2004 JEEP GRAND CHEROKEE radio

Programming HomeLink
NOTE:It is recommended that a new battery be placed
in the hand-held transmitter of the device being pro-
grammed to HomeLink for quicker training and accurate
transmission of the radio frequency signal.
WARNING!
Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run the vehicle's engine while
programming HomeLink. Exhaust gas can cause se-
rious injury or death.
WARNING!
Your motorized door or gate will open and close
while you are programming HomeLink. Do not
program HomeLink if people or pets are in the path
of the door or gate. A moving door or gate can cause
serious injury or death to people and pets or damage
to objects.
1. Position the end of your hand-held transmitter 1-3
inches (5-14 cm) away from the lower left corner of the
EVIC display while keeping the display in view.
NOTE:Some gate operators and garage door openers
may require you to replace the next step with procedures
noted in the9Gate Operator/Canadian Programming9
section.
2. Simultaneously press and hold both the desired
HomeLink button and the hand-held transmitter button.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Gate Operator/Canadian Programming
Canadian radio-frequency laws require transmitter sig-
nals to9time-out9(or quit) after several seconds of
transmission - which may not be long enough for
HomeLink to pick up the signal during programming.
Similar to this Canadian law, some U.S. gate operators are
designed to9time-out9in the same manner.
If you live in Canada or you are having difficulties
programming a gate operator by using the9Program-
ming HomeLink9procedures (regardless of where you
live), replace step two with the following:
NOTE:If programming a garage door opener or gate
operator, it is advised to unplug the device during the
9cycling9process to prevent possible overheating.
Press and hold the HomeLink button while you press
and release - every two seconds ((cycle() your hand-heldtransmitter button until the radio signal has success-
fully been accepted by HomeLink. (The message
TRAINED will appear on the HomeLink display.)
Proceed with the remaining steps under9Programming
HomeLink9to complete.
Using HomeLink
To operate, simply press and release the programmed
HomeLink button. Activation will now occur for the
trained device (i.e. garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc.). For convenience, the hand-held transmitter of the
device may also be used at any time. In the event that
there are still programming difficulties or questions,
contact HomeLink at:www.homelink.comor1-800-355-
3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
3

UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
mInstrument Panel And Interior Controls.......126
mInstrument Cluster......................127
NInstrument Cluster Ð If Equipped.........128
mInstrument Cluster Description.............129
mElectronic Digital Clock..................135
NClock Setting Procedure.................135
mRadio General Information................135
NRadio Broadcast Signals.................135
NTwo Types Of Signals..................135NElectrical Disturbances..................136
NAM Reception.......................136
NFM Reception........................136
mSales Code RBKÐAM/ FM Stereo Radio With
CD Player And CD Changer Controls........136
NRadio Operation......................136
NCD Player Operation...................139
NCD Changer Control Capability Ð If
Equipped...........................140
NRadio Display Messages................1424

mSales Code RBPÐAM & FM Stereo Radio With
Cassette Tape Player, CD Player, And Optional
CD/DVD Changer Controls...............143
NRadio Operation......................143
NTape Player Operation..................147
NCD Player Operation...................149
NCD/DVD Changer Operation Ð If
Equipped...........................150
mSales Code RB1ÐAM/FM Stereo Radio With
DVD/GPS Navigation System..............152
mSatellite Radio Ð If Equipped..............152
NSystem Activation.....................152
NElectronic Serial Number/Sirius Identification
Number (ENS/SID)....................153NSelecting Satellite Mode In RBB And RBK
Radios.............................153
NSelecting Satellite Mode In RBP, RBU, RAZ,
And RBQ Radios.....................154
NSelecting a Channel....................154
NStoring And Selecting Pre-Set Channels......155
NUsing The PTY (Program Type) Button
(If Equipped)........................155
NPTY Button9Scan9.....................155
NPTY Button9Seek9.....................155
NSatellite Antenna......................155
NReception Quality.....................156
m10±Disc Remote CD Changer..............156
NLoading The CD Changer...............156
124 UNDERSTANDING YOUR INSTRUMENT PANEL

mRemote Sound System Controls Ð If Equipped . . 160
NRadio Operation......................161
NTape Player.........................161
NCD Player Ð Single Disc In Radio.........162
NCD Player Ð 10 Disc In Cargo Area........162
mCassette Tape And Player Maintenance.......162
mCD/DVD Disc Maintenance...............163
mRadio Operation And Cellular Phones........164
mClimate Controls.......................164
NAir Conditioning.....................164NBlower Control.......................165
NTemperature Control...................165
NMode Selection.......................166
NInfrared Dual-Zone Climate Control Ð If
Equipped...........................167
NWindow Fogging.....................170
mRear Window Features...................170
NRear Window Wiper/Washer.............170
NRear Window Defroster.................171
UNDERSTANDING YOUR INSTRUMENT PANEL 125
4

ELECTRONIC DIGITAL CLOCK
The clock and radio each use the display panel built into
the radio. A digital readout shows the time in hours and
minutes whenever the ignition switch is in the ON or
ACC position and the time button is pressed.
When the ignition switch is in the OFF position, or when
the radio frequency is being displayed, time keeping is
accurately maintained.
Clock Setting Procedure
1. Turn the ignition switch to the ON or ACC position
and press the time button. Using the tip of a ballpoint pen
or similar object, press either the hour (H) or minute (M)
buttons on the radio.
2. Press the H button to set hours or the M button to set
minutes. The time setting will increase each time you
press a button.
RADIO GENERAL INFORMATION
Radio Broadcast Signals
Your new radio will provide excellent reception under
most operating conditions. Like any system, however, car
radios have performance limitations, due to mobile op-
eration and natural phenomena, which might lead you to
believe your sound system is malfunctioning. To help
you understand and save you concern about these ªap-
parentº malfunctions, you must understand a point or
two about the transmission and reception of radio sig-
nals.
Two Types of Signals
There are two basic types of radio signals... AM or
Amplitude Modulation, in which the transmitted sound
causes the amplitude, or height, of the radio waves to
vary... and FM or Frequency Modulation, in which the
frequency of the wave is varied to carry the sound.
UNDERSTANDING YOUR INSTRUMENT PANEL 135
4

Electrical Disturbances
Radio waves may pick up electrical disturbances during
transmission. They mainly affect the wave amplitude,
and thus remain a part of the AM reception. They
interfere very little with the frequency variations that
carry the FM signal.
AM Reception
AM sound is based on wave amplitude, so AM reception
can be disrupted by such things as lightning, power lines
and neon signs.
FM Reception
Because FM transmission is based on frequency varia-
tions, interference that consists of amplitude variations
can be filtered out, leaving the reception relatively clear,
which is the major feature of FM radio.
SALES CODE RBKÐAM/ FM STEREO RADIO
WITH CD PLAYER AND CD CHANGER CONTROLS
Radio Operation
Power/Volume Control
Press the ON/VOL control to turn the radio on. Turn the
volume control clockwise to increase the volume.
136 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE:Power to operate the radio is supplied through
the ignition switch. It must be in the ON or ACC position
to operate the radio.
Seek
Press and release the SEEK button to search for the next
station in either the AM or FM mode. Press the top of the
button to seek up and the bottom to seek down. The
radio will remain tuned to the new station until you
make another selection. Holding the button in will by-
pass stations without stopping until you release it.
Tune
Press the TUNE control up or down to increase or
decrease the frequency. If you press and hold the button,
the radio will continue to tune until you release the
button. The frequency will be displayed and continu-
ously updated while the button is pressed.
Balance
The Balance control adjusts the left-to-right speaker bal-
ance. Press the BAL button in and it will pop out. Adjust
the balance and push the button back in.
Fade
The Fade control provides for balance between the front
and rear speakers. Press the FADE button in and it will
pop out. Adjust the balance and push the button back in.
Bass and Treble Tone Control
The tone controls consist of 2 separate bands. The bass
band is on the left, and the treble band is on the right.
Each band is adjusted by a slider control with a detent at
the mid-position. Moving the control up or down in-
creases or decreases amplification of that band. The mid
position provides a balanced output.
UNDERSTANDING YOUR INSTRUMENT PANEL 137
4