2004 MAZDA MODEL 3 5-DOOR tire pressure

7-11
In Case of an Emergency
Flat Tire
Form No. 8S18-EA-03I
4. Turn the jack handle counterclockwise and lower the vehicle. Use the lug
wrench to tighten the nuts in the order
shown.
If you ’re unsure of how tight the nuts
should be, have them inspected at an
Authorized Mazda Dealer.
Nut tightening torque:
N·m (kgf ·m, ft ·lbf) 88 —117 (9—11, 65 —93)
Loose Lug Nuts:
Improperly or loosely tightened lug
nuts are dangerous. The wheel could
wobble or come off. This could result
in loss of vehicle control and cause a
serious accident. Always securely and
correctly tighten the lug nuts.
Metric Studs and Lug Nuts:
Because the wheel studs and lug nuts
on your Mazda have metric threads,
using a non-metric nut is dangerous.
On a metric stud, it would not secure
the wheel and would damage the stud,
which could cause the wheel to slip
off and cause an accident. Be sure to
reinstall the same nuts you removed
or replace them with metric nuts of
the same configuration.
Incorrect Tire Air Pressure:
Driving on tires with incorrect air
pressure is dangerous. Tires with
incorrect pressure could affect
handling and result in an accident.
Don ’t drive with any tires that have
incorrect air pressure. When you
check the regular tires ’ air pressure,
check the spare tire, too.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 11 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

7-12
In Case of an Emergency
Flat Tire
Form No. 8S18-EA-03I
5. Store the damaged tire, using the tire hold-down bolt to hold it in place.
Have the damaged tire repaired as soon
as possible.
NOTE
(With Tire Pressure Monitoring
System)
A tire pressure sensor is not installed
to the temporary spare tire. The
warning light will flash continuously
while the temporary spare tire is being
used (page 5-23).
NOTE
To prevent the jack and tool from
rattling, store them properly.
Tire clamp Tire hold-down bolt
J48C_8S18-EA-03I_Edition3.book Page 12 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-6
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I
I: Inspect and repair, clean, adjust, or replace if necessary.
R : Replace
L : Lubricate
CHASSIS and BODY
Maintenance Interval
(Number of months or kilometers (miles),
whichever comes first)Months 4 8 12 16 20 24 28 32 36 40 44 48
× 1000 km 8 16 24 32 40 48 56 64 72 80 88 96
× 1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Brake lines, hoses and connections II
Brake and clutch fluid level IIIIIIIIIIII
Disc brakes IIII
Tire (rotation) Rotate every 8,000km (5,000miles)
Tire inflation pressure and tire wear IIIIIIIIIIII
Steering operation and linkages II
Power steering fluid level IIIIIIIIIIII
Front and rear suspension and ball
joints II
Driveshaft dust boots II
Exhaust system and heat shields Inspect every 72,000km (45,000miles) or 60 months
All locks and hinges LLLLLLLLLLLL
Washer fluid level IIIIIIIIIIII
J48C_8S18-EA-03I_Edition3.book Page 6 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-9
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I
I: Inspect: Inspect and clean, repair, adjust, or replace if necessary.
R : Replace
T : Tighten
*5:This is a full function check of electrical systems such as lights, wiper and washer systems (including wiper blades), and power windows.
Maintenance
Interval
(Number of months or
kilometers
(miles), whichever comes first)Months 6 121824303642485460667278849096
× 1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
×1000 miles6.25 12.518.752531.2537.543.755056.2562.568.757581.2587.593.75100
Power steering fluid, lines,
hoses and connections IIIIIIIIIIIIIIII
Steering operation and
linkage IIIIIIII
Manual transaxle oil R
Automatic transaxle fluid
level IIIIIIII
Front and rear suspension and
ball joints IIII
Driveshaft dust boots IIII
Exhaust system and heat
shields Inspect every 80,000km (50,000miles)
Bolts and nuts on chassis and
body TTTTTTTT
All electrical system
*5IIIIIIII
Body condition (for rust,
corrosion and perforation) Inspect annually
Tires (including spare
tire)(with inflation pressure
adjustment) IIIIIIII
J48C_8S18-EA-03I_Edition3.book Page 9 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-10
Maintenance and Care
Form No. 8S18-EA-03I
Owner Maintenance
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.

When Refueling
• Brake and clutch fluid level (page 8-18)
• Engine coolant level (page 8-15)
• Engine oil level (page 8-13)
• Washer fluid level (page 8-21)


At Least Monthly
• Tire inflation pressures (page 8-31)


At Least Twice a Year (For Example, Every Spring and Fall)
• Automatic transaxle fluid level (page 8-20)
• Power steering fluid level (page 8-19)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
• Air filter (page 8-23)
• Engine coolant (page 8-15)
• Engine oil (page 8-14)
Owner Maintenance Schedule
J48C_8S18-EA-03I_Edition3.book Page 10 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-31
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tire inflation pressures and
stay within the recommended load limits
and weight distribution.

Tire Inflation Pressure
The Tire Pressure Monitoring System*
does not alleviate the need to check the
tire condition every day, including
whether the tires all look inflated
properly. Inspect all tire pressure monthly
(including the spare) when the tires are
cold. Maintain recommended pressures
for the best ride, top handling, and
minimum tire wear.
Refer to the specification charts (page
10-8).
Tires
Using Different Tire Types:
Driving your vehicle with different
types of tires is dangerous. It could
cause poor handling and poor
braking; leading to loss of control.
Except for the limited use of the
temporary spare tire, use only the
same type tires (radial, bias-belted,
bias-type) on all four wheels.
Using Wrong-Sized Tires:
Using any other tire size than what is
specified for your Mazda (page 10-8)
is dangerous. It could seriously affect
ride, handling, ground clearance, tire
clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tires that
are the correct size specified for your
Mazda.
WARNING
Incorrect Tire Inflation:
Overinflation or underinflation of
tires is dangerous. Adverse handling
or unexpected tire failure could result
in a serious accident. Always inflate
the tires to the correct pressure (page
10-8).
WARNING
Tire pressure label
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 31 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-32
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Tire Rotation
To equalize tread wear, rotate the tires
every 12,000 km (7,500 miles)/8,000 km*
(5,000 miles) or sooner if irregular wear
develops. During rotation, inspect them
for correct balance.
*Unique driving conditions for USA,
Canada and Puerto Rico
Also, inspect them for uneven wear and
damage. Abnormal wear is usually caused
by one or a combination of the following:
• Incorrect tire pressure
• Improper wheel alignment
• Out-of-balance wheel
• Severe braking
After rotation, inflate all tire pressures to
specification (page 10-8) and inspect the
lug nuts for tightness.
NOTE
• Always check tire pressure when
tires are cold.
• Warm tires normally exceed
recommended pressures. Don
’t
release air from warm tires to adjust
the pressure.
• Underinflation can cause reduced
fuel economy and poor sealing of
the tire bead, which will deform the
wheel and cause separation of tire
from rim.
• Overinflation can produce a harsh
ride and a greater possibility of
damage from road hazards.
Keep your tire pressure at the
correct levels. If one frequently
needs inflating, have it inspected.
Rotate unidirectional tires and radial
tires that have an asymmetrical tread
pattern or studs only from front to rear,
not from side to side. Tire performance
will be weakened if rotated from side
to side.
Front
Do not include (TEMPORARY USE ONLY)
spare tire in rotation.
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 32 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-33
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Replacing a TireIf a tire wears evenly, a wear indicator will
appear as a solid band across the tread.
Replace the tire when this happens.
You should replace it before the band is
across the entire tread.

Temporary Spare Tire
Inspect the temporary spare tire at least
monthly to make sure it
’s properly
inflated and stored.
The temporary spare tire is easier to
handle because of its construction. It is
lighter and smaller than a conventional
tire and should be used only for an
emergency and only for a short distance.
Use the temporary only until the
conventional tire is repaired, which should
be as soon as possible.
Maintain its pressure at 420 kPa (4.2 kgf/
cm
2 or bar, 60 psi).
Worn Tires:
Driving with worn tires is dangerous.
Reduced braking, steering, and
traction could result in an accident.
Always use tires that are in good
condition.
(With Tire Pressure Monitoring
System)
When replacing/repairing the tires or
wheels or both, have the work done by
an Authorized Mazda Dealer, or the
tire pressure sensors may be damaged.
NOTE
(With Tire Pressure Monitoring
System)
• When tires with steel wire
reinforcement in the sidewalls are
used, the system may not function
correctly even with a genuine
wheel. (page 5-24)
• Be sure to install the tire pressure
sensors whenever tires or wheels are
replaced. (page 5-24)
WARNING
CAUTIONNew tread
Worn tread
Tread wear indicator
J48C_8S18-EA-03I_Edition3.book Page 33 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI