and
cause discoloration or paint
deterioration.
CAUTION
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
J60E_8R65-EA-03C_Edition2.book Page 43 Saturday, April 26, 2003 1:48 PM

10-5
Specifications
Form No. 8R65-EA-03C


Lubricant Quality
*Refer to the recommended SAE viscosity numbers on page 8-9.


Capacities
(Approximate Quantities)
Check oil and fluid levels with dipsticks or reservoir gauges.


Dimensions
*With license plate holder
LubricantClassification
API Service ILSAC
Engine oil
*SL GF-III
Lubricant Classification
Manual transmission oil API Service GL-4 or GL-5 (SAE 75W-90)
Automatic transmission fluid ATF M-III or equivalent (e.g. Dexron® III)
Rear differential oil API Service GL-5 (SAE 90)
Brake/Clutch fluid SAE J1703 or FMVSS116 DOT-3
ItemUnit
L US qt Imp qt
Engine oilWith oil filter replacement 3.5 3.7 3.1
Without oil filter replacement 3.3 3.5 2.9
Coolant 9.8 10.4 8.6
Manual transmission oil 1.75 1.8 1.5
Automatic transmission fluid 8.7 9.2 7.7
Rear differential oil 1.3 1.4 1.1
Fuel tank 60 15.9 (US gal) 13.2 (Imp gal)
Item Model
Overall length
4,425 mm (174.2 in), 4,430 mm
*(174.4 in)
Overall width 1,770 mm (69.7 in)
Overall height 1,340 mm (52.8 in)
Front tread 1,500 mm (59.1 in)
Rear tread 1,505 mm (59.3 in)
Wheelbase 2,700 mm (106.3 in)
10.fm Page 5 Friday, July 4, 2003 11:46 AM

10-6
Specifications
Form No. 8R65-EA-03C

We i g h t s

Air Conditioner

Light Bulbs
Exterior light
The rear side-marker light bulbs cannot be replaced because they are an LED-type bulb.
The rear combination component must be replaced.
Interior light
ItemWe i g h t
Manual transmission Automatic transmission
GVWR (Gross Vehicle Weight Rating) 1,728 kg (3,809 lb) 1,748 kg (3,854 lb)
GAWR (Gross Axle Weight Rating)Front 827 kg (1,823 lb) 841 kg (1,854 lb)
Rear 901 kg (1,986 lb) 907 kg (2,000 lb)
CW (Curb Weight)USA 1,374 kg (3,029 lb) 1,385 kg (3,053 lb)
Canada 1,384 kg (3,051 lb) 1,394 kg (3,073 lb)
Gas complies with SAE J639 Maximum operating charge
HFC134a (R-134a) 0.42 kg (14.8 oz)
Light bulb WattageCategory
ECE R SAE
HeadlightsHigh beam 65 H9—
Low beamHalogen 55 H7—
Xenon fusion 35 D2S—
Front turn signal lights 21 WY21W—
Parking lights 5 W5W—
Fog lights
*55 H11—
Front side-marker lights 3.8—#194
High-mount brake light 21 W21W #7440
Rear turn signal lights 21 WY21W—
Brake lights/Taillights 21/5 W21/5W #7443
Reverse lights 21 W21W #7440
License plate light 5 W5W—
Rear side-marker lights 0.57——
Light bulb WattageCategory
ECE R
Trunk light 5 W5W
Overhead light/Map lights (Front) 5 W5W
Overhead light (Rear) 10—
Courtesy lights 5 W5W
Vanity mirror lights 1.8—
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 6 Saturday, April 26, 2003 1:48 PM

11-2
Form No. 8R65-EA-03C
Index
A
Accessory Socket ............................. 6-48
Add-On Non-Genuine Parts and
Accessories
...................................... 9-12
Air Bag Systems
.............................. 2-27
Air Filter
.......................................... 8-18
Ambient Temperature Display
........ 6-41
Antenna
............................................ 6-10
Anti-Lock Brake System (ABS)
........ 5-7
Warning light
.............................. 5-7
Appearance Care
.............................. 8-39
Ashtray
............................................. 6-43
Audio System
................................... 6-10
Audio control switch
................ 6-34
Audio set
................................... 6-17
Operating tips for audio
system
....................................... 6-10
Safety certification
.................... 6-36
Automatic Transmission
Driving tips
............................... 5-15
Fluid
.......................................... 8-15
Manual shift mode
.................... 5-11
Shift-lock system
...................... 5-11
Transmission ranges
................. 5-10
B
Battery
Emergency starting
................... 7-20
Maintenance
............................. 8-21
Specifications
........................... 10-4
Beeps
Engine overrev warning
beep
........................................... 5-47
Ignition key reminder
............... 5-47
Lights-on reminder
................... 5-47
Seat belt warning beep
.............. 5-47
Tire inflation pressure warning
beep
........................................... 5-47
B
Before Starting the Engine ................. 4-6
After getting in
............................ 4-6
Before getting in
......................... 4-6
Body Lubrication
............................. 8-18
Brake/Clutch
Fluid
.......................................... 8-14
Brakes
Anti-lock brake system (ABS)
....5-7
Foot brake
................................... 5-4
Pad wear indicator
...................... 5-8
Parking brake
.............................. 5-5
Warning light
.............................. 5-5
Break-In Period
.................................. 4-7
Bulb Replacement
............................ 8-27
C
Capacities ......................................... 10-5
Carbon Monoxide
.............................. 4-5
Catalytic Converter
............................ 4-3
Cell Phones
...................................... 9-13
Center Console
................................. 6-46
Child Restraint
Child restraint precautions
........ 2-17
Installing child-restraint
systems
...................................... 2-20
LATCH child-restraint
systems
...................................... 2-25
Cigarette Lighter
.............................. 6-42
Climate Control System
.....................6-2
Gas specifications
..................... 10-6
Clock
................................................ 6-41
Coin Box
.......................................... 6-45
Courtesy Lights
................................ 6-39
Cruise Control
.................................. 5-17
Cup Holder
....................................... 6-44
Customer Assistance
.......................... 9-2
J60E_8R65-EA-03C_Edition2.book Page 2 Saturday, April 26, 2003 1:48 PM

11-3
Index
Form No. 8R65-EA-03C
D
Dashboard Illumination ................... 5-34
Daytime Running Lights
.................. 5-49
Defroster
Rear window
............................. 5-53
Dimensions
...................................... 10-5
Door Locks
......................................... 3-7
Driving In Flooded Area
.................. 4-10
Driving Tips
....................................... 4-7
Automatic transmission
............ 5-15
Break-in period
........................... 4-7
Driving in flooded area
............. 4-10
Hazardous driving
....................... 4-8
Money-saving suggestions
.......... 4-7
Rocking the vehicle
.................... 4-8
Winter driving
............................. 4-9
Dynamic Stability Control (DSC)
.... 5-21
DSC OFF indicator light
........... 5-22
DSC OFF switch
....................... 5-23
TCS/DSC Indicator light
.......... 5-22
E
Emergency Starting .......................... 7-20
Flooded engine
.......................... 7-20
Jump-starting
............................ 7-20
Push-starting
............................. 7-22
Emergency Towing
.......................... 7-23
Emission Control System
................... 4-3
Engine
Coolant
...................................... 8-12
Exhaust gas
................................. 4-5
Hood release
............................. 3-18
Oil
............................................... 8-9
Overheating
............................... 7-18
Starting
........................................ 5-3
Engine Compartment Overview
........ 8-8
Engine Coolant
Overheating
............................... 7-18
E
Engine Coolant Temperature
Gauge
...............................................5-32
Exhaust Gas
........................................4-5
Exterior Care
....................................8-41
F
Flasher
Hazard warning
.........................5-55
Headlights
.................................5-48
Flat Tire
..............................................7-3
Changing
...................................7-13
Instant Mobility System (IMS)
Emergency Flat Tire Repair
Kit
................................................7-5
Spare tire and tool storage
...........7-3
Fluids
Classification
.............................10-5
Owner maintenance
.....................8-6
Fog Lights
........................................5-50
Foot Brake
..........................................5-4
Front seats
..........................................2-2
Fuel
Filler lid and cap
.......................3-16
Gauge
........................................5-33
Requirements
..............................4-2
Tank capacity
............................10-5
Fuses
.................................................8-33
Panel description
.......................8-36
Replacement
..............................8-33
G
Gauges ..............................................5-29
Glove Box
........................................6-45
J60E_8R65-EA-03C_Edition2.book Page 3 Saturday, April 26, 2003 1:48 PM