2004 JEEP GRAND CHEROKEE buttons

Electronic Serial Number/Sirius Identification
Number (ENS/SID)
The Electronic Serial Number/Sirius Identification Num-
ber is needed to activate your Sirius Satellite Radio
system. To access the ESN/SID, refer to the following
steps:
ESN/SID Access With RBB and RBK Radios
With the ignition switch in the ACCESSORY position and
the radio OFF, press the Tape Eject or CD Eject (depend-
ing on the radio type) and Time buttons simultaneously
for 3 seconds. The first four digits of the twelve-digit
ESN/SID number will be displayed. Press the SEEK UP
button to display the next four digits. Continue to press
the SEEK UP button until all twelve ESN/SID digits have
been displayed. The SEEK DOWN will page down until
the first four digits are displayed. The radio will exit the
ESN/SID mode when any other button is pushed, the
ignition is turned OFF, or 5 minutes has passed since any
button was pushed.
ESN/SID Access With RBP, RBU, RAZ, and RBQ
Radios
With the ignition switch in the ACCESSORY position and
the radio OFF, press the CD Eject and TIME buttons
simultaneously for 3 seconds. All twelve ESN/SID num-
bers will be displayed. The radio will exit the ESN/SID
mode when any other button is pushed, the ignition is
turned OFF, or 5 minutes has passed since any button
was pushed.
Selecting Satellite Mode in RBB and RBK Radios
Press the MODE button repeatedly until9SA9appears in
the display. A CD or tape may remain in the radio while
in the Satellite radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 153
4

Selecting Satellite Mode in RBP, RBU, RAZ, and
RBQ Radios
Press the MODE button repeatedly until the word
9SIRIUS9appears in the display. These radios will also
display the following:
²After 3 seconds, the current channel name and channel
number will be displayed for 5 seconds.
²The current program type and channel number will
then be displayed for 5 seconds.
²The current channel number will then be displayed
until an action occurs.
A CD or tape may remain in the radio while in the
Satellite radio mode.
Selecting a Channel
Press and release the SEEK or TUNE buttons to search for
the next channel. Press the top of the button to search up
and the bottom of the button to search down. Holding the
TUNE button causes the radio to bypass channels until
the button is released.
Press and release the SCAN button (if equipped) to
automatically change channels every 7 seconds. The
radio will pause on each channel for 7 seconds before
moving on to the next channel. The word9SCAN9will
appear in the display between each channel change. Press
the SCAN button a second time to stop the search.
NOTE:Channels that may contain objectionable content
can be blocked. Contact Sirius Customer Care at 888-539-
7474 to discuss options for channel blocking or unblock-
ing. Please have your ESN/SID information available.
154 UNDERSTANDING YOUR INSTRUMENT PANEL

²Floor
Air flows through the floor outlets located under
the instrument panel and into the rear seating
area through vents under the front seats.
²Bi-Level
Air flows both through the outlets located in the
instrument panel and those located on the floor.
²Panel
Air flows through the outlets located in the in-
strument panel.
²OFF
This position turns off the entire system.
Depress the A/C button to turn on and off the air
conditioning during manual operation only. Conditioned
outside air is then directed through the outlets selected
on the mode control dial.When the outside air contains smoke, odors, high humid-
ity, or if rapid cooling is desired you may wish to
recirculate interior air by pressing the ªRecirculateº icon
button. The recirculation mode should only be used
temporarily. The light on the A/C and ªRecirculateº icon
buttons will illuminate when these buttons are selected.
You may use these features separately or with one
another. Push in on the buttons a second time to change
the functions.
NOTE:If the interior of the windows begins to fog,
press the ªRecirculateº icon button to return to outside
air. Some temp./humidity conditions will cause captured
interior air to condense on windows and hamper visibil-
ity. For this reason, the system will not allow ªRecircu-
lateº to be selected while in the defrost or defrost/floor
modes.
To provide you with maximum comfort in the automatic
mode, during cold start-ups the blower fan will remain
UNDERSTANDING YOUR INSTRUMENT PANEL 169
4