2004 ISUZU TF SERIES engine oil
[x] Cancel search: engine oilPage 4096 of 4264
7A2-104 DIAGNOSIS (JR405E)
No. B5: Engine Stalls When Selecting From N Range to
R, D, 3, 2 or L Range
Description:
The engine stalls when selecting from N or P range to a run range during the engine idling.
Diagnosis Hints:
As causes attributable to the engine, faulty idle up, insufficient engine output, etc. are considered.
As a cause of the AT system, faulty lockup piston system (lockup engine stall) is considered.
If the oil through resistance increases remarkably due to clogged oil cooler or some other reason, or if the ATF
level decreases, the lock-up piston works causing the engine stall.
Possible Cause:
Disordered idling speed, faulty idle up, faulty engine output, shortage output.
Insufficient ATF quantity (dropped level).
Clogged oil cooler (foreign substance mixed in).
Faulty lock-up piston (clogged oil passage of solenoid drive circuit, faulty operation).
Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.
Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Check of engine idle up speed
Does the idle speed increase when the air conditioning or other
electric load is turned on?
Go to Step 5
Repair the defect or
replace.
Page 4098 of 4264
7A2-106 DIAGNOSIS (JR405E)
No. B6: Engine Starter Does Not Run in P or N Range
No. B7: Engine Starter Runs Except in P or N Range
Description:
The engine starter does not run though the P or N range is selected.
The engine starter runs though the R or D, 3, 2or L range is selected.
Possible Cause:
Disordered select cable.
Disordered Inhibitor switch, disconnection or short-circuit of inhibitor switch.
No. B8: Extended Time Lag When Shift Lever is Changed to N to D
Description:
The shift time lag is longer than standard value when shift lever is changed to N to D.
Possible Cause:
Forward range line pressure is low.
Slip of low & reverse clutch.
Slip of low one-way clutch.
Trouble in control valve body (faulty operation, sticking, clogged oil passage).
Faulty low clutch duty solenoid operation.
Shortage or faulty quality of ATF.
No. B9: Extended Time Lag When Shift Lever is Changed to N to R
Description:
The shift time lag is longer than standard value when shift lever is changed to N to R.
Possible Cause:
Reverse range line pressure is low.
Slip of low & reverse brake.
Slip of reverse clutch.
Trouble in control valve body (faulty operation, sticking, clogged oil passage).
Faulty low & reverse brake duty solenoid operation.
Shortage or faulty quality of ATF.
Page 4100 of 4264
7A2-108 DIAGNOSIS (JR405E)
No. C1: Engine Race Up (Slip) When Gear is Shifted Up to 1st to
2nd
No. C2: Engine Race Up (Slip) When Gear is Shifted Up to 2nd to
3rd
No. C3: Engine Race Up (slip) When Gear is Shifted Up to 3rd to
4th
No. C4: Engine Race Up (Slip) When Gear is Shift Down or Kick-
down to 4th to 3rd
No. C5: Engine Race Up (Slip) When Gear is Shift Down or Kick-
down to 4th to 2nd
No. C6: Engine Race Up (Slip) When Gear is Shift Down or Kick-
down to 3rd to 2nd
No. C7: Engine Race Up (Slip) When Gear is Shift Down or Kick-
down to 4th or 3rd to 1st
No. C8: Engine Race Up (Slip) Others
Description:
The engine speed up when the accelerator pedal is stepped on for acceleration and the gear is shifted up.
The engine speed up when the accelerator pedal is stepped on for acceleration and the gear is shifted down or
for kick-down during steady run.
The engine speed up when the accelerator pedal is stepped on for acceleration and the gear is shifted down or
for kick-down during steady run.
Diagnosis Hints:
Possibility of slip of clutch is supposed. If slip of clutch has occurred, a DTC of "Gear ratio error" is stored.
Possible Cause:
Slip of clutch.
If slip of clutch is caused, a DTC (gear ratio error) is stored.
Dropped line pressure.
Trouble in control valve body (faulty operation, sticking, clogged oil passage).
Page 4124 of 4264
7A2-132 DIAGNOSIS (JR405E)
No. G3: Creep Force is small
Description:
Vehicle does not move though a run range is selected on a flat road during the idling.
Diagnosis Hints:
When the creep force is small in all ranges, low engine output is considered. Another possible cause is slip of
clutch. If the creep is normal only in the R range, operation of the fail-safe function due to a trouble in the electrical
system is considered.
Possible Cause:
Slip of clutch (low clutch).
If slip of clutch is caused, a DTC (gear ratio error) is stored.
Low engine output (low idling speed, out of injection timing, lowered compression pressure, etc.).
Shortage or faulty quality of ATF.
Disconnection or short circuit of solenoid valve output.
Clogged oil passage of solenoid valve output.
Faulty ground return line in AT assembly.
If the ground return line earth is faulty, clutch pressure may decrease causing slip of the clutch.
Trouble in the torque converter system (faulty operation).
Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or
more in each range: Start in the L range (1st) to 2 range
(2nd) to 3 range (3rd) to D range (4th) (to detect the gear
ratio trouble exactly, this process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal? If the ATF level is low,
replenish up to the
specified level.
Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of the
clutch is supposed.
Overhaul the AT unit.
4 Are the idling speed and other engine system normal?
Go to Step 5
Repair the defect or
replace.
5 Is the stall revolution normal in D, 3, 2 and L range? Refer
the STALL TEST section in this manual.
Go to Step 6
Repair the defect or
replace.
6 Is the line pressure normal? Refer the LINE PRESSURE
TEST section in this manual. Trouble in the AT
assembly or control
valve.
Repair the defect or
replace.
Page 4125 of 4264
DIAGNOSIS (JR405E) 7A2-133
No. G4: Large Noise During Idling with the Vehicle in Stop State
Description:
The transmission is noisy during the idling speed in all ranges.
Diagnosis Hints:
Causes such as solenoid operating sound or faulty oil pump are considered.
Distinguishing to some extent is possible by stopping the solenoid operation temporarily, checking the correlation
for the former case and, changing the line pressure and confirming the correlation with noise.
As a matter of course, noise may be generated around the engine, for instance, other than the AT and should be
checked carefully.
Note:
When the noise is generated only at the time of gear shift, it may be the sound of flowing ATF or gear
noise. If the sound varies depending on the gear speed to be shifted, it may be the gear noise generated
from the planetary gear and its related components. If the sound varies depending on the vehicle
speed, it may be the gear noise of the output system, and if varying depending on the engine speed, it
may be the gear noise of the input system or faulty torque converter.
In either case, sound may be "noise" depending on the origin and resonance object. When the object
generating the sound (resonance object) and the sound source (vibration source) are different,
investigation of the cause may be difficult.
No. H1: Judder Occurs at the Lock-up
Diagnosis Hints:
The vehicle body judders at lock-up.
Diagnosis Hints:
Slip due to burning of the lockup piston or insufficient fastening due to dropped working pressure are considered.
Trouble diagnosis flow is basically the same as "No. I1: No lock-up".
Note:
When the lock-up piston has burnt, foreign material mixed in the oil cooler is considered. In such a
case, inspect the oil cooler circuit for clogging of the oil cooler.
No. H2: Large Lock-up Shock
No. H3: Lock-up Point is High or Low
Description:
Large shock is felt at lock-up.
Lock-up point is excessive high or low.
Diagnosis Hints:
Out of properties of input sensor or faulty lock-up piston pressure system are considered.
Trouble diagnosis flow is basically the same as "No. I1: No lock-up".
Page 4128 of 4264
7A2-136 DIAGNOSIS (JR405E)
No. J1: Oil Leaks from Breather
Description:
Oil leaks from breather.
Possible Cause:
ATF quantity is excessively.
No. J2: Oil Leaks Between Engine and Converter Housing
No. J3: Oil Leaks Between Main Case and Converter Housing
No. J4: Oil Leaks Between Main Case and Rear Housing
No. J5: Oil Leaks from Oil Pan
No. J6: Oil Leaks from Manual Shaft Oil Seal
No. J7: Oil Leaks from Oil Cooler Pipe Joint
Description:
Oil leaks between engine and converter housing.
Oil leaks between converter housing and main case.
Oil leaks between main case and rear housing.
Oil leaks from oil pan.
Oil leaks from manual shaft oil seal.
Oil leaks from oil cooler pipe joint.
Possible Cause:
Faulty oil seal or sealing of contact surface is considered.
No. Z1: Transmission Overheat
Description:
You smell the transmission burning.
The transmission smokes.
Possible Cause:
Slip of clutch.
If slip of clutch is caused, a DTC (gear ratio error) is stored.
Clogged oil cooler (foreign substance mixed)
ATF stirred excessively (too much ATF).
Faulty torque converter operating pressure.
Faulty lock-up piston.
Page 4130 of 4264
7A2-138 DIAGNOSIS (JR405E)
No. Z6: Poor Fuel Consumption
Description:
Poor fuel consumption.
Diagnosis Hints:
Basically same causes as "No. C1 - C8: Engine races up (slip) by shift up or shift down" are considered.
No. Z7: Pattern Select Switch is Faulty
Description:
Shift pattern does not change though the pattern select switch is turned on.
Possible Cause:
Faulty mode select switch is considered.
No. Z8: Oil is Splashed During the Running
Description:
Oil is splashed during the running
Possible Cause:
ATF quantity is too high.
No. Z9: Abnormal Smell
Description:
Abnormal smell.
Diagnosis Hints:
Basically a trouble in the AT main unit.
No. Z10: ATF Quantity is Low or High
Description:
Oil quantity is low or high.
Possible Cause:
In case of oil level is high.
ATF temperature is low when ATF quantity is checked.
In case of oil level is low.
ATF leaks is considered. Check the AT main unit and cooler circuit.
Page 4131 of 4264
DIAGNOSIS (JR405E) 7A2-139
No. Z11: Abnormal Oil Pressure
Description:
Oil pressure is low or high.
Possible Cause:
Basically, the same cause as "No. C1 - C8: Engine races up (slip) by shift up or shift down" is considered.
In case of oil pressure is low, faulty oil pump is considered.
No. Z12: Reverse Buzzer Does Not Ring
Description:
Reverse buzzer does not ring in R range.
Possible Cause:
Disordered select cable.
Disordered select lever.
Disordered inhibitor switch.