2004 JAGUAR XJ tow

6 - 4 Roadside Emergency
Trunk Underfloor Access
The space under the trunk floor houses
the spare wheel, battery, jack and rear
fuse box.
To raise the floor panel, press down the
rear of handle (A) then, holding the
handle at the front, swing the floor panel
upwards ( B). Hook the handle securely
over the top edge of the trunk
opening ( C).
Emergency Starting
This vehicle is fitted with automatic
transmission. In the event of a discharged
battery preventing a normal engine start,
the vehicle cannot be started by pushing
or towing. Either use jump leads
connected to a booster battery (e.g. on
another vehicle) or fit a fully charged
battery (see page 7 - 15).
Emergency Starting Using
Jump Leads
Both the booster and discharged battery
should be treated with great care when
using jump leads. Al ways use high quality
leads capable of carrying the starter
current of the vehicle to be started.
Before commencing, the following
precautions must be taken:
• When the battery of another vehicle is being used, ensure that the vehicles
do not touch. Alternatively, remove
the charged battery and place near to,
not on, the vehicle with the
discharged battery.
• Ensure that both vehicles have all electrical services OFF,
the parkbrakes applied and the
transmission in the ‘P’ (park) position.
• Where the jump leads are of a different colour, e.g. red and black,
use red for positive (+). This aids
identification and helps to avoid
crossing positive (+) to negative (–).
Take extra care to avoid crossing the
polarity when using cables of the
same colour.

6 - 6 Roadside Emergency
Wheel Changing and
Jacking
Be prepared for a flat tyre. Know where
equipment is stowed and read the wheel
changing and jacking instructions
carefully. Keep the jack screw threads
clean and greased to ensure it is always
ready for an emergency.
Park off the road, clear of all traffic and
on as level, solid ground as possible.
Switch on hazard warning lights and,
where legally required, display the
warning triangle.
!WARNING:
It can be dangerous to change a
wheel when the vehicle is on a slope
or soft, uneven ground.
Temporary-use Spare Wheel
Note: Maintenance information for the
temporary-use spare wheel is the same as
given for normal tyres.
Observe the following warnings before
using the wheel:
!WARNING:
1. Please note th e temporary-use
spare wheel warning label on the
wheel. Adhere to instructions on
the label. Failure to comply can be
dangerous.
2. When a temporary spare wheel is fitted, drive with caution and
replace with the specified wheel
and tyre as soon as possible.
3. Do not fit more than one temporary-use spare wheel and
tyre assembly at a time.
4. The temporary-use spare wheel must be inflated to the correct
pressure.
5. Temporary-use spare wheel maximum speed is 80 km/h
(50 mph).

6 - 10 Roadside Emergency
!WARNING:
1. Do not attempt to lift the vehicle unless the jack head is fully
engaged in the jacking point.
2. Ensure that the parkbrake is applied.
Place the jack squarely beneath the
appropriate jacking point. Ensure that the
jack head is fully engaged. Carefully raise
the vehicle by turning the handle.
Stop jacking the vehicle when the tyre
just clears the ground. Minimum tyre lift
gives maximum vehicle stability.
Remove the wheel nuts and the wheel.
Centre badge
When changing the alloy road wheels,
transfer the centre badge to the
replacement wheel. Using the plastic
tipped end of the wheel nut wrench
handle from the inside of the wheel, push
the centre badge from its housing.
Push the centre badge into the
replacement wheel. Fitting the spare wheel
Fit the spare wheel and loosely secure
with the wheel nuts.
Using the wheel nut wrench, lightly
tighten the wheel nuts
alternately using
the sequence shown in the illustration.
Lower the jack and ti ghten the wheel nuts
alternately, DO NOT OVER TIGHTEN.
At the earliest opportunity have the
wheel nuts tightened with a torque
wrench to 92 lb.ft (125 Nm).
This torque must not be exceeded. Stowing the equipment
Stow the replaced road wheel in the
trunk.
Check that the locking ring is unscrewed
fully so that it is as close as possible to the
handle of the wheel retainer. This is to
ensure that the wheel retainer can be
fitted correctly.
Locate the wheel retainer into its mating
thread in the trunk floor and tighten it
fully, then tighten the locking ring
clockwise to secure the wheel.
Seepage6-8.
Stow the jacking equipment.
Close the trunk floor panel.
!WARNING:
When a temporary spare wheel is
fitted, drive with caution and replace
with the specified wheel and tyre as
soon as possible.

Roadside Emergency 6 - 11
Vehicle Recovery
The preferred vehicle recovery method is
by using a flat bed transporter or rear
suspended tow.
Caution:
1. If the vehicle has defective transmission, to prevent further
damage, it must be towed with
the rear wheels clear of the
ground.
2. Ensure that the recovery team do not tow with sling-type
equipment since damage to the
bodywork may result.
3. Do not tow the vehicle by suspending the front end.
Transporting
If the vehicle is being transported on a
trailer or flat bed transporter,
the parkbrake must be applied,
the wheels chocked and the gear selector
lever moved to position ‘N’ or ‘D’ but
NEVER to ‘P’.
The vehicle must be securely tied down
to the transporter or trailer, see next
page.

6 - 12 Roadside Emergency
Transporter tie-down procedure
!WARNING:
Avoid body contact with a hot
exhaust pipe when securing the
vehicle to the transporter.
IMPORTANT – Use straps over the
wheels/tyres only, to secure the vehicle to
the transporter.
Caution: Do not use the tie-down
brackets on the vehicle rear
underbody; these are for Jaguar
factory use only. In time, with the
engine switched off, the vehicle body
will drop due to settling of the air
suspension system and cause the tie-
down chains/straps to become slack if
connected to these brackets.
The towing eye is not designed for
securing the vehicle during
transportation. Vehicle failure
The removable towing eye is primarily for
emergency use when towing for SHORT
DISTANCES, e.g. removing the vehicle if it
is causing an obstruct
ion or for winching
the vehicle onto a re covery transporter.
To prevent damage to the automatic
transmission whilst the vehicle is being
towed with the rear wheels on the
ground, towing distance must be
restricted to 0.5 miles (0.8 kilometres).
Towing speed must not exceed 30 mph
(48 km/h).
Always obey towing regulations.
In certain countries the registration
number of the towing vehicle and an
‘ON TOW’ sign or warning triangle must
be displayed in a prominent position at
the rear of the vehicle being towed. When being towed, the gear selector
lever must be in neutral (position ‘N’)
with the ignition key turned to
position ‘II’ to release the steering lock
and render the indicators, horn and
brake lights operational.
!WARNING:
When the engine is not running the
steering and brakes will no longer be
power-assisted.
Therefore, be prepared for relatively
heavy steering and the need for
greatly increased brake pedal
pressure.

Roadside Emergency 6 - 13
Towing Eye
A screw-in towing eye is provided in the
trunk with the jack and can be fitted to
the front or rear of the vehicle.
The towing eye has a left-hand thread
and must be turned in an anti-clockwise
direction when fitting.
Caution:
1. The towing eye is not suitable for ‘solid bar’ towing.
2. Care must be taken to avoid damaging the bumpers and front
apron. Front tow point
The front tow point is located behind a
plastic cover (shown
above) on the left-
hand side of the vehicle, as viewed from
the front.
To remove the cover, unclip the top edge,
pivot down and unclip the bottom edge.
Screw the towing ey e into the vehicle,
right up to the shoulder, turning anti-
clockwise.
To refit the cover (towing eye removed)
first clip the lower edge to the bumper
aperture, pivot up and press the top edge
into position. Rear tow point
!WARNING:
Avoid body contact with a hot
exhaust pipe when fitting the eye to
the rear towing point.
The rear tow point is alongside the left-
hand exhaust pipe.
Screw the towing eye into the vehicle,
right up to the shoulder, turning anti-
clockwise.

Roadside Emergency 6 - 17
Side repeater indicator – bulb renewal
To remove the light unit from the front wing, push the lens
towards the front of the vehicle to compress the spring clip and
then pull the rear outwards to remove the complete unit.
Twist the bulb holder anti-clockwise and pull it from the lens.
Pull the capless bulb from the holder and fit a new one of the
correct type, W5W. Fit the bulb holder to the lens and twist
clockwise to secure.
Place the inner rear of the lens unit into the recess and then
push the front of the lens inwards until it clicks into place. Number plate light – bulb renewal
Press the two lens clips inwards and remove the lens from the
vehicle.
Remove the bulb and fit a new
one of the correct type, W5W.
Refit the lens by pressing it firmly into the recess until it clicks
into place.
Front fog light – bulb renewal
It is recommended that the front fog light bulb, type H3,
is renewed by a Jaguar Retailer.

Roadside Emergency 6 - 27
F17 ATO 5A Tan ABS module
F18 Not used
F19 ATO 5A Tan Ignition relay, ECM, REM, fuel pump relay, start relay
F20 ATO 5A Tan Telephone transceiver, TV module, VICS (Japan), voice module, rear telematics
F21 – F23 Not used
F24 ATO 10A Red PATS transponder
F25 ATO 10A Red Right-hand direction indicator and repe ater, right-hand front lamp, header console map
lamp
F26 ATO 15A Blue Screenwash pump
F27 ATO 10A Red ACC module
F28 ATO 10A Red Climate control modules (front and rear), driver’s door module (DDM)
F29 ATO 10A Red Air bag module, occupancy se nsing module, passenger weight sensor
F30 ATO 10A Red Voice, front/rear sound, DVD, telematics, TV
F31 ATO 15A Blue Sunroof
F32 ATO 5A Tan Front/rear parking aid, trailer tow module, battery backed sounder, voice module, telephone receiver
F33 ATO 5A Tan Transmission control, J-gate, generator
F34 ATO 5A Tan Navigation system
Fuse No
Fuse
Type Rating
(amps) Colour
Circuit