2004 MAZDA MODEL 3 5-DOOR climate control

6-7
Interior Comfort
Climate Control System
Form No. 8S18-EA-03I

Heating
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the hot position.
3. Set the fan control dial to the desired speed.

Cooling (With Air Conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the cold position.
3. Set the fan control dial to the desired speed.
4. Turn on the air conditioner.
5. Adjust the fan control dial and temperature control dial to maintain
maximum comfort.
The Recirculated Air Position:
Using the position in cold or
rainy weather will cause the windows
to fog up. Your vision will be
hampered, which could lead to a
serious accident. Do not use the
position in cold or rainy weather.
NOTE
•If the windshield fogs up easily, set
the mode selector dial to the
position.
• If cooler air is desired at face level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
• The air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
• In the position, air conditioning
is automatically turned on to defrost
the windshield (however, the
indicator light does not illuminate)
and the position is
automatically selected.
WARNING
When using the air conditioner while
driving up long hills or in heavy traffic,
closely monitor the temperature gauge
(page 5-29).
The air conditioner may cause engine
overheating. If the gauge indicates
overheating, turn the air conditioner
off.
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 7 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-8
Interior Comfort
Climate Control System
Form No. 8S18-EA-03I

Ventilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the position.
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.

Windshield Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the desired position.
3. Set the fan control dial to the desired speed.
NOTE
•When maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set
the air intake selector to the
position, then set the fan control dial
to position 4.
• If warmer air is desired at floor
level, set the mode selector dial at
the position and adjust the
temperature control dial to maintain
maximum comfort.
• The air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Foggy Windshield:
Using the position with the
temperature control set to the cold
position will cause the outside of the
windshield to fog up. Your vision will
be hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the position.
NOTE
•For maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
• If warm air is desired at the floor,
set the mode selector dial to the
position.
• In the or position, air
conditioning is automatically turned
on to defrost the windshield quickly
(however, the indicator light does
not illuminate) and the
position is automatically selected.
The air intake selector switch
cannot be changed to the
position.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 8 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-9
Interior Comfort
Climate Control System
Form No. 8S18-EA-03I

Dehumidifying (With Air
Conditioner)
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.
1. Set the mode selector dial to the
desired position.
2. Set the air intake selector to the position.
3. Set the temperature control dial to the desired position.
4. Set the fan control dial to the desired speed.
5. Turn on the air conditioner.
J48C_8S18-EA-03I_Edition3.book Page 9 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

9-16
Customer Information and Reporting Safety Defects
Form No. 8S18-EA-03I
Uniform Tire Quality Grading System (UTQGS)
This information relates to the tire grading system developed by the U.S. National
Highway Traffic Safety Administration for grading tires by tread wear, traction, and
temperature performance.

Tr e a d We a r
The tread wear grade is a comparative rating based on the wear rate of the tire when tested
under controlled conditions on a specified government test course.
For example, a tire graded 150 would wear one-and-a-half times as well on the government
course as a tire graded 100.
The relative performance of tires depends upon the actual conditions of their use, however,
and may depart significantly from the norm because of variations in driving habits, service
practices and differences in road characteristics and climate.

Traction-AA, A, B, C
The traction grades, from highest to lowest, are AA, A, B, and C. These grades represent
the tire
’s ability to stop on wet pavement as measured under controlled conditions on
specified government test surfaces of asphalt and concrete. A tire marked C may have poor
traction performance.

Te m p e r a t u r e - A , B , C
The temperature grades A (the highest), B, and C, represent the tire
’s resistance to the
generation of heat and its ability to dissipate heat when tested under controlled conditions
on a specified indoor laboratory test wheel.
Sustained high temperature can cause the material of the tire to degenerate and reduce tire
life, and excessive temperatures can lead to sudden tire failure.
Grade C corresponds to a level of performance which all passenger vehicle tires must meet
under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent
higher levels of performance on the laboratory test wheel than the minimum required by
law.
Uniform Tire Quality Grading System (UTQGS)
The traction grade assigned to this tire is based on braking (straight ahead) traction
tests and does not include acceleration cornering (turning), hydroplaning, or peak
traction characteristics.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 16 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

11-2
Form No. 8S18-EA-03I
Index
A
Add-On Non-Genuine Parts and
Accessories
...................................... 9-13
Air Bag Systems
.............................. 2-36
Air Filter
.......................................... 8-23
Antenna
............................................ 6-10
Anti-Lock Brake System (ABS)
........ 5-7
Warning light
.............................. 5-8
Appearance Care
.............................. 8-51
Ashtray
............................................. 6-40
Audio System
................................... 6-10
Audio control switch
................ 6-32
Audio set
................................... 6-17
Operating tips for audio
system
....................................... 6-10
Safety certification
.................... 6-34
Automatic Transaxle Driving tips
............................... 5-16
Fluid
.......................................... 8-20
Manual shift mode
.................... 5-13
Shift-lock override
.................... 5-12
Shift-lock system
...................... 5-12
Transaxle ranges
....................... 5-11
B
Battery Emergency starting
................... 7-15
Maintenance
............................. 8-28
Specifications
........................... 10-4
Beep Sounds Ignition key reminder
............... 5-43
Lights-on reminder
................... 5-43
Seat belt warning beep
.............. 5-43
Tire inflation pressure warning
beep
........................................... 5-43
Before Starting the Engine
................. 4-6
After getting in
........................... 4-6
Before getting in
......................... 4-6
B
Body Lubrication ............................. 8-22
Bottle Holder
.................................... 6-42
Brake/Clutch Fluid
.......................................... 8-18
Brakes Anti-lock brake system (ABS)
....5-7
Brakes assist
................................5-8
Foot brake
................................... 5-4
Parking brake
.............................. 5-5
Warning light
.............................. 5-6
Break-In Period
.................................. 4-7
Bulb Replacement
............................ 8-36
C
Capacities ......................................... 10-5
Carbon Monoxide
.............................. 4-5
Cargo Securing Loops
...................... 6-43
Cargo Sub-Compartment
................. 6-44
Catalytic Converter
............................ 4-3
Cell Phones
...................................... 9-14
Center Console
................................. 6-43
Child Restraint Child restraint precautions
........ 2-21
Installing child-restraint
systems
...................................... 2-25
LATCH child-restraint
systems
...................................... 2-32
Child Safety Locks for Rear
Doors
.................................................. 3-9
Cigarette Lighter
.............................. 6-40
Climate Control System
.....................6-2
Gas specifications
..................... 10-6
Clock
................................................ 6-39
Cruise Control
.................................. 5-18
Cup Holder
....................................... 6-41
Customer Assistance
.......................... 9-2
J48C_8S18-EA-03I_Edition3.book Page 2 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI