2004 MAZDA MODEL 3 4-DOOR engine

8-22
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.
To inspect the washer fluid level in the
front reservoir, pull off the cap. Then,
holding your thumb over the hole in the
center of the cap, lift it straight up. The
fluid level can be seen from the fluid
column in the pipe. Add fluid if necessary.
Use plain water if washer fluid is
unavailable. But use only washer fluid in
cold weather to prevent it from freezing.All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the hood
’s secondary latch
keeps the hood from opening when the
primary latch is released.
NOTE
Front and rear washer fluid is supplied
from the same reservoir.
Body Lubrication
J48C_8S18-EA-03I_Edition3.book Page 22 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-23
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
This air filter may be cleaned with
compressed air and reused, or replaced,
depending on its condition. Unless it is
very dirty, simply shake it to remove
foreign particles. Each time you inspect it,
wipe inside the air cleaner housing with a
damp cloth.

Replacing the Air Filter
1. Make sure the ignition switch is turned
off.
2. Remove the battery cover and battery duct. 3. Unfasten the clamps.
4. Lift off the air filter cover and remove
the filter.
5. Wipe inside the air cleaner housing with a damp cloth.
6. Clean or replace the filter.
7. Install in the reverse order of removal.
Replace the filter according to the
Scheduled Maintenance (page 8-3).
Air Filter
Don ’t drive without an air filter. This
could result in excessive engine wear.
NOTE
If the vehicle is operated in very dusty
or sandy areas, replace the filter more
often than the recommended intervals.
Use a Mazda genuine air filter. Use of
other filters could damage the airflow
sensor.
CAUTION
CAUTION
Battery duct
Battery cover
Clamp
Air filter cover
Air filter
J48C_8S18-EA-03I_Edition3.book Page 23 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-46
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Yo u r v e h i c l e’s electrical system is
protected by fuses.
If any lights, accessories, or controls don ’t
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.

Fuse Replacement
Replacing the fuses on the front
passenger
’s side below the glove box
If the electrical system doesn ’t work, first
inspect fuses on the front passenger ’s side
below the glove box.
1. Turn off the ignition switch and other switches.
2. Remove the cover. 3. Turn the knobs counterclockwise and
lower the fuse block.
4. Locate the position of the suspected fuse by using the chart inside the fuse
block cover.
5. Pull the fuse straight out with the fuse puller provided on the inside of the
engine compartment fuse block cover.
Fuses
Cover
Fuse block cover
Fuse puller
J48C_8S18-EA-03I_Edition3.book Page 46 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-48
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Fuse Panel Description
Fuse block (Engine compartment)
12 3
4 5 6
789
10
11 12 13
1415
16 17 18
19 20 21
22
23
24
25
26
27
28
29
30 31
32
33
34
35
36
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 FAN 40A Cooling fan
2 P/ST 80A EHPAS
3BTN 40A For protection of
various circuits
4HEAD 40AHeadlights
5PTC 80A —
6GLOW 60A —
7ABS 1 30A ABS
*
8ABS 2 20AABS*
9 ENGINE 30AFor protection of
various circuits
10 —— —
11 IG KEY 1 30A Ignition switch
12 STARTER 20A Starter clutch
13 IG KEY 2 30A Ignition switch
14 —— —
15 HEATER 40A Blower motor
16 —— —
17 DEFOG 40A Rear window
defroster
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
18 —— —
19 ABS IG 10A ABS
*
20 FOG 15AFog lights*
21 HORN 15A Horn
22—— —
23 H/CLEAN 20A —
24 F/PUMP 15A Fuel pump
25 P/ST IG 10A Power steering
26 A/C MAG 10A Air conditioner
27 ALT 10A —
28 —— —
29 —— —
30 ENG +B 10A PCM
31 ROOM 15A Interior lights
32
ENG BAR 410A O2 heater
33
ENG BAR 310A O2 heater
34 EGI INJ 10A Injector
35
ENG BAR 110A Air flow sensor
36ENG BAR 210A EGR control valve
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 48 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-50
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
66 METER 10A Instrument cluster,
Immobilizer
system, Shift lock
system
67 IGNITION 20A ABS
*, EHPAS*
68 WIPER 20A Windshield wiper
69 ENGINE 20AFor protection of
various circuits
70 IG SIG 10A Auto wiper
*
71 SAS 2 7.5ASupplemental
restraint system
72 —— —
73 —— —
74 SEAT
WA R M 20A
—
75 D/LOCK 1 25A Power door lock
76 A/C 10A Air conditioner,
Heater control unit
77 P/WIND L 30A Power window
(LH)
*
78 P/WIND R 30APower window
(RH)*
79 BACK 10A Reverse lights
80
SUN
RO O F 7.5A
Moonroof
*
81 TAIL L 7.5A Taillights (LH),
Parking lights (LH)
82 ILLUMI 7.5A Illumination
83 —— —
84 —— —
85 —— —
86 —— —
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 50 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

9-10
Customer Information and Reporting Safety Defects
Wa r r a n t y
Form No. 8S18-EA-03I
Government regulations in the United States require that automobiles meet specific
emission regulations and safety standards. Therefore, vehicles built for use in the United
States may differ from those sold in other countries.
The differences may make it difficult or even impossible for your vehicle to receive
satisfactory servicing in other countries. We strongly recommend that you NOT take your
Mazda outside the United States. However, in the event that you are moving to Canada
permanently, Mazda vehicles built for use in the United States could be eligible for
exportation to Canada with specific vehicle modifications to comply with the Canadian
Motor Vehicle Safety requirements (CMVSS).
You may have the following problems if you do take your vehicle outside of the United
States:
•Recommended fuel may be unavailable. Any kind of leaded fuel or low-octane fuel will
affect vehicle performance and damage the emission controls and engine.
• Proper repair facilities, tools, testing equipment, and replacement parts may not be
available.
Please refer to your Manufacturer’ s Warranty Booklet for more information.
Outside the United States
NOTE
The above is applicable for a permanent import/export situation and not related to
travelers on vacation.
J48C_8S18-EA-03I_Edition3.book Page 10 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

9-11
Customer Information and Reporting Safety Defects
Wa r r a n t y
Form No. 8S18-EA-03I
Government regulations in Canada require that automobiles meet specific emission
regulations and safety regulations. Therefore, vehicles built for use in Canada may differ
from those sold in other countries.
The differences may make it difficult or even impossible for your vehicle to receive
satisfactory servicing in other countries. We strongly recommend that you NOT take your
Mazda outside Canada. However, in the event that you are moving to the United States
permanently, Mazda vehicles built for use in Canada could be eligible for exportation to the
United States with specific vehicle modifications to comply with the United States Federal
Motor Vehicle Safety Standards (FMVSS).
You may have the following problems if you do take your vehicle outside of Canada:
•Recommended fuel may be unavailable. Any kind of leaded fuel or low-octane fuel will
affect vehicle performance and damage the emission controls and engine.
• Proper repair facilities, tools, testing equipment, and replacement parts may not be
available.
Please refer to your Manufacturer’ s Warranty Booklet for more information.
Outside Canada
NOTE
The above is applicable for a permanent import/export situation and not related to
travelers on vacation.
J48C_8S18-EA-03I_Edition3.book Page 11 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

9-13
Customer Information and Reporting Safety Defects
Wa r r a n t y
Form No. 8S18-EA-03I
Non-genuine parts and accessories for Mazda vehicles can be found in stores.
These may fit your vehicle, but they are not approved by Mazda for use with Mazda
vehicles. When you install non-genuine parts or accessories, they could affect your
vehicle’s performance or safety system; the Mazda warranty doesn ’t cover this. Before you
install any non-genuine parts or accessories, consult an Authorized Mazda Dealer.
Mazda assumes no responsibility for death, injury, or expenses that may result from the
installation of add-on non-genuine parts or accessories.
Add-On Non-Genuine Parts and Accessories
Installation of Non-Genuine Parts or Accessories:
Installation of non-genuine parts or accessories is dangerous. Improperly designed
parts or accessories could seriously affect your vehicle ’s performance or safety system.
This could cause you to have an accident or increase your chances of injuries in an
accident. Always consult an Authorized Mazda Dealer before you install non-genuine
parts or accessories.
Add-On Electrical and Electronic Equipment:
Incorrectly choosing or installing improper add-on equipment or choosing an
improper installer is dangerous. Essential systems could be damaged, causing engine
stalling, air-bag (SRS) activation, ABS inactivation, or a fire in the vehicle.
Be very careful in choosing and installing add-on electrical equipment, such as
mobile telephones, two-way radios, stereo systems, and car alarm systems.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 13 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI