2004 ISUZU TF SERIES change time

7A2-40 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Condition 2 ("Short"):
When the TCM detects 2 times or more signals o
f
range sensor more than 0.025 sec at following
conditions.

Vehicle speed is more than 19 mph.
 Engine speed is more than 1500 rpm.
Action Taken When The DTC Sets

No 3rd start mode.
 No slope control.

The TCM judges always D range position of range
sensor at "Condition 1".

The TCM judges the position of range sensor with
following priority at "Condition 2".

There is a priority in order of D, 3, 2, L, R, N, and P.

Check Trans ON.

DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.

Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.
 Check range sensor for proper mounting and
adjustment.

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-61

DTC P0753 (FLASHING CODE 31) Shift Solenoid S1 Electrical



RTW37ALF000601

Circuit Description
The shift solenoi S1 changes the hydraulic route with
the signals from the TCM according to the vehicle
speed and the throttle opening to control shifting. When
the solenoid S1 or S2 fails, the hydraulic circuit is
mechanically operated as a backup.

Condition for setting the DTC
The TCM detects following "Condition 1" and "
Condition 2" for 2 times continuously at shifting.
Condition 1("GND short"):

Voltage at connector pin is 0V for 0.3 sec
continuously when solenoid is “ON".
Condition 2("Open or Ignition short"):

Voltage at connector pin is ignition voltage for 0.5
sec continuously when solenoid is “OFF".

7A2-64 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

DTC P0758 (FLASHING CODE 32) Shift Solenoid S2 Electrical


RTW37ALF000601

Circuit Description
The solenoid S2 changes the hydraulic route with the
signals from the TCM according to the vehicle speed
and the throttle opening to control shifting. When the
solenoid S1 or S2 fails, the hydraulic circuit is
mechanically operated as a backup.

Condition for setting the DTC
The TCM detects following "Condition 1" and "Condition
2" for 2 times continuously at shifting.
Condition 1 ("GND short"):

Voltage at connector pin is 0V for 0.3 sec
continuously when solenoid is “ON".
Condition 2 ("Open or Ignition short"):

Voltage at connector pin is ignition voltage for 0.5
sec continuously when solenoid is “OFF".

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-67

DTC P1767 (FLASHING CODE 67) ECM CAN Invalid

RTW37AMF000401

Circuit Description
The automatic transmission control system in AW30-
40LE uses high speed CAN bus system. The individual
CAN bus systems are connected via two interfaces and
can exchange information and data. This allows control
modules that are connected to different CAN bus
systems to communicate. Transmission control
modules in the vehicle that require continuous, rapid
communication are connected to the high speed CAN
bus. The automatic transmission is continuously notified
of the current engine load status. Since the automatic
transmission control module has to react immediately to
load status changes, rapid communication is required
between the engine control module and the automatic
transmission control module. The high speed CAN bus
in the AW30-40LE is designed as a two-wire CAN bus
(twisted pair). The wires are shielded and twisted. The
transmission rate is 500K band.

Condition for setting the DTC
The TCM detects invalid signal for 0.18 sec. (After the
TCM leaves a communication start with the ECM fo
r
0.64 sec)
The TCM detects above condition for 2.0 sec
continuously.
Action Taken When The DTC Sets

The line pressure is max.
 The TCM judges APS(Accelerator Position Sensor)
angle is 0% at the time of shift operation.

No line pressure control.

No engine torque control.
 No lock-up control.

No slope control.

Check Trans ON.

DTC stored.

No squat control.

7A2-74 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

DTC U2104 (FLASHING CODE 65) CAN BUSS OFF

RTW37AMF000401

Circuit Description
The automatic transmission control system in AW30-
40LE uses high speed CAN bus system. The individual
CAN bus systems are connected via two interfaces and
can exchange information and data. This allows control
modules that are connected to different CAN bus
systems to communicate. Transmission control
modules in the vehicle that require continuous, rapid
communication are connected to the high speed CAN
bus. The automatic transmission is continuously notified
of the current engine load status. Since the automatic
transmission control module has to react immediately to
load status changes, rapid communication is required
between the engine control module and the automatic
transmission control module. The high speed CAN bus
in the AW30-40LE is designed as a two-wire CAN bus
(twisted pair). The wires are shielded and twisted. The
transmission rate is 500K band.

Condition for setting the DTC
The TCM detects CAN BUS OFF for 0.18 sec (After the
TCM leaves a communucation start with the ECM fo
r
0.64 sec) continously..
Action Taken When The DTC Sets

The throttle pressure is max.

The TCM judges APS(Accelerator Position Sensor)
angle is 0% at the time of shift operation.
 No throttle pressure reduction.

No torque reduction.

No lock-up control.
 No slope control.

No squat control.

Check Trans ON.

DTC stored.

Engine REV is 7000 rpm.
 Coolant tempreature is 80

C.

ON-VEHICLE SERVICE (AW30–40LE) 7A3-1
TRANSMISSION
ON-VEHICLE SERVICE (AW30–40LE)
CONTENTS

Service Precaution .................................................
7A3-2
Location of Clutch, Brake, One-Way Clutch
and Solenoid ........................................................
7A3-3
Operation of Clutch, Brake and One-Way
Clutch ....................................................................
7A3-4
Trnasmission Indentification ..............................
7A3-4
Speed Change and Lock-Up Pattern ...............
7A3-5
Overdrive and Lock-Up Operating
Conditions ............................................................
7A3-5
Diagnosis .................................................................
7A3-6
Basic Troubleshooting ........................................
7A3-6
Manual Shifting Test ...........................................
7A3-12
Stall Test ..............................................................
7A3-12
Time Lag Test .....................................................
7A3-13
Hydraulic Test ......................................................
7A3-14
Road Test .............................................................
7A3-15
Shift Pont Chart and Lock-Up Point Chart ..........
7A3-19
Shift Pont Chart ...................................................
7A3-19
Lock-Up Point Chart ...........................................
7A3-20
Transmission Fluid Level and Condition .............
7A3-21
Inspection .............................................................
7A3-21
ATF Replacement ..................................................
7A3-22
Inspection .............................................................
7A3-22
Neutral Start Switch (Mode Switch) .....................
7A3-23
Inspection .............................................................
7A3-23
Removal ...............................................................
7A3-23
Installation ............................................................
7A3-23
Brake Signal ............................................................
7A3-24
Inspection .............................................................
7A3-24
Input and Output Revolution Sensor ....................
7A3-25
Inspection .............................................................
7A3-25
Pattern Select Switch .............................................
7A3-25
Inspection .............................................................
7A3-25
Solenoid ...................................................................
7A3-26
Inspection .............................................................
7A3-26

ATF Temperature Sensor ......................................
7A3-27
Inspection .............................................................
7A3-27
Select Lever ....................................................... 7A3-28 Remove or Disconnect .......................................
7A3-28
Install or Connect .................................................
7A3-29
Shift Cable ......................................................... 7A3-31
Remove or Disconnect .......................................
7A3-31
Install or Connect .................................................
7A3-32
Torque specifications ..........................................
7A3-33
Transmission Control Module (TCM) ...................
7A3-34
Removal ................................................................
7A3-34
Installation .............................................................
7A3-34
Shift Solenoid and Lock-Up Solenoid ...................
7A3-35
Removal ................................................................
7A3-35
Installation .............................................................
7A3-36
Valve Body Assembly and Pressure Control Solenoid .................................................
7A3-37
Removal ................................................................
7A3-37
Installation .............................................................
7A3-39
Rear Oil Seal (Adapter Housing, 4

4) .................
7A3-40
Removal ................................................................
7A3-40
Installation .............................................................
7A3-40
Rear Oil Seal (Extension Housing, 4
2) ..............
7A3-41
Removal ................................................................
7A3-41
Installation .............................................................
7A3-41
Transmission Assembly .........................................
7A3-42
Transmission and Associated Parts .................
7A3-42
Removal ................................................................
7A3-43
Installation .............................................................
7A3-46
Major Components ..............................................
7A3-50

7A3-12 ON-VEHICLE SERVICE (AW30 –40LE)

Manual Shifting Test
NOTE: With this test, it can be determined whether the
trouble lies within the electrical circuit or is a mechanical
problem in the transmission.
1. Disconnect TCM connector
Inspect manual driving operation
2. Inspect manual driving operation
Check that the shift and gear positions correspond
with the table.
If the “L", “2", “3" and “D" range gear positions are
difficult to distinguish, do perform the following road
test.
While driving, shift through the “L", “2", “3" and “D"
ranges. Check that the gear change corresponds to
the gear position.
If any abnormality is found in the above test, do
perform the stall, time lag or gear change tests.



RUW37ASH004101
3. Connect TCM connector
With the engine off, connect the TCM connector.


Stall Test



RUW37ALH000101
The object of this test is to check the overall
performance of the transmission and engine b
y
measuring the maximum engine speeds at the “D" and
“ R" ranges.
NOTE:
1. Perform the test at normal operation fluid
temperature (50 – 80 
C or 122 – 176 
F).
2. Do not continuously run this test longer than 5 seconds.

7A3-32 ON-VEHICLE SERVICE (AW30 –40LE)

Install or Connect
1.
Install the shift cable toward the inside of the cabin
from the bottom of the vehicle.
2.
Push the shift cable into the select lever base.
3.
Connect the shift cable to the select lever.
4.
Fix the shift cable to the bracket.
Install the clip on the marking of shift cable.
5.
Check that the select lever is in the “N ” position.
6.
Check that the transmission is in the “N ” position.




249R300002
7.
Slide the cover in the direction shown by the arrow
(1).
8.
Use an ordinary screwdriver to move the lock piece
from the position indicated by the arrow (2). Continue
to move the lock piece until the adjuster position
begins to change.

P1010012

9.
Connect the shift cable to the manual shaft select
lever at the transmission side.
10.
Insert the lock piece to the adjuster (cable length
adjustment).
11.
Slide the cover on the adjuster and secure lock
piece.

P1010016-2
11.
Press the select lever knob button 5 times.
Then check that the select lever moves smoothly to each of its positions.
13.
Check that the shift position indicated by the select
lever and the actual shift position are the same.
14.
Install the front console and rear console.
15.
Connect the negative battery cable.
16.
Remove the wheel blocks.