2004 JEEP GRAND CHEROKEE tow

Tape Player Operation
Insert the cassette with the exposed tape side toward the
right and the mechanical action of the player will gently
pull the cassette into the play position.
NOTE:When subjected to extremely cold temperatures,
the tape mechanism may require a few minutes to warm
up for proper operation. Sometimes poor playback may
be experienced due to a defective cassette tape. Clean and
demagnetize the tape heads at least twice a year.
Tape Side йD/PTY
Pressing the¹Dbutton during tape mode will cause the
other side of the tape to be played. The display will
confirm the selected tape play direction. The time is
always displayed.
Tape
Press the TAPE button to select the Tape mode.
Seek
Press the SEEK button up for the next selection on the
tape and down to return to the beginning of the current
selection.
Press the SEEK button up or down to move the track
number to skip forward or backward 1 to 7 selections.
Press the SEEK button once to move 1 selection, twice to
move 2 selections, etc. the display will show the total
number of times the SEEK button was pushed. The SEEK
function will be cancelled by pressing either the FF/RW
or AM/FM button.
Fast Forward Ð FF
Press the FF button up momentarily to advance the tape
in the direction that it is playing. The tape will advance
until the button is pressed again or the end of the tape is
reached. At the end of the tape, the tape will play in the
opposite direction.
UNDERSTANDING YOUR INSTRUMENT PANEL 147
4

off until the engine warms up. However, the fan will
engage immediately if the defrost mode is selected or if
you select a fixed blower speed.
Window Fogging
Vehicle windows tend to fog on the inside in mild rainy
or humid weather. To clear the windows, use the A/C,
panel, and blower controls. Direct the panel outlets
toward the side windows. Recirculate without A/C
should not be used for long periods as fogging may
occur. Interior fogging on the windshield can be quickly
removed by using the defrost mode.
REAR WINDOW FEATURES
Rear Window Wiper/Washer
A switch on the right side of the steering column controls
operation of the rear wiper/washer function. Rotating
the center of the switch up to the DEL (Delay) position or
the ON position will activate the wiper. Push the lever
forward to initiate the wash function in any of the threepositions. The wash pump will continue to operate as
long as the button is pressed. Upon release, the wipers
will cycle three times before returning to the set position.
If the rear wiper is operating when the ignition is turned
OFF, the wiper will automatically return to the ªParkº
position.
170 UNDERSTANDING YOUR INSTRUMENT PANEL

NTire Spinning........................214
NTread Wear Indicators..................215
NReplacement Tires.....................215
NAlignment And Balance.................217
mTire Pressure Monitor System Ð If Equipped . . . 217
NTire Pressure Monitor System Tire/Wheel
Rotation And Sensor Replacement Ð If
Equipped...........................218
NGeneral Information...................219
mTire Chains...........................220
mTire Rotation Recommendations............220
mFuel Requirements......................221
NReformulated Gasoline.................222
NGasoline/Oxygenate Blends..............222NMMT In Gasoline.....................223
NSulfur In Gasoline.....................223
NMaterials Added To Fuel................224
mFuel Tank Filler Cap (Gas Cap).............224
mTrailer Towing.........................226
NTrailer And Tongue Weight..............228
NCooling System TipsÐTrailer Towing.......229
NMinimum Vehicle Requirements For Trailer
Towing............................230
mRecreational Towing (Behind Motorhome, Etc.) . . 231
NShifting Into Neutral (N)................232
NShifting Out Of Neutral (N)..............233
mSnow Plow...........................234
STARTING AND OPERATING 175
5

²Vehicle speed is above approximately 30 mph (48
km/h).
²Transmission has reached normal operating tempera-
ture.
When frequent transmission shifting occurs while using
overdrive, such as when operating the vehicle under
heavy load conditions (for example, in hilly terrain,
strong head winds, or trailer towing), turning off over-
drive will improve performance and extend transmission
life by reducing excessive shifting and heat buildup.
4th and 5th gears (Overdrive) can be locked out by
pressing the O/D OFF switch located on side of the
gearshift lever. The O/D OFF indicator light will illumi-
nate to show that the switch has been activated. When
the light is on, 4th and 5th gears (Overdrive) are locked
out. Pressing the switch a second time restores the
Overdrive function. The lockout feature is useful when
towing a trailer or carrying a heavy load.The O/D OFF feature must be selected, if desired, each
time the engine is started.
NOTE:If the vehicle is started in cold outside tempera-
tures, shifts into Overdrive may be delayed (4.7L engines
only). Normal Overdrive and shifting operation will
resume when the temperature of the transmission
STARTING AND OPERATING 183
5

N (Neutral)
Neutral Ð Disengages both the front and rear driveshafts
from the powertrain. To be used for flat towing behind
another vehicle. Refer to ªRecreational Towingº in Sec-
tion 5 of this manual.
4LO
Part Time Four Wheel Drive Low Range Ð Low speed 4
wheel drive. Locks the transfer case inter-axle differen-
tial. Forces the front and rear wheels to rotate at the same
speed. Additional traction and maximum pulling power
for loose, slippery road surfaces only. Do not exceed 25
mph (40 km/h).
Shifting Procedure
2WD to 4 PART TIME or 4 PART TIME to 2WD
Shifting between 2WD and 4 PART TIME can be made
with the vehicle stopped or in motion. If the vehicle is in
motion, shifts can be made up to 55 mph (88 km/h). With
the vehicle in motion, two momentary releases of the
accelerator pedal may be required after shifting. This will
STARTING AND OPERATING 189
5

WARNING!
You or others could be injured if you leave the
vehicle unattended with the transfer case in the N
(Neutral) position without first fully engaging the
parking brake. The transfer case N (Neutral) position
disengages both the front and rear driveshafts from
the powertrain and will allow the vehicle to move
regardless of the transmission position. The parking
brake should always be applied when the driver is
not in the vehicle.
Shift Positions
For additional information on the appropriate use of each
transfer case mode position, see the information below:
4 ALL TIME
Normal All Wheel Drive High Range Ð All roads sur-
faces such as ice, snow, gravel, sand, and dry hard
pavement.
N (Neutral)
Neutral Ð Disengages both the front and rear driveshafts
from the powertrain. To be used for flat towing behind
another vehicle. Refer to ªRecreational Towingº in Sec-
tion 5 of this manual.
4LO
Four Wheel Drive Low Range Ð Low speed 4 wheel
drive. Locks the front and rear driveshafts together.
Forces the front and rear wheels to rotate at the same
192 STARTING AND OPERATING

Loading
The vehicle maximum load on the tire must not exceed
the load carrying capacity of the tire on your vehicle. You
will not exceed the tire's load carrying capacity if you
adhere to the loading conditions, tire size and cold tire
inflation pressures specified on the Tire and Loading
Information placard and the Vehicle Loading section of
this manual.
NOTE:Under a maximum loaded vehicle condition,
gross axle weight ratings (GAWR's) for the front and rear
axles must not be exceeded. For further information on
GAWR's, vehicle loading and trailer towing, see the
Vehicle Loading section of this manual.To determine the maximum loading conditions of your
vehicle, locate the statement ªThe combined weight of
occupants and cargo should never exceed XXX kg or XXX
lbs.º on the Tire and Loading Information placard. The
combined weight of occupants, cargo/luggage and
trailer tongue weight (if applicable) should never exceed
the weight referenced here.
Steps for Determining Correct Load Limit
1. Locate the statement ªThe combined weight of occu-
pants and cargo should never exceed XXX poundsº on
your vehicle's placard.
2. Determine the combined weight of the driver and
passengers that will be riding in your vehicle.
208 STARTING AND OPERATING

3. Subtract the combined weight of the driver and pas-
sengers from XXX kilograms or XXX pounds.
4. The resulting figure equals the available amount of
cargo and luggage load capacity. For example, if ªXXXº
amount equals 1400 lbs. and there will be five 150 lb.
passengers in your vehicle, the amount of available cargo
and luggage load capacity is 650 lb. (1400±750 (5 x 150) =
650 lb.)
5. Determine the combined weight of luggage and cargo
being loaded on the vehicle. That weight may not safely
exceed the available cargo and luggage load capacity
calculated in step 4.6. If your vehicle will be towing a trailer, load from your
trailer will be transferred to your vehicle. Consult this
manual to determine how this reduces the available
cargo and luggage load capacity of your vehicle.
NOTE:The following table shows examples on how to
calculate total load, cargo/luggage and towing capacities
of your vehicle with varying seating configurations and
number and size of occupants. This table is for illustra-
tion purposes only and may not be accurate for the
seating and load carry capacity of your vehicle.
NOTE:For the following example the combined weight
of occupants and cargo should never exceed 865 lbs. (392
Kg).
STARTING AND OPERATING 209
5