2004 ISUZU TF SERIES clutch

CONSTRUCTION AND FUNCTION 7A1-43
2nd Gear in D, 3, 2 Range
The driving force from the input shaft is transmitted to the rear sun gear and reverse & high clutch drum. As
in the case of the 1st gear, since the low clutch is engaged, the movement of the rear internal gear is
restricted. Since the 2-4 brake is engaged, the front sun gear is fixed. As a result, movement of the rear
internal gear is restricted, and the driving force transmitted to the rear sun gear rotates the rear planetary
carrier clockwise, and is decreased and output. The rotating speed of the rear planetary carrier is increased
as the rear internal gear rotates.
When decelerating, the engine brake is applied.

7A1-44 CONSTRUCTION AND FUNCTION
3rd Gear in D, 3 Range
The driving force from the input shaft is transmitted to the rear sun gear and reverse & high clutch drum. As
in the case of the 1st gear and 2nd gear, since the low clutch is engaged, the movement of the rear internal
gear is restricted. Since the high clutch is engaged, the driving force from the input shaft is directly
transmitted to the rear internal gear. As a result, the rpm of the rear sun gear and the rear internal gear
becomes the same as that of the input shaft so that the rear pinion gear rotates not independently but
together with the rear sun gear and rear internal gear.
When decelerating, the engine brake is applied.

CONSTRUCTION AND FUNCTION 7A1-45
4th Gear (O/D) in D Range
The driving force from the input shaft is transmitted to the rear sun gear and reverse & high clutch drum.
Since the 2-4 brake is engaged, the front sun gear is fixed. As a result, the front pinion gear rotates both
itself and together with other gears clockwise. This rotation increases the speed of rotation of the front
internal gear and is transmitted to the output shaft.

DIAGNOSIS (JR405E) 7A2-1
SECTION 7A2
DIAGNOSIS
TABLE OF CONTENTS
PAGE
BASIC TROUBLE SHOOTING..................................................................................................7A2-6
CHECK TRANS INDICATOR & SELF DIAGNOSIS..............................................................7A2-7
DIAGNOSIS WITH TECH 2........................................................................................................7A2-9
TECH 2 CONNECTION .................................................................................................. 7A2-9
TECH 2 OPERATING FLOW CHART (START UP)..............................................................7A2-10
TYPICAL SCAN DATA................................................................................................................7A2-13
MISCELLANEOUS TEST...........................................................................................................7A2-14
INTERMITTENT DIAGNOSIS....................................................................................................7A2-16
SNAPSHOT DISPLAY WITH TIS 2000....................................................................................7A2-17
SERVICE PROGRAMMING SYSTEM (SPS) ................................................................. 7A2-21
CIRCUIT DIAGRAM.....................................................................................................................7A2-24
PART LOCATION........................................................................................................................7A2-26
CONNECTOR LIST.....................................................................................................................7A2-31
DIAGNOSIS TROUBLE CODE TABLE...................................................................................7A2-33
FAIL-SAFE FUNCTION..............................................................................................................7A2-35
DTC P0722 (FLASH CODE 11) VEHICLE SPEED SENSOR NO SIGNAL......................7A2-36
DTC P0727 (FLASH CODE 13) ENGINE REVOLUTION SENSOR NO SIGNAL............7A2-38
DTC P0717 (FLASH CODE 14) TURBINE SPEED SENSOR NO SIGNAL......................7A2-40
DTC P0710 (FLASH CODE 15) ATF TEMPERATURE SENSOR FAILURE....................7A2-42
DTC P0560 (FLASH CODE 16) SYSTEM VOLTAGE FAILURE........................................7A2-43
DTC P0705 (FLASH CODE 17) INHIBITOR SWITCH FAILURE........................................7A2-44
DTC P1120 (FLASH CODE 22) THROTTLE SIGNAL FAILURE........................................7A2-46
DTC P1875 (FLASH CODE 25) GND RETURN CIRCUIT FAILURE.................................7A2-47
DTC P0753 (FLASH CODE 31) LOW & REVERSE BRAKE DUTY
SOLENOID FAILURE................................................................................................................7A2-48
DTC P0758 (FLASH CODE 32) 2-4 BRAKE DUTY SOLENOID FAILURE......................7A2-51
DTC P0763 (FLASH CODE 33) HIGH CLUTCH DUTY SOLENOID FAILURE................7A2-54
DTC P0768 (FLASH CODE 34) LOW CLUTCH DUTY SOLENOID FAILURE................7A2-57

7A2-2 DIAGNOSIS (JR405E)
PAGE
DTC P0748 (FLASH CODE 35) LINE PRESSURE SOLENOID FAILURE.......................7A2-60
DTC P1860 (FLASH CODE 36) LOCK-UP DUTY SOLENOID FAILURE.........................7A2-62
DTC P1853 (FLASH CODE 26) LOW & REVERSE BRAKE PRESSURE
SWITCH FAILURE......................................................................................................................7A2-64
DTC P1858 (FLASH CODE 27) 2-4 BRAKE PRESSURE SWITCH FAILURE................7A2-68
DTC P1863 (FLASH CODE 28) HIGH CLUTCH PRESSURE SWITCH FAILURE..........7A2-72
DTC P0731 (FLASH CODE 41) 1st GEAR RATIO ERROR................................................7A2-76
DTC P0732 (FLASH CODE 42) 2nd GEAR RATIO ERROR...............................................7A2-76
DTC P0733 (FLASH CODE 43) 3rd GEAR RATIO ERROR................................................7A2-76
DTC P0734 (FLASH CODE 44) 4th GEAR RATIO ERROR................................................7A2-76
DTC P1750 (FLASH CODE 51) LOW & REVERSE BRAKE FAIL-SAFE
VALVE FAILURE........................................................................................................................7A2-78
DTC P1755 (FLASH CODE 52) 2-4 BRAKE FAIL-SAFE VALVE FAILURE....................7A2-80
DTC P0602 Programming Error ................................................................................... 7A2-82
SYMPTOM DIAGNOSIS.............................................................................................................7A2-83
SYMPTOM DIAGNOSIS TABLE...............................................................................................7A2-84
No. A1: VEHICLE DOES NOT RUN IN D, 3, 2, L and RANGE..........................................7A2-93
No. A2: VEHICLE DOES NOT RUN IN R RANGE................................................................7A2-94
No. A3: VEHICLE DOES NOT RUN IN D, 3, 2 and RANGE...............................................7A2-95
No. B1: VEHICLE RUNS IN N RANGE...................................................................................7A2-96
No. B2: POOR ACCELERATION AT STARTING.................................................................7A2-97
No. B3: ENGINE RACE UP DURING STARTING (SLIP)....................................................7A2-100
No. B4: LARGE SHOCK WHEN SHIFT LEVER IS CHANGED TO N TO D
RANGE OR N TO R RANGE....................................................................................................7A2-103
No. B5: ENGINE STALLS WHEN SELECTING FROM N RANGE TO R, D, 3, 2
OR L RANGE...............................................................................................................................7A2-104
No. B6: ENGINE STARTER DOES NOT RUN IN P OR N RANGE...................................7A2-106
No. B7: ENGINE STARTER RUNS EXCEPT IN P OR N RANGE.....................................7A2-106
No. B8: EXTENDED TIME LAG WHEN SHIFT LEVER IS CHANGED TO N TO D........7A2-106
No. B9: EXTENDED TIME LAG WHEN SHIFT LEVER IS CHANGED TO N TO R........7A2-106
No. B10: BRAKE IS APPLIED IN R RANGE..........................................................................7A2-107
No. B11: INSUFFICIENT STARTING OR SHAKING IN D RANGE...................................7A2-107

7A2-6 DIAGNOSIS (JR405E)
BASIC TROUBLE SHOOTING

Transmission fluid pressure together with clutch and brake friction and other important transmission functions are
controlled by electrical signal from the Transmission Control Module (TCM).
Random diagnosis can produce inaccurate and misleading indications. It is important that diagnosing procedure be
carried out systematically.
Carefully follow the sequence outlined below to diagnose automatic transmission assembly.




Verify Customer Complain
Preliminary Check
(Visual Check/Test Drive)
Compare to Same Model
(If Available)
Check Service Bulletin
DTC Check
(Self-diagnosis/Tech 2)
Go to Symptom Diagnosis
Stall Test
Line Pressure Test
Transmission Overhaul
Repair & Verify Fix
Transmission Overhaul
Transmission Overhaul
Go to DTC Chart
Go to Intermittent Diagnosis NG
Follow the instructions
NG
No Instruction
NG
OK
NO DTC
Not Solved
OK
OK
Follow the Bulletin
(Once Clear Memory) Restored
Not Stored
Use Service Programming
System (SPS)
Not Solved

7A2-12 DIAGNOSIS (JR405E)
F0: Diagnostic Trouble Code
F0: Read DTC Infor As Stored By ECU
F1: Clear DTC Information
F1: Data Display
F2: Snapshot
F3: Miscellaneous Test
F0: Lamp
F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmission Check Light Test
F1: Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid
F4: Programming
F0: Program VIN
F1: Lock ECU

F0: Diagnostic Trouble Code
The purpose of the "Diagnostic Trouble Codes" mode is to
display stored trouble code in the TCM.
When "Clear DTC Information" is selected, a "Clear DTC
Information", warning screen appears. This screen informs you
that by cleaning DTC's "all stored DTC information in the TCM
will be erased".
After clearing codes, confirm system operation by test driving
the vehicle.

F1: Data Display
The purpose of the "Data Display" mode is to continuously
monitor data parameters.
The current actual values of all important sensors and signals
in the system are display through F1mode.
See the "Typical Scan Data" section.

F2: Snapshot
"Snapshot" allows you to focus on making the condition occur,
rather than trying to view all of the data in anticipation of the
fault. The snapshot will collect parameter information around a
trigger point that you select.

F3: Miscellaneous Test:
The purpose of "Miscellaneous Test" mode is to check for
correct operation of electronic system actuators.

F4: Programming (Factory Use Only):
The purpose of "Programming" is to program VIN in the ECM
and lock the programmed data.

7A2-14 DIAGNOSIS (JR405E)
MISCELLANEOUS TEST
The state of each circuit can be tested by using miscellaneous test menus. Especially when DTC cannot be
detected, a faulty circuit can be diagnosed by testing each circuit by means of these menus.
Even DTC has been detected, the circuit tests using these menus could help discriminate between a mechanical
trouble and an electrical trouble.

Connect Tech 2 and select "Powertrain", "JR 405E" & "Miscellaneous Test".
F0: Lamps
The circuit is normal if the warning light in the meter panel comes on and goes out in accordance with Tech 2
instruction.

Lamps

F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Tempeature Lamp Test
F3: Transmission Check Light Test


F0: Power Lamp Test


Power Lamp Test

Power Lamp Off



 Press "Active" key.
Then, "POWER DRIVE" indicator lamp is turned on in the meter panel.
 Press "Inactive" key.
Then, "POWER DRIVE" indicator lamp is turned off in the
meter panel.
 Press "Quit" Key to cancel the test.
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmisstion Check Light Test
Test procedure is same as "F0: Power Lamp Test".
The circuit is normal if the warning light in the meter panel
comes on and goes out in accordance with Tech 2 instruction.

F1: Solenoids
The circuit is normal if clicking sound is generated in accordance with Tech 2 instruction.

Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid