2004 MAZDA MODEL 3 4-DOOR door lock

3-23
Knowing Your Mazda
Doors and Locks
Form No. 8S18-EA-03I
The sunshade doesn’t tilt. To avoid
damaging the sunshade, don ’t push up
on it.
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 23 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

3-27
Knowing Your Mazda
Security System
Form No. 8S18-EA-03I
The optional theft-deterrent system is
designed to prevent your vehicle or its
contents from being stolen when all the
doors, hood, and trunk lid/liftgate are
locked.
If forcible entry is attempted, the system
sounds the horn and flashes the hazard
warning lights.

Operation
System triggering conditions
The horn sounds intermittently and the
hazard warning lights flash for about 3
minutes when the system is triggered by
any one of the following:
• Forcing open a door, the hood or the
trunk lid/liftgate.
• Opening a door, the hood or the trunk
lid by operating an inside door-lock
knob, the hood release handle or the
trunk lid release lever.
If the system is triggered again, the lights
and horn will activate until a door or the
trunk lid is unlocked with the key or with
the transmitter.

How to Arm the System
1. Remove the key from the ignition
switch.
2. Close the hood. Then close and lock all doors and the trunk lid/liftgate from the
outside using the key. If you have the
keyless entry system, press the LOCK
button on the transmitter. The hazard
warning lights will flash once to
indicate that the system is armed.
The following method will also arm the
theft-deterrent system:
Close the hood and the trunk lid/
liftgate . Press the area on the door-lock
switch marked "LOCK" once. Close all
doors.
Theft-Deterrent System*
NOTE
•The theft-deterrent system operates
with the key or the keyless entry
system transmitter.
• The system will not function unless
it is properly armed. To properly
secure the vehicle, always make
sure all the windows are completely
closed and all doors and the liftgate
are locked before leaving the
vehicle. Remember to take your key
and transmitter.
NOTE
Locking the doors with the inside
door-lock knob will not arm the
system.
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 27 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

3-28
Knowing Your Mazda
Security System
Form No. 8S18-EA-03I

To Tu r n o f f a n A r m e d S y s t e m
An armed system can be turned off by any
one of the following methods:
• Unlock a door or the trunk lid with the
key.
• Press the UNLOCK button on the
keyless entry system transmitter.
• Insert the key into the ignition switch
and turn it to the ON position.


To Stop an Alarm
A triggered alarm can be turned off by any
one of the following methods:
• Unlock a door or the trunk lid with the
key.
• Press the UNLOCK button on the
keyless entry system transmitter.


Theft-Deterrent Labels
Labels indicating that your vehicle is
equipped with a Theft-Deterrent System
are in the glove box.
Mazda recommends that you affix them to
the lower rear corner of the front door
windows.
NOTE
If you have any problem with the theft-
deterrent system, consult an
Authorized Mazda Dealer.
J48C_8S18-EA-03I_Edition3.book Page 28 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

3-29
Knowing Your Mazda
Form No. 8S18-EA-03I
Steering Wheel and Mirrors

Steering Wheel Adjustment
To change the angle or length of the
steering wheel:
1. Stop the vehicle, pull down the lock
release lever under the steering
column.
2. Tilt the steering wheel and/or adjust the steering column length to the desired
positions, push the lever up to lock the
column.
3. Push the wheel up and down to be certain it ’s locked before driving.

Outside Mirrors
Check the mirrors
’ angles before driving.
Manual control mirror
To adjust, move the mirror ’s control lever,
just inside the door.
Steering Wheel
Adjusting the Steering Wheel:
Adjusting the steering wheel while the
vehicle is moving is dangerous.
Moving it can very easily cause the
driver to abruptly turn to the left or
right. This can lead to loss of control
or an accident. Never adjust the
steering wheel while the vehicle is
moving.
WARNING
Lock release lever
Mirrors
Convex Mirror (Passenger Side):
Changing lanes without taking into
account the actual distance of the
vehicle in the convex mirror is
dangerous. You could have a serious
accident. What you see in the convex
mirror is closer than it appears. Be
sure to look over your shoulder before
changing lanes.
WARNING
Control lever
J48C_8S18-EA-03I_Edition3.book Page 29 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

4-6
Before Driving Your Mazda
Form No. 8S18-EA-03I
Before Starting the Engine
•Be sure the windows, outside mirrors,
and outside lights are clean.
• Inspect inflation pressures and
condition of tires.
• Look under the vehicle for any sign of
a leak.
• If you plan to back up, make sure
nothing will be in your way. •
Are all doors closed and locked?
• Is the seat adjusted properly?
• Are the inside and outside mirrors
adjusted?
• Is everyone’
s seat belt fastened?
• Check all gauges.
• Check all warning lights when the
ignition switch is turned to the ON
position.
• Release the parking brake and make
sure the brake warning light goes off.
Always be thoroughly familiar with your
Mazda.
Before Getting In
NOTE
Engine oil, engine coolant, brake/
clutch fluid, washer fluid, and other
fluid levels should be inspected. See
Maintenance, Section 8.
After Getting In
J48C_8S18-EA-03I_Edition3.book Page 6 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

5-3
Driving Your Mazda
Starting and Driving
Form No. 8S18-EA-03I
ACC (Accessory)
The steering wheel unlocks and some
electrical accessories will operate.
ON
This is the normal running position after
the engine is started. The warning lights
(except brakes) should be inspected
before the engine is started (page 5-31).
START
The engine is started in this position. It
will crank until you release the key; then
it returns to the ON position. The brake
warning light can be checked after the
engine is started (page 5-31).

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep sound will be heard
when the driver
’s door is opened. 1. Occupants should fasten their seat
belts.
2. Make sure the parking brake is on.
3. Depress the brake pedal.
4. (Manual transaxle)

Depress the clutch pedal all the way
and shift into neutral.
Keep the pedal depressed while
cranking the engine.
(Automatic transaxle)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
If turning the key is difficult, jiggle the
steering wheel from side to side.
NOTE
When the ignition switch is turned to
the ON position, the sound of the fuel
pump motor operating near the fuel
tank can be heard. This does not
indicate an abnormality.
Starting the Engine
NOTE
Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of
radio noise.
NOTE
(Manual transaxle)
The starter will not operate if the
clutch pedal is not
pushed down all the
way.
(Automatic transaxle)
The starter will not operate if the shift
lever is not
in P or N.
J48C_8S18-EA-03I_Edition3.book Page 3 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

5-27
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8S18-EA-03I

Speedometer
The speedometer indicates the speed of
the vehicle.

Odometer, Trip Meter and Trip
Meter Selector
The display mode can be changed
between trip meter A and trip meter B by
pressing the selector while one of them is
displayed. The selected mode will be
displayed.
Odometer
The odometer records the total distance
the vehicle has been driven.
Selector
Trip meter
Odometer
Odometer
Odometer Trip meter A
Press the selector
Press the selector
Trip meter B
NOTE
•
(Standard meter)

The odometer and trip meter can be
displayed as follows even when the
ignition switch is in the ACC or
LOCK position.
 Displays for 10 minutes after the
ignition switch is turned to the
ACC or LOCK position from the
ON position.
 Displays for 10 minutes after the
driver’ s door is opened.
• (Black-out meter)

When the ignition switch is in the
ACC or LOCK position, the
odometer or trip meters cannot be
displayed, however, pressing the
selector button can inadvertently
switch the trip meters or reset them
during an approximate ten-minute
period in the following cases:
 After the ignition switch is
turned to the ACC or LOCK
position from the ON position.
 After the driver ’s door is opened.
J48C_8S18-EA-03I_Edition3.book Page 27 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

5-43
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
Form No. 8S18-EA-03I

Seat Belt Warning Beep
If the driver
’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep sound will be heard
for about 6 seconds.
The beep sound will be heard again for
about 6 seconds every 30 seconds, for a
period of about 5 minutes if the driver ’s
seat belt is not fastened afterwards.
Refer to Seat Belt Warning Light/Beep
(page 5-37).

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep sound will be heard
when the driver
’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep sound
will be heard when the driver’
s door is
opened.

Tire Inflation Pressure Warning
Beep*
The warning beep sound will be heard for
about 3 seconds when there is any
abnormality in tire inflation pressures
(page 5-22).
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 43 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI