PARKING, LICENSE PLATE AND TAIL LAMPS
LT-143
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2004 November 2004 FX35/FX45
6. CHECK GROUND
1. Turn ignition switch OFF.
2. Check continuity between front side maker lamp harness con-
nector and ground.
3. Check continuity between clearance lamp harness connector
and ground.
4. Check continuity between license plate lamp harness connector
and ground.
5. Check continuity between rear combination lamp harness con-
nector and ground.
OK or NG
OK >> Check bulb.
NG >> Repair harness or connector.
Terminals
Continuity Front side marker lamp
Ground Connector Terminal (Wire color)
RH E22
2 (B) Yes
LH E42
PKIA5244E
Te r m i n a l s
Continuity Clearance lamp
Ground Connector Terminal (Wire color)
RH E23
3 (B) Yes
LH E43
SKIA5881E
Terminals
Continuity License plate lamp
Ground Connector Terminal (Wire color)
RH D111
2 (B) Yes
LH D110
PKIA5246E
Te r m i n a l s
Continuity Rear combination lamp (Side marker)
Ground Connector Terminal (Wire color)
RH B219
2 (B) Yes
LH B57
PKIA5247E
SERVICE DATA AND SPECIFICATIONS (SDS)
SC-39
C
D
E
F
G
H
I
J
L
MA
B
SC
Revision: 2004 November 2004 FX35/FX45
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
BatteryAKS0079N
StarterAKS0079O
AlternatorAKS0079P
Type80D23L
Capacity V - AH 12 - 52
Cold cranking current (For reference value)
A582
Applied model VK45DE VQ35DE (2WD) VQ35DE (AWD)
Ty p eM2T85075 S114 - 880 S114 - 881
MITSUBISHI
makeHITACHI make
Reduction gear type
System voltage V 12
No-loadTerminal voltage V 11
Current A Less than 145 Less than 90
Revolution rpm More than 3,300 More than 2,880
Minimum diameter of commutator mm (in) 31.4 (1.236) 28.0 (1.102)
Minimum length of brush mm (in) 11.0 (0.433) 10.5 (0.413)
Brush spring tension N (kg, lb)26.7 - 36.1
(2.72 - 3.68,
6.80 - 8.12)16.2 (1.65, 3.6)
Clearance between bearing metal and armature shaft mm (in) Less than 0.2 (0.008)
Clearance between pinion front edge and pinion stopper mm (in)0.5 - 2.0
(0.020 - 0.079)0.3 - 2.5 (0.012 - 0.098)
Applied model VK45DE VQ35DE
Ty p eLR1110 - 716 A3TG0191
HITACHI make MITSUBISHI make
Nominal rating V - A 12 - 110
Ground polarityNegative
Minimum revolution under no-load (When 13.5V is applied)
rpmLess than 1,100 Less than 1,000
Hot output current (When 13.5V is applied) A/
rpmMore than 70/1,800
More than 91/2,500
More than 110/5,000More than 37/1,300
More than 92/2,500
More than 103/5,000
Regulated output voltage V 14.1 - 14.7
Minimum length of brush mm (in) More than 6.00 (0.236) More than 5.00 (0.197)
Brush spring pressure N (g, oz)1.00 - 3.43
(102 - 350, 3.60 - 12.34)4.9 - 6.1
(499 - 622, 17.62 - 21.94)
Slip ring minimum outer diameter mm (in) More than 26.0 (1.024) More than 22.1 (0.870)
Rotor (Field coil) resistance Ω2.31 1.7 - 2.1
