2004 MAZDA MODEL 6 HATCHBACK warning light

Black plate (271,1)
Also, inspect them for uneven wear and
damage. Abnormal wear is usually caused
by one or a combination of the following:
lIncorrect tire pressure
lImproper wheel alignment
lOut-of-balance wheel
lSevere braking
After rotation, inflate all tire pressures to
specification (page 10-6) and inspect the
lug nuts for tightness.
CAUTION
Rotate unidirectional tires and radial
tires that have an asymmetrical tread
pattern or studs only from front to rear,
not from side to side. Tire performance
will be weakened if rotated from side to
side.
qReplacing a Tire
WARNING
Worn Tires:
Driving with worn tires is dangerous.
Reduced braking, steering, and
traction could result in an accident.
Always use tires that are in good
condition.If a tire wears evenly, a wear indicator
will appear as a solid band across the
tread.
Replace the tire when this happens.
New treadTread wear indicator
Worn tread
You should replace it before the band is
across the entire tread.
qTemporary Spare Tire
Inspect the temporary spare tire at least
monthly to make sure it's properly inflated
and stored.
The temporary spare tire is easier to
handle because of its construction. It is
lighter and smaller than a conventional
tire and should be used only for an
emergency and only for a short distance.
Use the temporary only until the
conventional tire is repaired, which should
be as soon as possible.
Maintain its pressure at 420 kPa (4.2 kgf/
cm
2or bar, 60 psi).
Maintenance and Care
Owner Maintenance
8-29
Mazda6_8T12-EA-03K_Edition1 Page271
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (272,1)
CAUTION
lDon't use your temporary spare tire
rim with a snow tire or a
conventional tire. Neither will
properly fit and could damage both
tire and rim.
lThe temporary spare tire has a tread
life of up to 5,000 km (3,000 miles),
depending on road conditions and
driving habits.
lThe temporary spare tire is for
limited use, however, if the tread
wear solid-band indicator appears,
replace the tire with the same type of
temporary spare (page 8-29).
qReplacing a Wheel
WARNING
Using a Wrong-Sized Wheel:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident. Always use
wheels of the correct size on your
vehicle.
CAUTION
A wrong-sized wheel may adversely
affect:
lTire fit
lWheel and bearing life
lGround clearance
lSpeedometer calibration
lHeadlight aim
lBumper height
When replacing a wheel, make sure the
new one is the same as the original factory
wheel in diameter, rim width, and offset.
Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and flat spots.
8-30
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page272
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (274,1)
Your Mazda's headlights and fog lights
have replaceable halogen bulbs.
WARNING
Handling Halogen Bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries could
be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Never touch the glass portion of the
bulb with your bare hands and always
wear eye protection when handling or
working around halogen bulbs.
Children and Halogen Bulbs:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
Always keep halogen bulbs out of the
reach of children.
qReplacing Exterior Light Bulbs
Replacing the headlight, fog light andparking light bulbs
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
Front turn signal lights
1. Turn the socket and bulb assembly
counterclockwise and remove it.2. Remove the bulb by pushing it in
slightly and turning it
counterclockwise.
Socket
3. Install the new bulb in the reverse order
of removal.
Side-marker lights
1. Turn the screw counterclockwise and
remove it, then partially peel back the
mudguard.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
8-32
Maintenance and Care
Owner Maintenance
Mazda6_8T12-EA-03K_Edition1 Page274
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (288,1)
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don't allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
WARNING
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
Dry the brakes by driving very slowly
and applying the brakes lightly until
brake performance is normal.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.
Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colors.3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn't need it.
qRepairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.
CAUTION
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
qBright-Metal Maintenance
lUse tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
lTo prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
lDuring cold weather or in coastal areas,
cover bright-metal parts with a coating
of wax or preservative heavier than
usual. It would also help to coat them
with noncorrosive petroleum jelly or
some other protective compound.
8-46
Maintenance and Care
Appearance Care
Mazda6_8T12-EA-03K_Edition1 Page288
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (289,1)
CAUTION
Don't use steel wool, abrasive cleaners,
or strong detergents containing highly
alkaline or caustic agents on chrome-
plated or anodized aluminum parts.
This may result in damage to the
protective coating and cause
discoloration or paint deterioration.
qUnderbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also
to do this every month.
Pay special attention to these areas
because they easily hide mud and dirt.It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.
WARNING
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
Dry the brakes by driving very slowly
and applying the brakes lightly until
brake performance is normal.
qAluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
NOTE
lDon't use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
lOnly use a mild soap or neutral
detergent and always use a sponge or
soft cloth to clean the wheels.
Rinse thoroughly with lukewarm or
cold water. Also, be sure to clean the
wheels after driving on dusty or
salted roads. This helps prevent
corrosion.
lAvoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
lIf your aluminum wheels lose luster,
wax the wheels.
Maintenance and Care
Appearance Care
8-47
Mazda6_8T12-EA-03K_Edition1 Page289
Friday, December 5 2003 8:59 AM
Form No.8T12-EA-03K

Black plate (320,1)
A
Accessory Socket .............................. 6-55
Add-On Non-Genuine Parts and
Accessories ....................................... 9-13
Air Bag Systems ............................... 2-43
Air Filter ............................................ 8-20
Ambient Temperature Display .......... 6-47
Antenna ............................................. 6-16
Anti-Lock Brake System (ABS) ......... 5-7
Warning light ............................... 5-7
Appearance Care ............................... 8-43
Ashtray .............................................. 6-49
Audio System ................................... 6-16
Audio control switch .................. 6-40
Audio set .................................... 6-23
Operating tips for audio
system ........................................ 6-16
Safety certification ..................... 6-42
Automatic Transaxle
Driving tips ................................ 5-15
Fluid ........................................... 8-17
Manual shift mode ..................... 5-12
Shift-lock system ........................ 5-11
Transaxle ranges ........................ 5-10
B
Battery
Emergency starting .................... 7-16
Maintenance ............................... 8-26
Specifications ............................. 10-3
Beep sounds
Ignition key reminder ................. 5-37
Lights-on reminder ..................... 5-37
Seat belt warning beep ............... 5-37
Before Starting the Engine .................. 4-6
After getting in ............................. 4-6
Before getting in .......................... 4-6
Body Lubrication .............................. 8-19
B
Bottle Holder ..................................... 6-51
Brake/Clutch
Fluid ........................................... 8-15
Brakes
Anti-lock brake system (ABS) ..... 5-7
Foot brake .................................... 5-4
Pad wear indicator ........................ 5-8
Parking brake ............................... 5-5
Warning light ............................... 5-6
Break-In Period ................................... 4-7
Bulb Replacement ............................. 8-31
C
Capacities .......................................... 10-4
Carbon Monoxide ............................... 4-5
Cargo Securing Loops ...................... 6-53
Cargo Sub-Compartment .................. 6-54
Catalytic Converter ............................. 4-3
Cell Phones ....................................... 9-14
Center Box ........................................ 6-52
Center Console .................................. 6-52
Child Restraint
Installing child-restraint
systems ....................................... 2-31
LATCH child-restraint
systems ....................................... 2-38
Child Safety Locks for Rear Doors ..... 3-9
Cigarette Lighter ............................... 6-48
Climate Control System ...................... 6-2
Gas specifications ...................... 10-5
Clock ................................................. 6-47
Courtesy Lights ................................. 6-45
Cruise Control ................................... 5-16
Cup Holder ........................................ 6-50
Customer Assistance ........................... 9-2
11-2
Index
Mazda6_8T12-EA-03K_Edition1 Page320
Friday, December 5 2003 9:0 AM
Form No.8T12-EA-03K

Black plate (321,1)
D
Dashboard Illumination .................... 5-26
Daytime Running Lights ................... 5-39
Defroster
Rear window .............................. 5-42
Dimensions ....................................... 10-4
Door Locks ......................................... 3-7
Driving In Flooded Area ................... 4-10
Driving Tips ........................................ 4-7
Automatic transaxle ................... 5-15
Break-in period ............................ 4-7
Driving in flooded area .............. 4-10
Hazardous driving ........................ 4-8
Money-saving suggestions ........... 4-7
Rocking the vehicle ...................... 4-8
Winter driving .............................. 4-9
E
Emergency Starting ........................... 7-16
Flooded engine ........................... 7-16
Jump-starting .............................. 7-17
Push-starting .............................. 7-19
Emergency Towing ........................... 7-20
Emission Control System .................... 4-3
Engine
Coolant ....................................... 8-12
Exhaust gas .................................. 4-5
Hood release .............................. 3-26
Oil .............................................. 8-10
Overheating ................................ 7-14
Starting ......................................... 5-3
Engine Compartment Overview .......... 8-9
Engine Coolant
Overheating ................................ 7-14
Engine Coolant Temperature
Gauge ................................................ 5-25
Exhaust Gas ........................................ 4-5
Exterior Care ..................................... 8-45
F
Flasher
Hazard warning .......................... 5-44
Headlights .................................. 5-38
Flat Tire ............................................... 7-3
Changing ...................................... 7-8
Spare tire and tool storage ............ 7-3
Fluids
Classification .............................. 10-3
Owner maintenance ..................... 8-7
Fog Lights ......................................... 5-40
Foot Brake .......................................... 5-4
Front Seats
(Electrically Operated Seats) ............... 2-5
Front Seats
(Manually Operated Seats) ................. 2-2
Fuel
Filler lid and cap ........................ 3-24
Gauge ......................................... 5-26
Requirements ............................... 4-2
Tank capacity ............................. 10-4
Fuses ................................................. 8-38
Panel description ........................ 8-40
Replacement ............................... 8-38
G
Glove Box ......................................... 6-52
H
Hatch ................................................. 3-10
Luggage compartment cover ...... 3-11
Luggage strap ............................. 3-11
Hazard Warning Flasher .................... 5-44
Hazardous Driving .............................. 4-8
Index
11-3
Mazda6_8T12-EA-03K_Edition1 Page321
Friday, December 5 2003 9:0 AM
Form No.8T12-EA-03K

Black plate (322,1)
H
Headlights
Control ....................................... 5-38
Flashing ...................................... 5-38
High-low beam .......................... 5-38
On reminder ............................... 5-38
HomeLink Wireless Control
System .............................................. 5-44
Hood Release .................................... 3-26
Horn .................................................. 5-43
I
Ignition
Keys ............................................. 3-2
Switch .......................................... 5-2
Illuminated Entry System ................. 6-43
Immobilizer System .......................... 3-29
Indicator Lights ................................. 5-28
Cruise Main ................................ 5-36
Cruise set .................................... 5-36
Headlight high-beam .................. 5-34
Security ...................................... 5-34
Shift position .............................. 5-35
TCS ............................................ 5-35
TCS OFF .................................... 5-35
Turn-signal/hazard warning ....... 5-36
Information Display .......................... 6-46
Ambient temperature display ..... 6-47
Audio display ............................. 6-48
Climate control display .............. 6-48
Clock .......................................... 6-47
Display dimmer cancel
function ...................................... 6-48
Information display functions .... 6-46
Instrument Cluster ............................. 5-23
Instrument Cluster Dimmer Select
Button ............................................... 5-26
Interior Care ...................................... 8-48
I
Interior Lights ................................... 6-43
J
Jump-Starting .................................... 7-17
K
Keyless Entry System ......................... 3-3
Keys .................................................... 3-2
L
Label Information ............................. 10-2
Lane-Change Signals ........................ 5-39
Trunk Release lever ........................... 3-21
Liftgate .............................................. 3-12
Luggage compartment cover ...... 3-14
Luggage compartment net .......... 3-15
Light Bulbs
Replacement ............................... 8-31
Specifications ............................. 10-5
Lighter ............................................... 6-48
Lighting Control ............................... 5-38
Lubricant Quality .............................. 10-3
Luggage Compartment Light ............ 6-45
M
Maintenance
Introduction .................................. 8-2
Owner maintenance precautions ... 8-8
Owner maintenance schedule ....... 8-7
Scheduled ..................................... 8-3
Manual Transaxle Operation ............... 5-8
Recommendations for shifting ..... 5-9
Map Lights ........................................ 6-44
11-4
Index
Mazda6_8T12-EA-03K_Edition1 Page322
Friday, December 5 2003 9:0 AM
Form No.8T12-EA-03K