2004 Lexus ES330 inflation pressure

CHASSIS
390
Inspection and adjustment procedure

1Tire valve
2Tire pressure gauge
1. Remove the tire valve cap.
2. Press the tip of the tire pressure gauge to the tire
valve.
3. Read the pressure using a graduation of the gauge.
4. In case that the tire inflation pressure is not within
the prescribed range, insert the compressed air from
the valve. In case of applying too much air, press
the center of the valve and release the air to adjust.
5. After completing the tire inflation pressure
measurement and adjustment, apply soap water to
the valve and check the leakage.
6. Install the tire valve cap.If the gauge and the air pump are not available, have
your vehicle checked by your Lexus dealer.
CAUTION
Be sure to reinstall the tire valve caps. Without
the valve caps, dirt or moisture could get into
the valve core and cause air leakage. If the caps
have been lost, have new ones put on as soon
as possible.
Incorrect tire inflation pressure may waste fuel, reduce
the comfort of driving, reduce tire life and make your
vehicle less safe to drive.
If a tire frequently needs refilling, have it checked by
your Lexus dealer.

CHASSIS
391
CAUTION
Keep your tires properly inflated. Otherwise, the
following conditions may occur and cause an
accident resulting in death or serious injuries.
Low tire pressure (underinflation) Ð
Excessive wear
Uneven wear
Poor handling
Possibility of blowouts from overheated tire
Poor sealing of the tire bead
Wheel deformation and/or tire separation
A greater possibility of tire damage from road
hazards
High tire pressure (overinflation) Ð
Poor handling
Excessive wear
Uneven wear
A greater possibility of tire damage from road
hazards

CHASSIS
393
1Summer tire or all season tire: An all season
tire has M+Sº on the sidewall. The tire not
marked with M+Sº is a summer tire. For details,
see Types of tiresº on page 400.
2Tire size: For details, see Tire sizeº on page
394.
3DOT and Tire Identification Number (TIN): For
details, see DOT and Tire Identification Number
(TIN)º on page 394.
4Uniform tire quality grading: For details, see
Uniform tire quality gradingº that follows.
5Location of the tread wear indicators: For
details, see Checking and replacing tiresº on
page 402.
6Tire ply composition and materials: Plies mean
a layer of rubber-coated parallel cords. Cords
mean the strands forming the plies in the tire.
7Radial tires or bias-ply tires: A radial tire has
RADIALº on the sidewall. The tire not marked
with RADIALº is a bias-ply tire.
8TUBELESSº or TUBE TYPEº: A tubeless tire
does not have a tube inside the tire. A tube type
tire has a tube inside the tire and the tube
maintains the air pressure.
9Load limit at maximum cold tire inflation
pressure: For details, see Checking and
replacing tiresº on page 402.
10Maximum cold tire inflation pressure: This
means the pressure to which a tire may be
inflated. For details about recommended cold tire
inflation pressure, see Specificationsº on page
384.

CHASSIS
397
Tire related terms
Cold tire inflation
pressureTire inflation pressure when the vehicle has been parked at least 3 hours or
more, or it has not been driven more than 1.5 km or 1 mile under that condition
Maximum inflation
pressureThe maximum cold inflation pressure to which a tire may be inflated and shown
on the sidewall of the tire
Recommended
inflation pressureCold tire inflation pressure recommended by a manufacturer
Accessory weightThe combined weight (in excess of those standard items which may be replaced)
of automatic transmission, power steering, power brakes, power windows, power
seats, radio, and heater, to the extent that these items are available as
factory-installed equipment (whether installed or not)
Curb weightThe weight of a motor vehicle with standard equipment including the maximum
capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and
additional weight optional engine
Maximum loaded
vehicle weightThe sum of Ð
(a) Curb weight;
(b) Accessory weight;
(c) Vehicle capacity weight; and
(d) Production options weight
Normal occupant
weight68 kg (150 lb.) times the number of occupants specified in the second column of
Table 1 that follows

CHASSIS
401
ROTATING TIRES
To equalize tire wear and help extend tire life,
Lexus recommends that you rotate your tires
according to the maintenance schedule. (For
scheduled maintenance information, please refer
to the Owner's Manual Supplement/Scheduled
Maintenanceº.) However, the most appropriate
timing for tire rotation may vary according to your
driving habits and road surface conditions.
The wheel assemblies must be rotated as illustrated
above.
When rotating tires, check for uneven wear and
damage. Abnormal wear is usually caused by
incorrect tire inflation pressure, improper wheel
alignment, out-of balance wheels, or severe braking.Before storing radial, snow or studded tires, mark the
direction of rotation and be sure to install them in the
same direction when using them again. Tires should
be stored in a cool dry place.

CHASSIS
403
Tire selection
When replacing a tire, use a tire of the same size
and construction, and the same or greater
maximum loads as the originally installed tires.
Using any other size or type of tire may seriously
affect handling, ride, speedometer/odometer
calibration, ground clearance, and clearance between
the body and tires or snow chains.
Check that the maximum load of the replaced tire is
greater than 1/2 of the Gross Axle Weight Ratings
(GAWR) of either the front axle or the rear axle,
whichever greater. As for the maximum load of the
tire, see the load limit at maximum cold tire inflation
pressure mentioned on the sidewall of the tire, and
as for the Gross Axle Weight Ratings (GAWR), see
the Certification Label. For details about Certification
Label and sidewall of the tire, see pages 352 and 392.CAUTION
Observe the following instructions. Otherwise,
an accident may occur resulting in death or
serious injuries.
Do not mix radial, bias belted, or bias-ply tires
on your vehicle, as this may cause dangerous
handling characteristics resulting in loss of
control.
Do not use tires other than the manufacturer's
recommended size, as this may cause
dangerous handling characteristics resulting
in loss of control.

GAS STATION INFORMATION

Fuel selection:
Select unleaded gasoline with an Octane Rating of 87
(Research Octane Number 91) or higher. For improved
vehicle performance, the use of premium unleaded
gasoline with an Octane Rating of 91 (Research Octane
Number 96) or higher is recommended.

Fuel tank capacity:
70 L (18.5 gal., 15.4 lmp. gal.)

Engine oil:
Toyota Genuine Motor Oilº or equivalent
Oil grade: API grade SL Energy- Conservingº or ILSAC
multigrade engine oil
Recommended oil viscosity: SAE 5W-30
Oil capacity: L (qt., lmp. qt.)
Drain and refill
With filter 4.7 (5.0, 4.1)
Without filter 4.5 (4.8, 4.0)
See page 370 for detailed information.
Engine coolant:
Capacity: 9.2 L (9.7 qt., 8.2 lmp. qt.)
Coolant type Ð Toyota Super Long Life Coolantº or similar
high quality ethylene glycol based non-silicate, non-amine,
non- nitrite, and non- borate coolant with long- life hybrid
organic acid technology
Do not use plain water alone.
For checking the engine coolant, see page 375.

Automatic transaxle:
Fluid type Ð Toyota Genuine ATF Type T-IV
See page 381 for detailed information.

Tire information:
See pages 389 through 407 for detailed information.

Tire inflation pressure:
Tire size: P215/60R16 94V
Tire inflation pressure:
Front 200 kPa (2.0 kgf/cm
2 or bar, 29 psi)
Rear 200 kPa (2.0 kgf/cm2 or bar, 29 psi)
For sustained high speeds above 160 km/h (99 mph), in
countries where such speeds are permitted by law, add 40
kPa (0.4 kgf/cm
2 or bar, 6 psi) to the front tires and rear tires,
but never exceed the maximum cold tire inflation pressure
molded on the tire sidewall.