2004 ISUZU TF SERIES OBD port

7A2-62 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Action Taken When The DTC Sets

The TCM operates shifting as following pattern.



Normal Fail S1 S2
1 3 - on
2 3 - on
3 3 - on
4 4 - off

No squat control.
 No engine torque control.

No line pressure control.

No lock-up control.
 No slope control.

Check Trans ON.

DTC stored.

No detect DTC P0722

No detect DTC P0717

Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.


DTC P0753 (FLASHING CODE 31) Shift Solenoid S1 Electrical


Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".
3. Review and record scan tool data.

4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P0753? — Go to Step 3 Refer to
Diagnostic Aids
3

1. Key “ON", engine run.

2. Place the selector lever in the "P" range.
3. Measure the voltage between terminal C94-16 and
terminal C94-1 on the TCM pigtail connector by
J39200 DMM.
Is the voltage specified value? 816V Go to Step 4 Go to Step 10

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-65

Action Taken When The DTC Sets
The TCM operates shifting as following patterns.



Normal Fail S1 S2
1 3 - on
2 3 - on
3 3 - on
4 4 - off

No squat control.
 No engine torque control.

No line pressure control.

No lock-up control.
 No slope control.

No torque reduction.

Check Trans ON.

DTC stored.

No detect DTC P0722.

No detect DTC P0717.

Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring .
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.


DTC P0758 (FLASHING CODE 32) Shift Solenoid S2 Electrical


Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".

3. Review and record scan tool data.
4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P0758? — Go to Step 3 Refer to
Diagnostic Aids
3

1. Key “ON", engine run.

2. Place the selector lever in the "P" range.
3. Measure the voltage between terminal C94-15 and
terminal C94-1 on the TCM pigtail connector by
J39200 DMM.
Is the voltage specified value? 816V Go to Step 4 Go to Step 10

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-69

DTC P1767 (FLASHING CODE 67) ECM CAN Invalid

Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".

3. Review and record scan tool data.
4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC P1767? — Go to Step 3 Refer to
Diagnostic Aids
3 Observe the valid data of the ECM on the scan tool.
Was the valid data of the ECM fixed or did not
synchronized? — Go to Step 4 Refer to
Diagnostic Aids
4 Check the wire between the TCM connector and the
ECM connector by J39200 DMM.

1. Key “OFF".
2. Disconnect the TCM connector.

3. Measure the resistance between terminal C94-7
and terminal C94-17.
Is the resistance specified value? About 120
Go to Step 5 Go to Step 7
5 Check the resistance of the ECM..

1. Key “OFF".
2. Disconnect the ECM connector.

3. Measure the resistance between the ECM terminal
E60-70 and the ECM terminal E60-71.
Is the resistance specified value? About 120
Go to Step 6 Go to Step 8
6 Replace or Repair the wire between the TCM
connector C94-7,17 and the ECM connector E60-
70,71.
Is the action complete? — Verify repair —
7 Replace the TCM.
Important:
The replacement TCM must be
programmed (Refer toSPS for procedure).
Is the action complete? — Verify repair —
8 Replace the ECM.
Important:
The replacement ECM must be
programmed (Refer to SPS for procedure).
Is the action complete? — Verify epair —

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-71

DTC P1790 (FLASHING CODE 61) Transmission Control Module ROM
Checksum Error


Step Action Value(s) YES NO
1
Was the Powertrain ON-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “OFF" and keep the position for more than 30
seconds.
3. Key “ON".

4. Check the DTC on the scan tool.
Does the scan tool indicate DTC P1791? — Go to Step 3 Refer to
Diagnostic Aids
3 Perform the SPS for the TCM.
Is the action complete? — Go to Step 4 —
4 Recheck the DTC on the scan tool.
Does the scan tool indicate DTC P1790? — Go to Step 5 Verify repair
5 Replace the TCM.
Important:
The replacement TCM must be
programmed (Refer to SPS for procedure).
Is the action complete? — Verify repair —

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-73

DTC P1791 (FLASHING CODE 62) Transmission Control Module RAM Error

Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “OFF" and keep the position for more than 30
seconds.
3. Key “ON"

4. Check the DTC on the scan tool.
Does the scan tool indicate DTC P1791? — Go to Step 3 Refer to
Diagnostic Aids
3 Replace the TCM.
Important:
The replacement TCM must be
programmed (Refer to SPS for procedure).
Is the action complete? — Verify repair —

7A2-76 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

DTC U2104 (FLASHING CODE 65) CAN BUSS OFF

Step Action Value(s) YES NO
1
Was the Powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".
3. Review and record scan tool data.

4. Operate the vehicle within scan tool data.
Does the scan tool indicate DTC U2104? — Go to Step 3 Refer to
Diagnostic Aids
3 Observe the valid data of the ECM on the scan tool.
Was the valid data of the ECM fixed or did not
synchronized? — Go to step 4 Refer to
Diagnostic Aids
4 Check the wire between the TCM connector and the
ECM connector by J39200 DMM.

1. Key “OFF".
2. Disconnect the TCM connector.

3. Measure the resistance between terminal C94-7
and terminal C94-17.
Is the resistance specified value? About 120
Go to Step 7 Go to Step 5
5 Check the resistance of the ECM..

1. Key "OFF".

2. Disconnect the ECM connector.
3. Measure the resistance between the ECM terminal
E60-70 and the ECM terminal E60-71.
Is the resistance specified value? About 120
Go to step 6 Go to step 8
6 Replace or Repair the wire between the TCM
connector C94-7,17 and the ECM connector E60-
70,71.
Is the action complete? — Verify repair —
7 Replace the TCM.
Important:
The replacement TCM must be
programmed (Refer to SPS for procedure).
Is the action complete? — Verify repair —
8 Replace the ECM.
Important:
The replacement ECM must be
programmed (Refer to SPS for procedure).
Is the action complete? — Verify repair —