2004 JEEP GRAND CHEROKEE pressure

8. Return magnet to storage location.
If the display reads TRAINING COMPLETE, pressing
either the STEP, C/T, RESET, or MENU buttons will exit
the training mode.
If the display reads TRAINING ABORTED, move the
vehicle ahead at least 1 foot and complete steps 1±8
again.
For further assistance, questions, or comments about the
Tire Pressure Monitor system, please call1±877±774±
8473.Compass/Temperature/Trip Computer
This display provides the outside temperature, one of the
eight compass headings to indicate the direction the
vehicle is facing, and vehicle trip information. The com-
pass and temperature display is the normal display.
When the C/T button is pressed the compass/
temperature display returns.
WARNING!
Even if the display still reads a few degrees above
32ÉF ( 0ÉC), the road surface may be icy, particularly
in woods or on bridges. Drive carefully under such
conditions to prevent an accident and possible per-
sonal injury or property damage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101
3

Tire Pressure Display Ð If Equipped
Shows the current pressure of all 4 road tires.
NOTE:Tires heat up during normal driving conditions.
Heat will cause the tire pressure to increase from 2 to 6
psi (14 to 41 kPa) during normal driving conditions. Refer
to ªTire Inflation Pressuresº in Section 5 for additional
information.
Blank Screen
Shows a blank screen. Pressing the C/T button returns to
the compass/temperature display.
Automatic Compass Calibration
This compass is self-calibrating which eliminates the
need to manually set the compass. When the vehicle is
new, the compass may appear erratic and the CAL
symbol will be displayed.
After completing one 360 degree turn, with the vehicle
traveling less than 5 mph (8 km/h), in an area free from
large metal or metallic objects, the CAL symbol will turn
off and the compass will function normally.
Manual Compass Calibration
If the compass appears erratic and the CAL symbol does
not appear, you must manually put the compass into the
ªCalibrationº mode.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

7. Oil Pressure Gage
Indicates the engine oil pressure. This gage does
not measure oil level. Pressure varies with engine
speed, temperature, and oil viscosity. Normal oil pressure
will be midway between the lowest and highest limit
marks.
8. Sentry Key Indicator Light Ð If Equipped
Refer to ªSentry Key Immobilizer Systemº in
Section 2 of this manual for more information.
9. Malfunction Indicator Light
This light is part of an onboard diagnostic system
called OBD II which monitors engine and auto-
matic transmission control systems. This light
will illuminate when the ignition is in the ON position
before engine start. If the bulb does not come on when
turning the ignition key from OFF to ON, have the
condition checked promptly.Certain conditions such has a loose or missing gas cap,
poor fuel quality, etc. may illuminate the light after
engine start. The vehicle should be serviced if the light
stays on through several typical driving cycles. In most
situations, the vehicle will drive normally and will not
require towing.
When the engine is running, the ªMalfunction Indicator
Lightº may flash to alert of serious conditions that could
lead to immediate loss of power or severe catalytic
converter damage. The vehicle should be serviced as
soon as possible if this occurs.
10. Cruise Indicator Light
This indicator lights when the electronic speed
control system is turned ON.
11. Check Gages Warning Light
This light illuminates when the voltmeter, oil
pressure, or temperature gages indicate a reading
130 UNDERSTANDING YOUR INSTRUMENT PANEL

either too high or too low. Examine the gages carefully,
and follow the instructions above for each indicated
problem.
NOTE:When the ignition switch is turned to OFF, the
fuel gage, voltmeter, oil pressure, and temperature gages
will not show any readings. When the engine is not
running, turn the ignition switch to ON to obtain accu-
rate readings.
12. Part Time Indicator Light
This light alerts the driver that the vehicle is in
the PART TIME four±wheel drive mode, and
the front and rear driveshafts are mechanically
locked together forcing the front and rear wheels to rotate
at the same speed.
13. Transmission Over Temperature Warning Light
This light indicates that there is excessive transmis-
sion fluid temperature that might occur with severe
usage such as trailer towing or snow plowing. If this lightcomes on, stop the vehicle and run the engine at idle or
faster, with the transmission in N (Neutral) until the light
goes off.
14. Temperature Gage
Indicates engine coolant temperature. Any read-
ing within the normal range indicates that the
cooling system is operating satisfactorily.
The gage pointer will likely indicate a higher temperature
(above center scale) when driving in hot weather, up
mountain grades, or when towing a trailer. It should not
be allowed to exceed the upper limits of the normal
operating range.
If the pointer rises to the 260É (Hot) mark, pull over and
stop the vehicle. Do not turn the engine off. Idle the
vehicle with the air conditioning turned off, until the
pointer drops back into the normal range.
UNDERSTANDING YOUR INSTRUMENT PANEL 131
4

NSelec-TractOperating
Instructions/Precautions................186
NShift Positions........................188
NShifting Procedure....................189
NQuadra-Trac IItOperating
Instructions/Precautions Ð If Equipped.....191
NShift Positions........................192
NShifting Procedure....................193
NQuadra-DrivetSystem Ð If Equipped......194
mVari-Lok Front And Rear Axles Ð If Equipped . . 194
mParking Brake.........................194
mAnti-Lock Brake System..................197
mOn-Road Driving Tips...................199
mOff-Road Driving Tips...................200NWhen To Use 4 Lo (Low) Range...........200
NIn Snow, Mud And Sand................200
NHill Climbing........................200
NTraction Downhill.....................201
NAfter Driving Off-Road.................202
mTire Safety Information...................203
NTire Markings........................203
NTire Identification Number (TIN)..........206
NTire Loading And Tire Pressure...........207
mTires Ð General Information...............211
NTire Inflation Pressures.................212
NHigh Speed Operation.................213
NRadial-Ply Tires......................214
174 STARTING AND OPERATING

NTire Spinning........................214
NTread Wear Indicators..................215
NReplacement Tires.....................215
NAlignment And Balance.................217
mTire Pressure Monitor System Ð If Equipped . . . 217
NTire Pressure Monitor System Tire/Wheel
Rotation And Sensor Replacement Ð If
Equipped...........................218
NGeneral Information...................219
mTire Chains...........................220
mTire Rotation Recommendations............220
mFuel Requirements......................221
NReformulated Gasoline.................222
NGasoline/Oxygenate Blends..............222NMMT In Gasoline.....................223
NSulfur In Gasoline.....................223
NMaterials Added To Fuel................224
mFuel Tank Filler Cap (Gas Cap).............224
mTrailer Towing.........................226
NTrailer And Tongue Weight..............228
NCooling System TipsÐTrailer Towing.......229
NMinimum Vehicle Requirements For Trailer
Towing............................230
mRecreational Towing (Behind Motorhome, Etc.) . . 231
NShifting Into Neutral (N)................232
NShifting Out Of Neutral (N)..............233
mSnow Plow...........................234
STARTING AND OPERATING 175
5

Rocking the Vehicle
If the vehicle becomes stuck in snow, sand, or mud, it can
often be moved by a rocking motion. Move the gear
selector rhythmically between ªFirstº and R (Reverse),
while applying slight pressure to the accelerator.
The least amount of accelerator pedal pressure to main-
tain the rocking motion without spinning the wheels or
racing the engine is most effective. Racing the engine or
spinning the wheels, due to the frustration of not freeing
the vehicle, may lead to transmission overheating and
failure. Allow the engine to idle with the transmission
selector in N (Neutral) for at least one minute after every
five rocking-motion cycles. This will minimize overheat-
ing and reduce the risk of transmission failure during
prolonged efforts to free a stuck vehicle.CAUTION!
When ªrockingº a stuck vehicle by moving between
ªFirstº and R (Reverse), do not spin the wheels faster
than 15 mph (24 km/h), or drivetrain damage may
result.
FOUR-WHEEL DRIVE OPERATION
Selec-TracTOperating Instructions/Precautions
The Selec-Tracttransfer case provides five mode posi-
tions Ð two (rear) wheel drive high mode, part-time four
wheel drive high range, full-time four wheel drive high
range, neutral, and four wheel drive low range.
This transfer case is equipped with an inter-axle differ-
ential which allows driving the vehicle in the 4 FULL
TIME position at all times on any given road surface
including dry hard surfaced roads. The 4 FULL TIME
186 STARTING AND OPERATING

ANTI-LOCK BRAKE SYSTEM
The Anti-Lock Brake System (ABS) is designed to aid the
driver in maintaining vehicle control under adverse
braking conditions. The system operates with a separate
computer to modulate hydraulic pressure to prevent
wheel lock-up and help avoid skidding on slippery
surfaces.
All vehicle wheels and tires must be the same size and
type and tires must be properly inflated to produce
accurate signals for the computer.
WARNING!
Significant over or under inflation of tires, or mixing
sizes of tires or wheels on the vehicle can lead to loss
of braking effectiveness.
The Anti-Lock Brake System conducts a low-speed self-
test at about 12 mph (20 km/h). If you have your foot
lightly on the brake while this test is occurring you may
feel slight pedal movement. The movement can be more
apparent on ice and snow. This is normal.
The Anti-Lock Brake System pump motor runs during
the self-test at 12 mph (20 km/h) and during an ABS stop.
The pump motor makes a low humming noise during
operation, which is normal.
WARNING!
Pumping of the Anti-Lock Brakes will diminish
their effectiveness and may lead to an accident.
Pumping makes the stopping distance longer. Just
press firmly on your brake pedal when you need to
slow down or stop.
STARTING AND OPERATING 197
5