2004 MAZDA MODEL 3 4-DOOR ignition

6-35
Interior Comfort
Form No. 8S18-EA-03I
Interior Equipment
When you need a sunvisor, lower it for use
in front or swing it to the side.

Va n i t y M i r r o r s
To use the vanity mirror, lower the
sunvisor.

Illuminated Entry System*
When the illuminated entry system
operates, the overhead light (switch is in
the DOOR position) turns on for:
• About 30 seconds after the driver
’s
door is unlocked and the ignition key is
removed.
• About 15 seconds after all doors are
closed.
• About 15 seconds after the key is
removed from the ignition with all
doors closed.
The light also turns off when:
• The ignition switch is turned to the ON
position and all doors are closed.
• The driver
’s door is locked.
Sunvisors
Sunvisor
Interior Lights
NOTE
If any door is left opened, the light
goes out after about 5 minutes.
The light turns on again when the
ignition switch is turned to the ON
position, or when any door is opened
after all doors have been closed.
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 35 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-39
Interior Comfort
Interior Equipment
Form No. 8S18-EA-03I

Clock
When the ignition switch is in the ACC or
ON position, the time is displayed.
Time setting
1. Press the CLOCK button until a beep
sounds, and "12Hr" and "24Hr" will be
displayed.
2. Press the SET button to switch between "12Hr" and "24Hr" displays. The
selected display will flash.
To select the desired clock setting,
press the CLOCK button again while
the preferred setting is flashing.
3. "Hr. ADJUST" will be displayed next, and the hour portion of the display will
flash. Press the SET button to set the
hour, then press the CLOCK button.
4. "Min. ADJUST" will be displayed next, and the minutes portion of the
display will flash. Press the SET button
to set the minutes, then press the
CLOCK button. Time resetting
While the clock is displayed, press the
SET button 1.5 seconds or more. When
the button is released, a beep will sound
and the clock will be reset as follows:
(Example)
12:01—12:29
→12:00
12:30—12:59 →1:00


Audio Display
The audio system status is displayed. To
operate the audio system, refer to "Audio
System" (page 6-10).
NOTE
When the SET button is released, the
seconds are reset to "00".
J48C_8S18-EA-03I_Edition3.book Page 39 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

6-40
Interior Comfort
Interior Equipment
Form No. 8S18-EA-03I
The ignition switch must be in the ACC or
ON position.
Press the lighter in and release it. When
ready for use, it automatically pops out.To use, open the cover.
To remove, open the cover and pull up the
ashtray.
Lighter
•Don
’t touch the metal part of the
lighter, you may burn yourself.
• Don
’t hold the lighter in because it
will overheat.
• Don
’t use the lighter socket for
plug-in accessories such as shavers
and coffee pots. They may damage
it or cause electrical failure. Use
only a genuine Mazda lighter or the
equivalent.
• If the lighter doesn
’t pop out within
30 seconds, remove it to prevent
overheating.
CAUTION
Ashtray
Don ’t use the ashtray for trash. You
might start a fire.
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 40 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

7-13
In Case of an Emergency
Form No. 8S18-EA-03I
Overheating
If the temperature gauge indicates
overheating, the vehicle loses power, or
you hear a loud knocking or pinging
noise, the engine is probably too hot.If the temperature gauge indicates
overheating:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic transaxle in park (P), a manual
transaxle in neutral.
Apply the parking brake.
3. Turn off the air conditioner.
4. Check whether coolant or steam is escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don ’t go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the hood and start the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools.
5. Make sure the cooling fan is operating, then turn off the engine after the
temperature has decreased.
Overheating
Cooling Fan and Engine
Inspection:
Inspecting the engine with the
ignition switch in the ON position is
dangerous. The cooling fan could
turn on unexpectedly even when the
engine isn ’t running. You could be
seriously injured by the fan. Turn the
ignition switch off and remove the key
from the ignition switch when you
inspect the engine.
Cooling System Cap:
When the engine and radiator are
hot, scalding coolant and steam may
shoot out under pressure and cause
serious injury. Don ’t remove the
cooling system cap when the engine
and radiator are hot.
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an Authorized Mazda
Dealer.
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 13 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

7-15
In Case of an Emergency
Form No. 8S18-EA-03I
Emergency Starting
If the engine fails to start, it may be
flooded (excessive fuel in the engine).
Follow this procedure:
1. Depress the accelerator all the way and hold it there.
2. Turn the ignition switch to the START position and hold it there —for up to 10
seconds. If the engine starts, release the
key and accelerator immediately
because the engine will suddenly rev
up.
3. If the engine fails to start, crank it without depressing the accelerator —
for up to 10 seconds.
Starting a Flooded Engine
J48C_8S18-EA-03I_Edition3.book Page 15 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

7-17
In Case of an Emergency
Emergency Starting
Form No. 8S18-EA-03I
Keep Flames Away:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all flames including
cigarettes and sparks away from open battery cells. When working near a battery, do
not allow metal tools to contact the positive ( ) or negative ( ) terminal of the
battery. Do not allow the positive ( ) terminal to contact the vehicle body.Battery-Related Explosion:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all flames, including
cigarettes, and sparks away from open battery cells.
Low Fluid Level or Frozen Battery:
Jump-starting a frozen battery or one with a low fluid level is dangerous. It may
rupture or explode, causing serious injury.
Don’t jump-start a frozen battery or one with a low fluid level.
Connecting to Negative Terminal:
Connecting the end of the second cable to the negative ( ) terminal of the discharged
battery is dangerous.
A spark could cause the gas around the battery to explode and injure someone.
Connect the cable to a point away from the battery.
Connecting Jumper Cable to Moving Parts:
Connecting a jumper cable near or to moving parts (cooling fans, belts) is dangerous.
The cable could get caught when the engine starts and cause serious injury. Never
connect a jumper cable to or near any part that moves.
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and
other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in
series or a 24 V motor generator set).
WARNING
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 17 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
R : Replace
L : Lubricate
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
CHASSIS and BODY
*1:According to state / provincial and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage / kilometer period to ensure long-term reliability.
Maintenance Interval
(Number of months or
kilometers (miles), whichever comes first)Months 6 12182430364248
× 1000 km 12 24 36 48 60 72 84 96
× 1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
Engine valve clearance A u d i b l e i n s p e c t e v e r y 1 2 0 , 0 0 0 k m ( 7 5 , 0 0 0 m i l e s ) ,
if noisy, adjust
Drive belts (tension) I
Engine oil RRRRRRRR
Engine oil filter RRRRRRRR
Cooling system II
Engine coolant Replace at first 96,000 km (60,000 miles) or 4 years ;
after that, every 2 years
Air filter R
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Spark plugs Replace every 120,000km (75,000miles)
Brake lines, hoses and connections II
Disc brakes IIII
Tire (Rotation) Rotate every 12,000km (7,500miles)
Steering operation and linkages II
Front and rear suspension and ball joints II
Driveshaft dust boots II
Exhaust system and heat shields Inspect every 72,000km (45,000miles) or 60 months
All locks and hinges LLLLLLLL
J48C_8S18-EA-03I_Edition3.book Page 4 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
R : Replace
L :Lubricate
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
ELECTRICAL SYSTEM
*1:According to state / provincial and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage / kilometer period to ensure long-term reliability.
Maintenance Interval
(Number of months or kilometers (miles),
whichever comes first)Months 4 8 12 16 20 24 28 32 36 40 44 48
× 1000 km 8 1624324048566472808896
× 1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Engine valve clearance Audible inspect every 120,000km (75,000miles), if noisy, adjust
Drive belts (tension) I
Engine oil Puerto Rico
Replace every 5,000 km (3,000 miles) or 3 months
Others RRRRRRRRRRRR
Engine oil filter RRRRRRRRRRRR
Cooling system II
Engine coolant R e p l a c e a t f i r s t 9 6 , 0 0 0 k m ( 6 0 , 0 0 0 m i l e s ) o r 4 y e a r s ;
after that, every 2 years
Engine coolant level IIIIIIIIIIII
Air filter Puerto Rico
RR
Others R
Fuel lines and hoses
*1II
Hoses and tubes for emission
*1I
Spark plugs Replace every 120,000km (75,000miles)
Function of all lights IIIIIIIIIIII
J48C_8S18-EA-03I_Edition3.book Page 5 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI