2004 MAZDA MODEL 3 4-DOOR battery

7-16
In Case of an Emergency
Emergency Starting
Form No. 8S18-EA-03I
Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If you
feel unsure about jump-starting, we strongly recommend that you have a competent service
technician do the work.
Jump-Starting
Follow These Precautions Carefully:
To ensure safe and correct handling of the battery, read the following precautions
carefully before using the battery or inspecting it.Eye Protection:
Working without eye protection is dangerous. Battery fluid contains SULFURIC
ACID which could cause blindness if splashed into in your eyes. Also, hydrogen gas
produced during normal battery operation, could ignite and cause the battery to
explode. Always wear eye protection when working near the battery.Spilled Battery Fluid:
Spilled battery fluid is dangerous.
Battery fluid contains SULFURIC ACID which could cause serious injuries if it gets
in eyes, skin or clothing. If this happens, immediately flush your eyes with water for
15 minutes or wash your skin thoroughly and get medical attention. Wear eye
protection and protective gloves to prevent contact with battery fluid.Children and Batteries:
Allowing children to play near batteries is dangerous. Battery fluid could cause
serious injuries if it gets in the eyes or on the skin. Always keep batteries out of the
reach of children.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 16 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

7-17
In Case of an Emergency
Emergency Starting
Form No. 8S18-EA-03I
Keep Flames Away:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all flames including
cigarettes and sparks away from open battery cells. When working near a battery, do
not allow metal tools to contact the positive ( ) or negative ( ) terminal of the
battery. Do not allow the positive ( ) terminal to contact the vehicle body.Battery-Related Explosion:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all flames, including
cigarettes, and sparks away from open battery cells.
Low Fluid Level or Frozen Battery:
Jump-starting a frozen battery or one with a low fluid level is dangerous. It may
rupture or explode, causing serious injury.
Don’t jump-start a frozen battery or one with a low fluid level.
Connecting to Negative Terminal:
Connecting the end of the second cable to the negative ( ) terminal of the discharged
battery is dangerous.
A spark could cause the gas around the battery to explode and injure someone.
Connect the cable to a point away from the battery.
Connecting Jumper Cable to Moving Parts:
Connecting a jumper cable near or to moving parts (cooling fans, belts) is dangerous.
The cable could get caught when the engine starts and cause serious injury. Never
connect a jumper cable to or near any part that moves.
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and
other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in
series or a 24 V motor generator set).
WARNING
CAUTION
J48C_8S18-EA-03I_Edition3.book Page 17 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

7-18
In Case of an Emergency
Emergency Starting
Form No. 8S18-EA-03I
1. For vehicle equipped with the engine cover, remove the engine cover.
2. Remove the battery cover from its front side. 3. Make sure the booster battery is 12 V
and that its negative terminal is
grounded.
4. If the booster battery is in another vehicle, don ’t allow the vehicles to
touch. Turn off the engine of the
vehicle with the booster battery and all
unnecessary electrical loads in both
vehicles.
5. Connect the jumper cables in the exact sequence as in the illustration.
Connect one end of a cable to the
positive terminal on the discharged
battery (1).
 Attach the other end to the positive
terminal on the booster battery (2).
 Connect one end of the other cable
to the negative terminal of the
booster battery (3).
 Connect the other end to a solid,
stationary, exposed metallic point
(for example, the right hand side
engine mounting bolt) away from
the discharged battery (4).
Connect cables in numerical order and disconnect in reverse order.
Jumper cables Dischargedbattery
Booster battery
Battery cover
J48C_8S18-EA-03I_Edition3.book Page 18 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-1
Form No. 8S18-EA-03I
8Maintenance and Care
How to keep your Mazda in top condition.
Introduction ................................................................................... 8-2
Introduction ............................................................................... 8-2
Scheduled Maintenance ................................................................ 8-3
Scheduled Maintenance (North America) ................................. 8-3
Scheduled Maintenance (Except North America) ..................... 8-7
Owner Maintenance .................................................................... 8-10
Owner Maintenance Schedule ................................................. 8-10
Owner Maintenance Precautions ............................................. 8-11
Engine Compartment Overview .............................................. 8-12
Engine Oil ................................................................................ 8-13
Engine Coolant ........................................................................ 8-15
Brake/Clutch Fluid .................................................................. 8-18
Power Steering Fluid ............................................................... 8-19
Automatic Transaxle Fluid (ATF) ........................................... 8-20
Washer Fluid ............................................................................ 8-21
Body Lubrication ..................................................................... 8-22
Air Filter .................................................................................. 8-23
Wiper Blades ........................................................................... 8-24
Battery ..................................................................................... 8-28
Tires ......................................................................................... 8-31
Light Bulbs .............................................................................. 8-36
Fuses ........................................................................................ 8-46
Appearance Care ......................................................................... 8-51
How to Minimize Environmental Paint Damage ..................... 8-51
Exterior Care ........................................................................... 8-53
Interior Care ............................................................................ 8-57
J48C_8S18-EA-03I_Edition3.book Page 1 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-8
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I
I: Inspect: Inspect and clean, repair, adjust, or replace if necessary.
R : Replace
C : Clean
*1:Also inspect and adjust the power steering and air conditioner drive belts, if installed.
*2: If the vehicle is operated under any of the following conditions, change the engine oil and oil filter more often than recommended intervals.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation.
c) Driving for long period in cold temperatures or driving regularly at short distance only.
*3:If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air filter more often than the recommended intervals.
*4:If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, change the brake fluid annually.
Maintenance
Interval
(Number of months or
kilometers
(miles), whichever comes first)Months 6 121824303642485460667278849096
× 1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
×1000 miles6.25 12.518.752531.2537.543.755056.2562.568.757581.2587.593.75100
Engine valve clearance Audible inspect every 120,000km (75,000miles), if noisy, adjust
Drive belts
*1IIIIIIIIIIIIIIII
Engine oil*2RRRRRRRRRRRRRRRR
Engine oil filter*2RRRRRRRRRRRRRRRR
Cooling system IIIIIIII
Engine coolant Replace every 2 years
Air filter
*3CCRCCRCC
Spark plugs Replace every 120,000km (75,000miles)
Fuel filter RRRR
Fuel lines and hoses IIIIIIII
Evaporative system
(if installed) IIIIIIII
Battery electrolyte level and
specific gravity IIIIIIII
Brake lines, hoses and
connections IIIIIIII
Brake fluid
*4IIIRIIIRIIIRIIIR
Parking brake IIIIIIIIIIIIIIII
Power brake unit
(Brake booster) and hoses IIIIIIII
Disc brakes IIIIIIIIIIIIIIII
J48C_8S18-EA-03I_Edition3.book Page 8 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-12
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Engine Compartment Overview
Engine oil
dipstick
Fuse block
Air filter
Battery
Brake/Clutch fluid
reservoir
Engine oil-filler cap
Engine coolant
reservoir
Windshield washer
fluid reservoir
Power steering
fluid reservoir
Main fuse
Automatic transaxle fluid-level
dipstick (only for automatic transaxle)
J48C_8S18-EA-03I_Edition3.book Page 12 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-23
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
This air filter may be cleaned with
compressed air and reused, or replaced,
depending on its condition. Unless it is
very dirty, simply shake it to remove
foreign particles. Each time you inspect it,
wipe inside the air cleaner housing with a
damp cloth.

Replacing the Air Filter
1. Make sure the ignition switch is turned
off.
2. Remove the battery cover and battery duct. 3. Unfasten the clamps.
4. Lift off the air filter cover and remove
the filter.
5. Wipe inside the air cleaner housing with a damp cloth.
6. Clean or replace the filter.
7. Install in the reverse order of removal.
Replace the filter according to the
Scheduled Maintenance (page 8-3).
Air Filter
Don ’t drive without an air filter. This
could result in excessive engine wear.
NOTE
If the vehicle is operated in very dusty
or sandy areas, replace the filter more
often than the recommended intervals.
Use a Mazda genuine air filter. Use of
other filters could damage the airflow
sensor.
CAUTION
CAUTION
Battery duct
Battery cover
Clamp
Air filter cover
Air filter
J48C_8S18-EA-03I_Edition3.book Page 23 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-28
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Battery
Battery-Related Lead Materials:
Battery posts, terminals and related accessories contain lead and lead compounds,
chemicals known to the State of California to cause cancer and reproductive harm.
Wash hands after handling.Follow These Precautions Carefully:
To ensure safe and correct handling of the battery, read the following precautions
carefully before using the battery or inspecting it.Eye Protection:
Working without eye protection is dangerous. Battery fluid contains SULFURIC
ACID which could cause blindness if splashed into in your eyes. Also, hydrogen gas
produced during normal battery operation, could ignite and cause the battery to
explode. Always wear eye protection when working near the battery.Spilled Battery Fluid:
Spilled battery fluid is dangerous.
Battery fluid contains SULFURIC ACID which could cause serious injuries if it gets
in eyes, skin or clothing. If this happens, immediately flush your eyes with water for
15 minutes or wash your skin thoroughly and get medical attention. Wear eye
protection and protective gloves to prevent contact with battery fluid.Children and Batteries:
Allowing children to play near batteries is dangerous. Battery fluid could cause
serious injuries if it gets in the eyes or on the skin. Always keep batteries out of the
reach of children.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 28 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI